SDS

Product ingredients appear on the following carcinogenic listings: (X) IARC (X) NTP ( ) OSHA
()None of the above.
PRIMARY ROUTE(S) OF ENTRY (X) SKIN (X) BREATHING (X) SWALLOWING
FIRST AID
IN CASE OF SKIN CONTACT – Wash area thoroughly with soap and water. Remove soiled clothing. Get
medical assistance if irritation persists. Wash clothing before reuse.
IN CASE OF EYE CONTACT – Flush with large amounts of water for at least 15 minutes. Get medical
assistance.
IF SWALLOWED – GET MEDICAL ATTENTION IMMEDIATELY. DO NOT induce vomiting. Aspiration of
material into lungs can cause chemical pneumonitis which may be fatal.
IF INHALED – If you experience difficulty in breathing, leave the area to obtain fresh air. If continued
difficulty is experienced, summon medical assistance immediately. If breathing ceases, restore using
approved CPR techniques and summon medical help immediately.
SECTION VI - REACTIVITY DATA
HAZARDOUS POLYMERIZATION STABILITY - Stable
– Will NOT occur
CONDITIONS TO AVOID AND INCOMPATIBILITIES
– Avoid heat, sparks and flame.
– Can react vigorously, even violently, with oxidizing materials.
– Additional incompatible Materials:
– Acids, oxidizing materials, alkalis, nitrates, strong alkalis, hydrazine, calcium hypochlorite, performic
acid and bromine pentafluoride.
HAZARDOUS DECOMPOSITION PRODUCTS (Including Thermal Decomposition)
– Carbon dioxide, carbon monoxide, oxides of nitrogen and various hydrocarbons.
SECTION VII - SPILL OR LEAK PROCEDURES
SMALL SPILL – Absorb liquid on inert material such as paper, vermiculite, floor absorbent, and transfer
to hood.
LARGE SPILL – Eliminate all ignition sources (flares, flames, including pilot lights, electrical sparks).
Persons not wearing protective equipment should be excluded from area of spill until cleanup has been
completed. Stop spill at source, contain area of spill to prevent spreading, pump liquid to salvage tank.
Remaining liquid may be absorbed with inert material such as sand, clay, earth, or floor absorbent, and
shoveled into containers with non-sparking tools. Prevent run-off to sewers, streams, or other bodies of
water. If run-off occurs, notify the proper authorities as required that a spill has occurred.
WASTE DISPOSAL METHOD – Dispose of contaminated absorbent, container, and unused contents in
accordance with local, state, and federal regulations. Do not incinerate closed containers.
SECTION VIII - PROTECTIVE EQUIPMENT
VENTILATION/RESPIRATORY PROTECTION – Use only with adequate ventilation. Maintain continuous
flow of fresh air. Do not breathe vapors, spray mists, or sanding dusts. Wear appropriate properly fitted
respirator (NIOSH?MSHA approved) during and after application unless air monitoring demonstrates
vapor and particulate levels are below applicable limits. Follow respirator manufacturer’s directions for
respirator use. Engineering or administrative controls should be implemented to reduce exposure.
Provide sufficient mechanical (general and/or local exhaust) ventilation to maintain exposure below
TLV(s).
PERSONAL PROTECTIVE EQUIPMENT – Do not get in eyes, on skin, or on clothing. Use solvent
resistant safety eyewear with splash guards. Solvent impermeable gloves, clothing, and boots should be
worn to prevent skin contact.
SECTION IX - SPECIAL PRECAUTIONS AND ADDITIONAL COMMENTS
Keep container tight and upright to prevent leakage. Keep container closed when not in use. Do not store
above 49 C/120 F. Do not transfer contents to bottles or other unlabeled containers. Containers of this
material may be hazardous when emptied because they retain product residues (vapor, liquid, and/or
solid). When empty, may
contain explosive vapors. Do not cut, puncture or weld on or near this container.
All hazard precautions given in this data sheet must be observed for empty containers.
IMPORTANT! – This product may be blended with other products prior to use. Read all warnings and
precautions on the MSDSs and labels of all products being blended as the combination may contain the
hazards of each component.
NON-WARRANTY – Any recommendation of Munro contained herein covering use utilization, chemical
or physical properties and other qualities of the products sold is believed reliable; however, Munro makes
no warranty or representation with respect thereto. Use of application of any Munro products is at the
discretion of the Buyer without liability or obligation whatsoever of Munro.
FOR INDUSTRIAL USE ONLY – This product is for use by professional, trained personnel using proper
equipment, and is not intended for sale to, or use by the general public.
SECTION X - SHIPPING DATA
D.O.T. PROPER SHIPPING NAME: Paint I.M.O. SHIPPING NAME: Paint
D.O.T. LABEL(S) REQUIRED: Flammable Liquid I.M.O. CLASS NUMBER: 3
D.O.T. HAZARD CLASS: 3, Flammable Liquid I.M.O. UN NUMBER: UN 1263
D.O.T. UN/NA ID NUMBER: UN 1263 I.M.D.G. PAGE NUMBER: 3372
PACKING GROUP: III
F LINE - LEAD FREE 10-24-85 R. 02-26-86 R.08-19-88
R.08-24-92 R.05-12-93 R.12-09-94
THE INFORMATION CONTAINED HEREIN IS INFORMATION RECEIVED FROM OUR RAW MATERIAL
SUPPLIERS AND OTHER SOURCES AND IS BELIEVED TO BE RELIABLE. THIS DATA IS NOT TO BE
TAKEN AS A WARRANTY OR REPRESENTATION FOR WHICH MUNRO ASSUMES LEGAL
RESPONSIBILITY.
TUB REFINISHING, INC. DBA MUNRO PRODUCTS