Quick Start Guide

ManualsBrandsBauknecht ManualsDishwasherGMX 61102

GBD NLF

Before using the dishwasher, you are advised to read the user instructions!

On/Off button

Press the button to switch on the

dishwasher. The indicator light for the last

programme to be selected lights up; at the

end of the cycle the dishwasher emits a

brief audible signal.

Programme selection button

Press this button to select the desired

programme.

The indicator light of the selected

programme illuminates.

Indicator lights

Add regeneration salt

Only add regeneration salt immediately

before starting a wash programme.

Add rinse aid

Options

Half load

selector button

Press this button to select the half load

option; the corresponding indicator light

will illuminate. Press the button again to

the deselect the option; the corresponding

indicator light will go out.

The half load function is suitable for

smaller wash loads. The dishes should be

distributed over both racks.

Antibacterial rinse

(Sani Rinse option)

This function adds an antibacterial rinse at

the end of the wash cycle, guaranteeing a

further reduction of bacteria. The indicator

light illuminates when the function is

activated.

If the temperature is not maintained at a

constant level during the antibacterial rinse

programme (e.g. if the door is opened or

there is a power cut), the programme

indicator lights will flash to signal that the

sanitizing effect of the antibacterial rinse is

not guaranteed.

“Delayed start” button

The wash cycle can be programmed to

start after 1-12 hours. The delayed start

can be programmed either before or after

selecting the desired wash programme.

When the door is closed, a pre-wash cycle

is run, after which the delayed start

countdown begins.

Quick Wash

This option, when selected together with

any wash programme (except pre-rinse )

SHORTENS THE DURATION of the

selected wash cycle from a minimum of

10% to a maximum of 55%, depending on

the programme selected.

This function is activated by pressing the

QUICK WASH button after having

selected the desired programme.

Tablets selector

This setting allows you to optimize the

wash cycle in accordance with the type of

detergent used. If you use combined

detergents that combine detergent, rinse

aid and/or salt in 1 tablet

Press the «Antibacterial rinse» + «Quick

Wash» buttons simultaneously (the

«Tablet» indicator light will illuminate). If

you are using a powder or liquid

detergent, the «Tablet» indicator on the

control panel must be off.

QUICK REFERENCE GUIDE

Summary of content (8 pages)

PAGE 1
GB QUICK REFERENCE GUIDE Before using the dishwasher, you are advised to read the user instructions! If the temperature is not maintained at a constant level during the antibacterial rinse programme (e.g. if the door is opened or there is a power cut), the programme indicator lights will flash to signal that the sanitizing effect of the antibacterial rinse is not guaranteed. On/Off button Press the button to switch on the dishwasher.
PAGE 2
GB Fault indicators Indicator lights Off Blinking On The water stop device has been activated Switch off the appliance and contact After-Sales Service. The dishwasher has filled with too much water Reset and start the programme again from the beginning. If the problem persists, contact After-Sales Service. Water heating system Reset and start the programme again from the beginning. If the problem persists, contact After-Sales Service.
PAGE 3
GB Detergent 2) Programme Table Loading tips A B Litres kWh Minutes Pre-wash cold Dishes to be washed later. _ _ 3,5 0,02 15 Delicate 45°C Lightly soiled items, with no dried-on food. X _ 9,5 1,10 65 Rapid 38°C Light soiling, for example glasses and cups. X _ 11 0,85 45 Eco 1) 50°C Normally soiled items. X _ 10 1,03 165 Eco fast 60°C Normally soiled items, without final drying. X _ 12,5 1,25 70 Auto 60-70°C Normally or heavily soiled dishes.
PAGE 4
GB HOW TO USE THE APPLIANCE Further indications are given in the individual chapters and in the user instructions. Open the door Press the On/Off button. C Large compartment A A B How to fill the detergent dispenser Small compartment B indicator C. Check the rinse aid level Mechanical Electrical indicator light on control panel (if present). Check the salt level Load the racks D On models with water softener system only. Mechanical indicator D.
PAGE 5
GB LOADING THE DISHWASHER RACKS Upper rack: Cup support rack (A): Depending on the position, raised or lowered. Place glasses in the middle and to the right, dishes to the left, under the cup support rack. Place long and narrow utensils (carving forks, knives) on the bottom of the rack, not crosswise, with the sharp ends pointing inwards towards the appliance. depending on the model B A A B Rack release lever Rack height adjustment: Release the catches (B) of both rack rails. Take the rack out.
PAGE 6
GB Cutlery basket: The cutlery basket has removable inserts into which cutlery should positioned far enough apart so that water can flow between the items. The cutlery basket inserts and central cover can be found in the bag containing accessories. The central cover is simply a lid for the cutlery basket. The inserts can be removed and used separately. Cutlery should be evenly distributed in the basket with the handles pointing downwards; take care not to injure yourself on knives or other sharp items.
PAGE 7
GB WHAT TO DO IF... If a fault occurs, before contacting our After-Sales Service, check the following troubleshooting guide to try and remedy the problem (*see also the corresponding chapter in the user instructions). Problem Cause Remedy The appliance is not working • No water supply. • Turn on the water tap. • The appliance doesn’t fill with enough water. • Clean the filter in the water supply tap. • Ensure the inlet water hose is not kinked. • There is a power failure.
PAGE 8
GB • can be removed • Streaks on the dishes/glasses. • Layer of salt on dishes/glasses. • Reduce the rinse aid setting *. • Close the salt container lid properly *. • not removable • Insufficient water softening, calcium deposits. • Change water hardness setting, if necessary add salt *. Opaque / cloudy glasses • Glasses are not dishwasher-proof. • Use suitable glasses. Rust on cutlery • Not made of stainless steel. • Use suitable cutlery.