Instructions / Assembly

ManualsBrandsBasement Watchdog ManualsPlumbing ProductDual-Float Switch with Controller

Dual Float Switch

The dual float switch contains two large

floating rings enclosed within a protective

cage. Water will lift the bottom float by a

1⁄4⬙, which will activate the pump. If for any

reason the lower float does not activate the

pump, the water will rise and activate the

second switch. As the pump evacuates the

water from the pit, the floats will drop. The

pump will run for an additional 10 seconds to

extend the cycle after the float returns to its

original position.

Note: When mounting the float switch, position

the bottom of the cage at the height you want

the pump to activate.

Installing the Dual Float Switch

The Basement Watchdog dual float switch is

easy to install by using the enclosed metal hose clamp.

1. Hold the float switch to the discharge pipe so the cage is below the

bracket.

2. Secure the float to the pipe with the enclosed hose clamp, but do not

completely tighten the clamp at this time.

3. Position the float switch to a level where the bottom of the float cage is

no lower than 3⬙ above the bottom of the pump and no higher than 1⬙

below the top of the pit. To avoid debris pouring into the float, it should

be positioned on the side of the discharge pipe opposite the drain tile.

Note: It is important to mount the float below the drain tile that empties

into the pit. Mounting it above the drain tile would allow water to fill the

drain tile before the pump is activated to pump out the water.

4. Once the float switch is in the desired position, tighten the clamp.

• ALWAYS disconnect the pump and dual float controller from the power source

before servicing or making adjustments.

• NEVER handle the controller, float switch, pump or motor with wet hands or when

standing on a wet or damp surface while the pump or controller is plugged into

the power source.

• MAKE SURE THERE IS A PROPERLY GROUNDED RECEPTACLE AVAILABLE. This

controller is wired with a 3-prong grounded plug. To reduce the risk of electric

shock, be certain that it is only connected to a properly grounded, 3-prong

receptacle. If you have a 2- prong receptacle, have a licensed electrician replace it

with a 3-prong receptacle according to local codes and ordinances.

• NEVER bypass grounding wires or remove the ground prong from the controller.

• DO NOT use an extension cord. The electrical outlet should be within the length

of the pump’s power cord, and at least 4 feet above the floor level to minimize

potential hazards from flood conditions.

• DO protect the electrical cord from sharp objects, hot surfaces, oil, and chemicals.

Avoid kinking the cord.

• MAKE SURE the supply circuit has a fuse or circuit breaker rated to handle the

power requirements noted on the nameplate of the pump.

• DO NOT expose the control unit to any type of moisture, water, rain or snow.

• DO NOT operate the pump or control unit if it has been damaged in any way.

• DO NOT use with pumps in pits handling raw sewage, salt water, or hazardous

liquids. This product is for use with ground water applications only.

• DO NOT use in continuous duty applications such as fountains or ponds.

• DO NOT disassemble the pump or control unit. When service is required, contact

Glentronics technical support at 800-991-0466, option 3. Return the product to

the manufacturer for any repairs at the following address:

Glentronics, Inc., 645 Heathrow Drive, Lincolnshire, IL 60069

• The control unit must receive 115V AC +/- 5% and 60 Hz from the AC outlet.

• The controller will not provide protection during a power outage. With the risk of

property damage from high water levels, the addition of a Basement Watchdog

battery backup sump pump system is highly recommended.

• After the initial installation, be sure to check the operation by filling the sump

with water and observing the pump operation through one full cycle.

 CAUTION

 WARNING

NOTICES

Risk of electric shock. To reduce this risk, observe

the following precautions.

To reduce the risk of hazards that can cause injury or

property damage, observe the following precautions.

Basement Watchdog

Dual Float Switch

& Controller

Instruction Manual

& Safety Warnings

Installation Instructions

Prior to Installation

1. Visually inspect the product. Products may be damaged during shipping. If the

product has been damaged, contact your place of purchase or Glentronics, Inc.

before installation.

2. Thoroughly read the instructions provided to learn specific details regarding

installation and use. This manual should be retained for future reference.

SAVE THESE INSTRUCTIONS. This manual contains

important SAFETY WARNINGS and OPERATING

INSTRUCTIONS for the Basement Watchdog Dual Float

Controller. You will need to refer to it before attempting

any installation or maintenance.

ALWAYS keep these instructions with the unit so that

they will be easily accessible. Failure to read and follow

these warnings and instructions could result in property

damage, serious injury, or death.

Summary of content (2 pages)

PAGE 1
Basement Watchdog Dual Float Switch & Controller Instruction Manual & Safety Warnings SAVE THESE INSTRUCTIONS. This manual contains important SAFETY WARNINGS and OPERATING INSTRUCTIONS for the Basement Watchdog Dual Float Controller. You will need to refer to it before attempting any installation or maintenance. ALWAYS keep these instructions with the unit so that they will be easily accessible.
PAGE 2
Dual Float Controller Model # BWC1 This control box is a piggyback switch that powers the Basement Watchdog Dual Float. The Dual Float Controller will activate the pump when either float is lifted, and then shuts off automatically 10 seconds after the float drops. Completing the Installation 1. After the initial installation, be sure to check the pump operation by filling the sump with water and observing the pump through one full cycle.