SDS

MATERIAL SAFETY DATA SHEET
FOR COATINGS, RESINS, AND RELATED MATERIALS
Prepared by: Compliance Dept.
SECTION I - PRODUCT IDENTIFICATION
MANUFACTURER: Munro Products
DISTRIBUTOR: 9150 Clarence Center Road
Clarence Center, NY 14032
INFORMATION: 716/741-9450
EMERGENCY: CHEMTREC
®
1-800-424-9300
PRODUCT NAME:
SLIP GUARD ADDITIVE
TRADE NAME: BathWorks Fine Grit
CODE: Slip Guard Additive
SECTION II - HAZARDOUS INGREDIENTS
COMMON NAME CHEMICAL NAME
POLYPROPYLENE PIGMENT 1-PROPENE HOMOPOLYMER POLYOLEFINS CAS #9003-07-0
HMIS+
RATING
Polypropylene Texturing Pigment Health hazard: 0 Minimal
and Flattening Agents Flammability hazard: 1 Slight
Reactivity hazard: 0 Minimal
APPEARANCE AND ODOR: White particulate; odorless
Hazar
dous Ingr
edients
Recommended Atmospher
e Levels**
latot m/gm01 enelyorpyloP
5mg/m respirable
Our supplier interprets the U.S. Occupational Safety and Health Act and Regulations, including the
Hazard Communication Standard 29 CFR 1910.1200 dated November 25, 1983, this product should
NOT be considered a health hazard material.
**Air level recommended by our supplier.
SECTION III - PHYSICAL DATA
BOILING POINT: NA VAPOR PRESSURE @ 20 degree C: NA
VAPOR DENSITY: Negligible at 20 degree C % VOLATILE (vol.): N / A
FREEZING POINT: NA SOLUBILITY IN WATER: Negligible
SPECIFIC GRAVITY: 0.9 pH: NA
EVAPORATION: NA
SECTION IV - FIRE AND EXPLOSION HAZARD DATA
CAUTION! MAY FORM FLAMMABLE DUST-AIR MIXTURES.
FLASH POINT: 276 degree C (530 degree F) COC, ASTM D57-92
AUTOIGNITION TEMPERATURE : Not determined
EXTINGUISHING MEDIA: Water spray, dry chemical, foam, carbon dioxide or halon.
SPECIAL FIRE-FIGHTING PROCEDURES: None
UNUSUAL FIRE & EXPLOSION HAZARDS: May form flammable dust-air mixtures.
STABILITY CONSIDERATIONS: Stable
INCOMPATIBILITY WITH: Avoid contact with hot or concentrated nitric and perchloric acids, fuming
sulfuric acid or 98% sulfuric acid at 60 degrees C (140 degree F) or above.
HAZARDOUS DECOMPOSITION PRODUCTS: None
HAZARDOUS PRODUCTS OF COMBUSTION: Combustion products depend on temperature, other
materials present and air supply. They can be carbon monoxide, carbon dioxide, acrolein, formaldehyde,
other aldehydes, ketones, fatty acids, methane, ethane and unsaturated hydrocarbons. Carbon
monoxide is the most prominent.
HAZARDOUS POLYMERIZATION: Will not occur.
SECTION V - HEALTH HAZARD DATA
SIGNS AND SYMPTOMS OF OVEREXPOSURE IN THE WORKPLACE: None known
EMERGENCY AND FIRST AID PROCEDURES: Not applicable.
MEDICAL CONDITIONS GENERALLY RECOGNIZED AS BEING AGGRAVATED BY EXPOSURE: Not
Known
PRIMARY ROUTE OF ENTRY: Inhalation
Not evaluated for carcinogenicity by IARC (International Agency for Research on Cancer), NTP (National
Toxicology Program) or the OSHA (Occupational Safety & Health Administration). There is no evidence
of carcinogenicity in any animal species.
REPORTED HUMAN EFFECTS: None known
REPORTED ANIMAL EFFECTS: None known
DATE OF PREPARATION - 01-03-2009
NON WARRANTY
The information presented herein, while not guaranteed, is to the best of our knowledge true and
accurate. No warranty or guarantee expressed or implied is made regarding the performance of any
product, since the manner of use is beyond our control. No suggestion for product use, nor anything
contained herein, shall be construed as a recommendation for its use in infringement of any existing
patent, and Munro assumes no responsibility or liability for operations that do infringe any such patents.
TUB REFINISHING, INC. DBA MUNRO PRODUCTS
SPECIAL NOTATION:
Munro Products, BathWorks, TubWorks & Tub Refinishing, Inc. are not responsible for accidents related
to the application of the slip guard products on bathtubs, shower bases or other areas needing the slip
guard application. The customer should test, maintain and care for all slip guard areas through the life
time of the slip guard application. Special attention, caution and maintenance is recommended.
SECTION VI - SPECIAL PRECAUTIONS AND ADDITIONAL COMMENTS