Safety Data Sheet 1. Identification BATHWORKS® DIY Refinishing Kit – Part B Base Hardener Munro Products (716) 741-9450 9150 Clarence Center Road Clarence Center, NY 14032 www.bath-works.net 1.1 Product Name 1.2 Distributor 1.3 Emergency Information 2.1. CHEMTREC® Poison Control Center (800) 424-9300 (800) 854-6813 2. Hazard Identification Classification of the substance or mixture Flam. Liq. 3; H226 Flammable liquid and vapor. Skin Sens. 1; H317 May cause an allergic skin reaction. Resp. Sens.
P403+233 Store in a well ventilated place. Keep container tightly closed. 2.3 HMIS Rating Health: 3 Flammability: 3 Reactivity: 0 3. Ingredient Composition This product contains the following substances that present a hazard within the meaning of the relevant State and Federal Hazardous Substances regulations.
5.1. Extinguishing media 5.2. Special hazards arising from the substance or mixture 5.3. Advice for firefighters 5.4. ERG Number 5. Firefighting CAUTION: This product has a very low flashpoint. Use of water spray when fighting fire may be inefficient. CAUTION: For mixtures containing alcohol or polar solvent, alcohol-resistant foam may be more effective. SMALL FIRES: Use dry chemical, CO2, water spray or regular foam. LARGE FIRES: Use water spray, fog, or regular foam. Do not use straight streams.
0000123-86-4 BUTYL ACETATE OSHA ACGIH NIOSH Supplier OHSA, CAN Mexico 0000822-06-0 Hexamethylene diisocyanate Brazil OSHA ACGIH NIOSH Supplier OHSA, CAN 0028182-81-2 Hexamethylene diisocyanate homopolymer 0064742-95-6 Petroleum naphtha Mexico Brazil OSHA ACGIH NIOSH Supplier OHSA, CAN Mexico Brazil OSHA ACGIH NIOSH Supplier OHSA, CAN Mexico Brazil 150 ppm TWA; 710 mg/m3 TWA 200 ppm STEL; 950 mg/m3 STEL 150 ppm TWA 200 ppm STEL 150 ppm TWA; 710 mg/m3 TWA 200 ppm STEL; 950 mg/m3 STEL 1700 ppm ID
0064742-95-6 Petroleum naphtha NIOSH Ingredient BUTYL ACETATE Source OSHA NTP IARC No Established Limit Carcinogen Data CAS No. 0000123-86-4 0000822-06-0 0028182-81-2 0064742-95-6 Hexamethylene diisocyanate OSHA NTP IARC Hexamethylene diisocyanate homopolymer OSHA NTP IARC Petroleum naphtha OSHA NTP IARC 8.2.
soiled clothing and wash clothing thoroughly before reuse. Shower after work using plenty of soap and water. Appearance 9.
harmful or fatal. Ingredient Hexamethylene diisocyanate homopolymer - (28182-81-2) BUTYL ACETATE - (123-86-4) Petroleum naphtha - (64742-95-6) Hexamethylene diisocyanate (822-06-0) Oral LD50, mg/kg 5,000.00, Rat - Category: 5 10,700.00, Rat - Category: NA 6,800.00, Rat -Category: NA No data available Skin LD50, mg/kg No data available 17,600.00, Rabbit - Category: NA 3,400.
13.1 Waste treatment methods Do not allow spills to enter drains or watercourses. Dispose of in accordance with local, state and federal regulations. (Also reference RCRA information in Section 15 if listed). 14. Transportation Information 14.1 UN number 14.2 UN proper shipping name 14.3 Transport hazard class(es) Proper Shipping Name UN Number Hazard Class Packaging Group UN 1263 PAINT DOT (Domestic Surface Transportation) PAINT UN 1263 3 III CERCLA/DOT RQ: 5359 gal. / 50000 lbs. 14.
Proposition 65 - Female Repro Toxins (>0%): Proposition 65 - Male Repro Toxins (>0%): (No Product Ingredients Listed) Proposition 65 - Developmental Toxins (>0%): (No Product Ingredients Listed) SDS Revision Date: (No Product Ingredients Listed) 16. Other Information 3/11/2014 The information and recommendations contained herein are based upon data believed to be correct. However, no guarantee or warranty of any kind, expressed or implied, is made with respect to the information contained herein.
Safety Data Sheet 1. Identification BATHWORKS® DIY White High Speed Filler BATHWORKS® Chip Filler Munro Products (716) 741-9450 9150 Clarence Center Road Clarence Center, NY 14032 www.bath-works.net 1.1 Product Name 1.2 Distributor 1.3 Emergency Information CHEMTREC® Poison Control Center 2. 2.1 Classification of the substance or mixture: (800) 424-9300 (800) 854-6813 Hazard Identification Flammable Liquids 3 Skin Corrosion/Irritation 2 Eye Damage/Irritation 2B Acute Toxicity-Inhalation 4 2.
3. 3.1 Mixtures Chemical Identity Polyester Resin Unsaturated Polyester Resin Styrene Monomer Sodium Borosilicate Glass Magnesium Silicate Barium Sulfate Titanium Dioxide m-Tolyl Diethanolamine Methyl Alcohol Ingredient Composition CAS No. 28472-89-1 Proprietary 100-42-5 65997-17-3 14807-96-6 7727-43-7 13463-67-7 91-99-6 67-56-1 Concentration 20% 3% 10% 5% 40% 10% 10% 1% 1% 4. First Aid 4.
5.3 Flash Point: 5.4 Special protective actions for fire-fighters: violent rupture of the container. Combustion may produce carbon monoxide, carbon dioxide and irritating or toxic vapors and gases. 89° F (32 ° C). Wear self-contained breathing apparatus (SCBA) and full fire-fighting protective clothing. Thoroughly decontaminate all protective equipment after use. Evacuate all persons from the fire area to an explosion-protected location.
8. 8.1 Control parameters Component CAS No. Exposure Controls & Personal Protection EINECS Exposure Limits Source 100 ppm PEL OSHA Styrene 100-42-5 202-851-5 10% - 12% 20ppm TWA ACGIH 40 ppm STEL ACGIH 8.2 Appropriate engineering Local ventilation may be required during certain operations to maintain controls: concentrations below recommended exposure limits. Use explosion-proof ventilation equipment. 8.
9.16 Auto-ignition temperature: 9.17 Decomposition temperature: 9.18 Viscosity: 9.19 Volatile Organic Compounds: 10.1 Reactivity: 10.2 Chemical stability: 10.3 Possibility of hazardous reactions: 10.4 Conditions to avoid: N/A 10.5 Incompatible materials: 10.6 Hazardous decomposition products: 914° F (490° C) N/A N/A 12% by mass (186 g/liter) 10. Stability & Reactivity N/A Stable at normal temperatures and storage conditions.
assay. 11.4 Numerical measures of toxicity: Ingredient Name CAS No. m-Tolyldiethanolamine 91-99-6 % 0.5% - 1% Styrene 100-42-5 10% - 12% Test LD50 LD50 LD50 LD50 Result Route Species 0.8 – 3.1 g/kg 24 g/m3, 4 hrs. 5g/kg 5g/kg Oral Inhalation Oral Dermal Rat Rat Rat Rabbit 12. Ecological Information 12.1 Ecotoxicity: Chemical Name CAS No. % Test Concentration Result Species Styrene 100-42-5 10% - 12% LC50 23 mg/L 48 hrs.
CERCLA: SARA Title III: Section 311/312 - Hazard Communication Standard (HCS): SARA Title III: Section 313 Toxic Chemical List (TCL): TSCA Section 8(b) - Inventory Status: TSCA Section 12(b) - Export Notification: This material is classified as an IMMEDIATE HEALTH HAZARD, DELAYED HEALTH HAZARD, FLAMMABILITY HAZARD, and REACTIVITY HAZARD under the US Superfund Amendment and Reauthorization Act (Section 311/312).
Safety Data Sheet 1.1 Product Name 1.2 Distributor 1.3 Emergency Information 2.1 OSHA/HCS status 2.2 Classification of the substance or mixture 2.3 Signal Words 2.4 Pictograms 2.5 Hazard Statements 2.6 Precautionary Statements Prevention Response 1. Identification BATHWORKS® DIY Refinishing Kit - Part A Base Color Munro Products 9150 Clarence Center Road Clarence Center, NY 14032 (716) 741-9450 CHEMTREC® Poison Control Center (800) 424-9300 (800) 854-6813 www.bath-works.net 2.
Storage Disposal 2.7 Supplemental label elements 2.8 Hazards not otherwise classified 3.1 Substance/mixture immediately all contaminated clothing. Rinse skin with water or shower. IF ON SKIN: Wash with plenty of soap and water. Wash contaminated clothing before reuse. If skin irritation or rash occurs: Get medical attention. Store locked up. Store in a well-ventilated place. Keep cool. Dispose of contents and container in accordance with all local, regional, national and international regulations.
4.2 Most significant signs/symptoms Acute health effects Eye Contact No known significant effects or critical hazards. Skin Contact Harmful if inhaled. Inhalation Defatting to the skin. May cause skin dryness and irritation. May cause an allergic skin reaction. Ingestion No known significant effects or critical hazards. Overexposure signs/symptoms Eye Contact Skin Contact Inhalation Ingestion 4.3 Notes to Physician 4.4 Specific Treatments 4.5 Protection of first-aiders No specific data.
appropriate respirator when ventilation is inadequate. Put on appropriate personal protective equipment. For emergency responders If specialized clothing is required to deal with the spillage, take note of any information in Section 8 on suitable and unsuitable materials. See also the information in "For nonemergency personnel". Environmental precautions Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers.
area. Store i n original container protected from direct sunlight in a dry, cool and well-ventilated area, away from incompatible materials (see Section 10) and food and drink. Eliminate all ignition sources. Separate from oxidizing materials. Keep container tightly closed and sealed until ready for use. Containers that have been opened must be carefully resealed and kept upright to prevent leakage. Do not store in unlabeled containers. Use appropriate containment to avoid environmental contamination. 8.
8.4 Environmental exposure controls 8.5 Hygiene measures 8.6 Eye/face protection 8.7 Hand protection 8.8 Body protection 8.9 Other skin protection 8.10 Respiratory protection controls also need to keep gas, vapor or dust concentrations below any lower explosive limits. Use explosion-proof ventilation equipment. Emissions from ventilation or work process equipment should be checked to ensure they comply with the requirements of environmental protection legislation.
Evaporation rate Not available. Vapor pressure Not available. Vapor density Not available. Relative density 1.48 Density (lbs / gal) 12.35 Solubility Insoluble in the following materials cold water. Partition coefficient: n- octanol/water Not available. Viscosity Kinematic (40°C (104°F)) >0.21 cm2/s (>21 cSt) Volatility 36% (v/v), 19.865% (w/w) % Solid. (w/w) 80.135 10.1 Reactivity 10.2 Chemical stability 10.3 Possibility of hazardous reactions 10.4 Conditions to avoid 10.
11.5 Carcinogenicity There are no data available on the mixture itself. Product/ingredient name OSHA IARC NTP titanium dioxide 2B crystalline silica, respirable powder (>10 microns) 1 Known to be a human carcinogen. Carcinogen Classification code: IARC: 1, 2A, 2B, 3, 4 NTP: Known to be a human carcinogen; Reasonably anticipated to be a human carcinogen OSHA: + Not listed/not regulated: 11.6 Reproductive toxicity There are no data available on the mixture itself. 11.
Exposure to component solvent vapor concentrations in excess of the stated occupational exposure limit may result in adverse health effects such as mucous membrane and respiratory system irritation and adverse effects on the kidneys, liver and central nervous system. Symptoms and signs include headache, dizziness, fatigue, muscular weakness, drowsiness and, in extreme cases, loss of consciousness. Solvents may cause some of the above effects by absorption through the skin.
12.3 Bioaccumulative potential Product/ingredient LogPow name heptan-2-one 12.4 Mobility in soil 1.98 BCF Potential - low Soil/water partition coefficient (KOC) Not available. 13. Disposal Information The generation of waste should be avoided or minimized wherever possible. Disposal of this product, solutions and any by-products should at all times comply with the requirements of environmental protection and waste disposal legislation and any regional local authority requirements.
15.2 SARA 302/304 SARA 304 RQ Not applicable. Composition/information on ingredients No products were found. 15.3 SARA 311/312 Classification FLAMMABLE LIQUIDS: Category 3 ACUTE TOXICITY (inhalation): Category 4 SKIN SENSITIZATION: Category 1 CARCINOGENICITY: Category 1A HNOC: Defatting irritant 15.4 Composition/information on ingredients Ingredient Percent titanium dioxide ≥20 - ≤50 heptan-2-one ≥10 - <20 crystalline silica, respirable powder (>10 microns) maleic anhydride ≤1.0 <0.
The information and recommendations contained herein are based upon data believed to be correct. However, no guarantee or warranty of any kind, expressed or implied, is made with respect to the information contained herein. We accept no responsibility and disclaim all liability for any harmful effects which may be caused by exposure to our products. Customers/users of this product must comply with all applicable health and safety laws, regulations, and orders. Tub Refinishing Inc.