Instruction for Use

EN
9
OPTIONS AND SETTINGS
TABLET (All-in-one)
This setting allows you to optimise the performance of the cycle
according to the type of detergent used. Enable it if you use combined
detergents in tablet form (rinse aid, salt and detergent in 1 dose).
To set the Tablet, enter in the setting
menu by pressing „OK” button and
navigate with „< , >” until „TABLET”
is shown, then press „OK” button.
START DELAY
The start of the cycle may be delayed for a selected period of time.
To set a delay, enter in the setting menu by pressing „OK” button and na-
vigate with „< , >” until „START DELAY” is shown, then press „OK” button.
With each press of the button “>” or “<“, the delay start increases by:
• every 0:30 if selection below 4 hours,
• every 1:00 if selection is below 12 hours,
• every 2 hours if selection is above 12 hours.
To remove the delay, press „<” or „>”
button until „OFF” is displayed.
Default value is OFF.
If delay is selected, the is lit
Once „OK” button is pressed the
delay is conrmed and the machine
comes back to the cycle selection
screen with delay value visible.
Press „START” and close the door within 4 sec. to start the delay
MULTIZONE
If there are not many dishes to be washed it can be loaded in one rack
only. Using this option you can select which rack you want to wash.
To set the Multizone, enter in the setting menu by pressing „OK”
button and navigate with „< , >” until „MULTIZONE” is shown, then
press „OK” button.
By default the MULTIZONE is not
active and all racks icons are lit.
The multizone icon becomes lit.
The multizone icon becomes lit.
The multizone icon becomes lit.
POWER CLEAN
Thanks to additional water jets this option provides a more intensive
and powerful wash in the specic area of lower rack.
Default value is OFF.
To set the Power Clean, enter in
the setting menu by pressing „OK
button and navigate with „< , >”
until „POWER CLEAN” is shown,
then press „OK” button.
TURBO
This option can be used to reduce the duration of the main cycles
while maintaining washing and drying performance levels.
To set the Turbo, enter in the setting
menu by pressing „OK” button and
navigate with „< , >” until „TURBO” is
shown, then press „OK” button.
With each press of the button „>”
or „<“ option will be ON or OFF.
Conrm by pressing „OK” button.
FLOOR LIGHT
A LED light projected on the oor indicates that the dishwasher is
working. The light stays on during the cycle and switches o at the
end of the cycle.
This feature is active by default, but it is possible to deactivate it in the
“SETTINGS MENU”.
TUB LIGHT
When the feature is active the LEDs in the tub are automatically swit-
ched on/o as soon as the user open/close the door respectively.
If the door remains opened for more than 10 min, the LEDs in the
tub switch o (to turn them on again, the door has to be closed and
opened again).This feature is active by default, but it is possible to
deactivate it in the “SETTINGS MENU”.
TABLET OFF
TABLET ON
TABLET ON
START DELAY OFF
<STARTS IN h> OFF
<STARTS IN h> 4:00
<STARTS IN h> 4:00
MULTIZONE OK
<CUTLERY ONLY>
<ALL RACKS> <>
<LOW ONLY> <>
<CUTLERY ONLY> <>
<HIGH ONLY> <>
POWER CLEAN OFF
POWER CLEAN ON
POWER CLEAN ON
TURBO OFF
TURBO ON
TURBO ON
With each cycle additional options can be used. A full list of available options working with specic cycles can be found in the Cycle Table on
the previous page. All active options are shown on the display.
To set an option press „OK” button. SET OPTIONS message is shown for a few seconds. Then use „<” or „>” button to navigate through the
option list. Press „OK” to select the option, in the setting menu the LED above „OK” button is lit.
If the option is not available, it will be still visible in its position but with „ ”