Operation Manual

40
GB
Original Instructions
used for a preliminary assessment of exposure. The declared vibration
emission level represents the main applications of the tool. However
if the tool is used for different applications, with different accessories
or poorly maintained, the vibration emission may differ. This may
significantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into
account the times when the tool is switched off or when it is running but
not actually doing the job. This may significantly reduce the exposure
level over the total working period. Identify additional safety measures to
protect the operator from the effects of vibration such as: maintain the
tool and the accessories, keep the hands warm, organization of work
patterns.
OPERATION
Before use
• Remove any packing material and loose parts from unit.
• Check the accessories before use. It should be fit with the machine
and your purpose.
• If the machine is new, the battery must first be charged.
ATTENTION! After long time storage, the battery capacity
will be reduce.
A new battery or one which has not been used for an extended
period achieves full performance only after charging and
discharging cycles. A substantial drop in operating period per
charge indicates that the battery is worn out and must be
replaced.
WARNING!
• Do not allow familiarity with tools to make you careless.
Remember that a careless fraction of a second is enough to
cause serve injury.
• Before attempting to use this cordless drill, become familiar
with all of its operating features and safety requirements.
• To reduce the risk of serious personal injury, turn tool off and
disconnect battery pack before making any adjustments or
removing/installing attachments or accessories.
CHARGING PROCEDURE
• Connect the plug cable to the charger, and then plug into an
appropriate outlet before inserting battery pack. After approx 5 sec,
all three charging lights will be on for two seconds and then off,
indicating power is available at the charger.
(fig. A)
• Insert the battery pack into the charger, making sure the pack is
fully seated in the charger. The charging process has now begun.
(fig. B) During the charging process, the charging lights will
indicate the charging status as below:
- Less than 30% charged, all three charging lights will blink in
sequence.
- Less than 60% charged, one light will stay on, while the other two
lights will blink in sequence.
- Over 60% charged, two lights will stay on, while the remaining
light will blink continuously.
- Fully charged, all three lights will remain on continuously.
• As a guide, the charging process will be last approximate 30 min for
a 2 Ah Battery Pack and approx 60 min for a 4Ah battery pack, and
will be displayed by permanent lighting of all three charging lights.
CHARGER DIAGNOSTICS
The charger is designed to detect certain problems that can arise with
battery packs.
• When the charger detects a battery pack that is overheated, all
three charging light will blink at the same time. Please remove the
battery and allow it to cool down for 15 – 30 minutes and re-insert.
• When the charger detects malfunction in the battery or the charger,
two charging lights will blink at the same time. Please remove the
battery and allow to cool down for 15 – 30 minutes. Then re-insert
the battery pack into the charger, if two charging lights still flashes,
the battery or charger may require service.
NOTE: Charging times maybe longer depending on the surrounding
temperature and battery conditions.
Fitting and removing the battery pack to the drill
• To install the battery pack to the tool, align the raised portion of the
battery pack with the grooves on the bottom of the drill, and slide it
firmly into the handle until you hear the lock snap into place.
(fig. C)
• To remove the battery pack from the tool, press the battery pack
release button and slide the battery pack completely out of tool
handle.
Battery charging
CAUTION!
• Before attempting to charge the battery, check the charger
and the battery to ensure the charging equipment matches
the battery supplied. The components are all labeled with
component numbers.
• The rechargeable battery is not fully charged on leaving the
factory. Charge the rechargeable battery before first use.
• Recharge discharged batteries as soon as possible after use or
battery life may be greatly diminished. For longest battery life,
do not discharge batteries fully.
WARNING: Never use a damaged battery pack.
WARNING: Always disconnect the charger from the power
source when it is not in use.
WARNING: The charger supplied is matched to the Li-ion
battery installed in the machine. Do not use another charger.
Touch_MA_multi_1404-30.indd 40 01-05-14 15:33