Instruction manual AS13.
ELECTRIC SINGLE OVENS USER AND INSTALLATION INSTRUCTIONS DD 29/01/07
For future reference please record the following information which be found on the Rating Plate and the date of purchase which can be found in the invoice: Model Number ……………………. Serial Number ……………………. Date of Purchase …………………….
CONTENTS General Information pages 3-4 Warning and Safety Instructions pages 5-6 Instructions for Use pages 7-15 Instructions for Installation pages 16-21 Maintenance pages 22-23 Technical Data page 24 European directive on Waste Electrical and Electronic Equipment (WEEE) page 25 Conditions of Guarantee page 26
GENERAL INFORMATION Please read this booklet thoroughly before you use this appliance. It is important that you understand all the control functions before commencing to cook with your Baumatic appliance. Please remember the advice and warnings shown on page 5 which is headed ‘IMPORTANT – Warning and Safety Instructions’. This appliance is designed for domestic household use and can be built into a standard kitchen cabinet or housing unit.
The Warranty applies to Great Britain and Northern Ireland only. In the event that you require any After Sales Service or advice, please contact the Baumatic Service Department on telephone number – 0118 933 6911. Before using this appliance ensure that any protective packaging or coatings have been removed. To aid the protection of the environment, please sort the packing materials into different types and dispose of them in accordance with the local waste disposal laws.
IMPORTANT NOTE – WARNING AND SAFETY INSTRUCTIONS Warning: this appliance must be earthed. This appliance complies with all current European safety legislation, however Baumatic do wish to emphasise that compliance does not remove the fact that the appliance surfaces will become hot during use and retain heat after operation.
NOTE: This appliance must be correctly installed by a suitably qualified person, strictly in accordance with the manufacturer’s instructions. For electrical installations, NICEIC registration is recommended. Baumatic Ltd declines any responsibility for injury or damage to persons or property as a result of improper use or installation of this appliance. Please note that this appliance carries the CE mark for normal domestic use and is not suitable for the marine environment.
INSTRUCTIONS FOR USE These User Instructions should be retained for future reference and for use by a person who is perhaps unfamiliar with the appliance. The following models are covered by these instructions: AS13.1SS-A USING THE OVEN The oven is controlled thermostatically between 40°C and 250°C depending on the temperature required. The mode of cooking desired is selected by using the multifunction control knob.
GRILL MODE This is for grilling smaller items of food FAN ASSISTED GRILL MODE This provides quick browning to seal juices in the food. Both the grill and the fan come on. Most of the cooking is done by grilling and the hot hair is circulated around the oven. The oven door should be kept closed. Please preheat the oven for approximately 5 minutes before using. PIZZA FUNCTION This kind of cooking is ideal for pizza and vegetable dishes.
WARNING • • • Ensure that the oven door is kept closed when using the GRILL. Do not use aluminium foil to cover the grill pan or heat Do not wrap items in aluminium foil and place under the grill – the high reflectivity of the foil can damage the grill element. HELPFUL HINTS • • • • • Before cooking, check that any unused accessories are removed from the oven. Preheat the oven at cooking temperature before use.
USING THE ELECTRONIC PROGRAMMER A Temperature B Automatic programme C Duration and manual mode D Minute minder F U N C T I O N Timer Cooking duration time Cooking end time Minus setting Plus setting Setting the clock Switch the oven on (230V). 00.00 will appear in blinking mode on the display. To set the clock, simultaneously press the duration . and end of cooking keys together. Using the +/- keys select the time of day required.
Semiautomatic operation with cooking duration Select cooking duration function and set required duration with the +/- button. “AUTO” (B) and cookpot (C) symbols appear. If time of day= cooking end time the relay output and the cookpot symbol (C) are switched off. The audible signal sounds. The symbol “AUTO” (B) blinks. The cooking will be finished. Semiautomatic operation with cooking end time Select cooking end time function and set required end time using the “+” and “-” keys.
At 13.15 h. (14.00 h. minus 45 minutes ) the oven turns on automatically. During cooking time the cookpot button (C) and “AUTO” (B) switch on. At 14.00 h. the oven turns off automatically, “AUTO” (B) flashes. The cookpot button (C) switches off and a buzzer goes on until it is stopped. Minute counter Select the minute counter function . The fixed time is set at 5 min.; to change it, press the keys +/-.
Switch functions The following functions can be set by turning the switch knob. The following will be shown on the display: Light 190°C 50°C 190°C 250°C 165°C 165°C 165°C Defrost The temperature shown on the display can be changed via the keys +/-. Increase or decrease is in 5°C steps, from a minimum of 40°C to a maximum of 250°C. The symbol °C will blink until the required temperature is reached.
CLEANING THE APPLIANCE Always allow the appliance to cool down before cleaning to avoid a burn injury. Do not use caustic or abrasive agents, coarse wire wool or hard tools as these can damage the surface finishes. Normally, wiping with a soft cloth dampened with hot detergent is sufficient, but for stubborn marks the following is recommended: VITREOUS ENAMEL PARTS Use only a cleaner that is recommended for this type of material – avoid chloride-based products such as bleach.
REMOVING THE OVEN DOOR To facilitate cleaning inside the oven, the door can be removed as follows: Hinges “A” are provided with two movable bolts “B”. When bolt “B” is raised, the hinge is released from its housing. Having done this, the door must be lifted upwards and removed, sliding it towards the outside; grip the sides of the door near the hinges when performing these operations. To refit the door, firstly slide the hinges into their slots and open the door fully.
INSTRUCTIONS FOR INSTALLATION This appliance must be installed by a competent person, in accordance with the current version of the following UK Regulations and Safety Standards or their European Norm replacements: Building Regulations (issued by the Department of Environment) Building Standards (issued by the Scottish Development Department) IEE Wiring Regulations Electricity at Work Regulations PRE-COMMISSIONING THE APPLIANCE When unpacked, check that the following parts are included with the appliance: •
INSTALLATION NOTES 1. Ensure that the aperture for oven installation is the correct size as per Fig. 2 page 18. 2. Ensure that the rear panel of the furniture housing has been removed. 3. All ovens with which this instruction book is provided may be installed without the need for any additional ventilation cutouts. 4. Ensure that the oven has been securely fixed into the housing. The fixing of the oven in the cabinet is made by 4 screws “A” That on the corner of the oven door-frame.
Fig.
Fig. 3: Ventilation and cut-out requirements for installation of a single electric oven into a standard kitchen unit. Fig. 4: Ventilation and cut-out requirements for installation of a Single electric oven into a tall housing unit.
INSTALLATION AS13SS-A 20
ELECTRICAL CONNECTIONS The installation must be carried out by a suitably qualified person, in accordance with the current version of the following. o UK Regulations and Safety Standards or their European Norm Replacements. o Building Regulations (issued by the Department of the Environment). o Building Standards (issued by the Scottish Development Department). o IEE Wiring Regulations. o Electricity At Work Regulations.
REPLACING THE MAINS LEAD In the event it is necessary to replace the mains supply lead, proceed as follows: 1. Disconnect the appliance from the supply, undo the fixing screws and remove the back panel. 2. Undo the clamp screws and terminal screws to release the existing lead. 3. Assemble the replacement lead that must conform to the specification listed in the Technical Data, ensuring the correct colour code connection and that all screws are tightened correctly.
REPLACING THE OVEN LIGHT (Not covered by the appliance warranty) Disconnect the appliance from the electricity supply, remove the oven door (as described previously) as well as the oven shelves. Remove the protective glass lightcover by twisting anti-clockwise. Unscrew the old bulb and discard safely, replace with the type specified in the Technical Data and refit the cover. NOTE – The glass cover may be tight and may therefore require a tight grip to release.
TECHNICAL DATA DIMENSIONS Height: Width: Depth: 591mm 597mm 525mm COOLING FAN A tangential cooling fan is fitted on the following models: AS13, AS13.1, B191 ELECTRICAL DETAILS Rated Voltage: 230V a.c. 50Hz Supply Connection: 16A (double pole switched fused outlet with 3mm contact gap) Max Rated Inputs: AS13, AS13.1, B191: 3,68 kW Mains supply lead: 3x 1.
European directive on Waste Electrical and Electronic Equipment (WEEE) This appliance is marked according to the European directive 2002/96/EC on Waste electrical and Electronic Equipment (WEEE). By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.
Baumatic Ltd. Conditions of guarantee Dear Customer, Your new Baumatic appliance comes complete with a free 12 month guarantee covering both parts and labour costs resulting from defective materials or workmanship. Baumatic also gives you the opportunity to automatically extend the guarantee period for a further 12 months at no extra cost, giving an initial guarantee period of 24 months. The extended guarantee period applies to England, Scotland, Wales and Northern Ireland only.
Headquarters Baumatic Ltd. Baumatic Buildings, 6 Bennet Road, Reading, Berkshire RG2 0QX, United Kingdom Sales Telephone +44 118 933 6900 Sales Fax +44 118 931 0035 Service Telephone +44 118 933 6911 Service Fax +44 118 986 9124 Spares Telephone +44 118 933 6922 Technical / Advice Telephone +44 118 933 6933 E-mail: sales@baumatic.co.uk technical@baumatic.co.uk Http (Internet site): www.baumatic.
Baumatic www.baumatic.
