Bat-Caddy X3™ Electric Golf Caddy User Manual WARNING: PLEASE FOLLOW ALL ASSEMBLY INSTRUCTIONS AND READ AND UNDERSTAND THE OPERATING INSTRUCTIONS BEFORE YOU OPERATE THE CADDY.
TABLE OF CONTENTS Page 1. 2. 3. 4. 5. 6. 7. Packing List Parts Glossary Assembly Instructions Operating Instructions General Maintenance & Other Instructions Technical Specifications Frequently Asked Questions 1. Packing List 1 x Caddy Frame 2 x Rear Wheels 1 x Battery Pack (Battery, Bag, Leads) 1 x Charger 1 x Tool kit 2.
. Assembly Instructions 1. Unpack all items carefully and check inventory. 2. Place frame structure (one piece) on soft and clean ground to protect frame from being scratched. Erect Frame by unfolding and connecting the main frame tube together at the joint and locking the Y-shape lower support structure to the main frame with the frame lock mechanism. 3. Attach wheels to axles by pushing wheel locking button on the outside of the wheel and inserting the axle extension into the wheel.
. Place battery pack on battery tray and fasten Velcro strap around battery tightly. Insert battery plug into caddy outlet.
4. Operating Instructions 4.1. T-Handle Control Functions 4.1.1. Power Switch The ON/OFF button (see illustration) controls the caddy’s main power supply. Once you have connected the battery, make sure that the rheostat speed control is in OFF position. Now press the button for ca. 2 seconds in order to switch the caddy ON or OFF (similar to a mobile phone operation). Now the battery charge indicator LEDs will illuminate, and your caddy is ready for operation. 4.1.2.
4.1.4. Rheostat, Cruise Control and Brake/Stop Function : Easy scrolling action with the rheostat speed control knob on the handle lets you seamlessly choose your preferred speeds to suit your pace perfectly; To stop press the Cruise Control/Stop button. Once you are ready to go again press the button, and the cart will remember its last setting before you stopped, and travel at the same speed automatically. You can change the speed with the rheostat knob position. 4.2. Additional Functions 4.2.1.
3.2.4. Installation of Seat (Optional on some models) Attach and fasten holding bar to pre-drilled holes in frame using the locking pin. Some models have a preinstalled holding bar. Attach seat stand to seat bottom using the four small screws. Attention: Attach in such manner that the seat points parallel to the driving direction of the caddy with the opening to the outside, once you slide it into the holding bar. Slide seat stand into holding bar as shown.
5. Maintenance and Additional Instructions PLEASE OBEY THESE PRECAUTIONS FOR BATTERY USE & CHARGING a) Please do not charge the battery in a sealed container or in upside down position. It is recommended to charge the battery in a well ventilated area. b) Please do not charge the battery near a heater, or where heat accumulation may occur or in direct sunshine. c) In order to prolong the service life of the battery, please avoid complete discharge and charge the battery after every use.
irreversibly damaged f. Do not fully discharge the battery by “overplaying” it. It is recommended to recharge the battery after every 18 holes. 5.2. Test Caddy a. Testing Environment & Conditions First, make sure that you perform your first test of the caddy in a wide and safe area possibly on even surface, free of obstructions or valuables, such as people, parked automobiles, flowing traffic, furniture or water bodies (rivers, swimming pools etc.), steep hills, cliffs or similar hazards. b.
caddy often in bumpy terrain we recommend to add an additional bungee strap to the lower and/or upper bag support to give the golf bag additional hold and prevent it from shifting. Please avoid or minimize operation on hard and rough surfaces, such as cart paths, asphalt roads, gravel roads, roots etc., as this will cause unnecessary wear and tear on tires, wheels and other components. The caddy is best operated on soft and smooth surfaces such as fairways. 5.4.
you the charge level of the battery from green (fully charged) to red (discharged). Important: The electronics controller box contains no user serviceable parts. Therefore, it is sealed to reduce the risk of moisture entering and impacting the electronic system. Breaking this seal increases the risk of damaging the electronics and decreasing the reliability of your caddy. DO NOT attempt to open the controller case.
6.
Front Wheels Materials Colors Complimentary Accessories Airless, rubberized tread Frame: Aluminum Bag Support: ABS Painted: Silver Scorecard Holder Cup Holder Umbrella Holder Carrying Bag Rain Cover Sand Dispenser 1 Year on Parts & Labor (6 months on battery) Type: Cardboard Box, Styrofoam Cushioning Dimensions: 35 x 21 x 14” (92 x 55 x 34 cm) Gross Weight: 48 Lbs (22 kg) Additional Accessories Warranty Packaging Note: Bat-Caddy reserves the right to modify/
7. Frequently Asked Questions (FAQs) In order to provide our customers with the most accurate and in-depth information please read below some answers to the most frequently asked questions about electric golf caddies in general and the Bat-Caddy X3 in particular.
BAT-CADDY QUESTIONS Should I charge the battery once I receive the unit? Bat-Caddy: Our 12V sealed lead acid batteries come more or less fully charged, but we recommend charging them for a full 12 hours before the first usage. The charger should either have a blinking green light or a red light while it's charging and turn into a steady green light when the battery is charged. Batteries develop their full potential after a few charging cycles.
