B17.5SS 90 cm 5 burner gas hob B17.
User Manual for your Baumatic B17.5SS 5 burner gas hob B17.6SS 6 burner gas hob NOTE: This User Instruction Manual contains important information, including safety & installation points, which will enable you to get the most out of your appliance. Please keep it in a safe place so that it is easily available for future reference; for you or any person not familiar with the operation of the appliance.
Contents Environmental note 4 Important safety information 5–7 Specifications Product & aperture dimensions Product specifications Standard accessories Optional extra Electrical details Gas details Gas hob surface layout 8 8 8 8 8 9 9 9 - 10 Using the gas hob Before first use Turning the hob on Automatic electric ignition Energy saving tips 10 10 10 11 11 Cleaning Cleaning the hob top After each use Cleaning the hob burners 12 12 12 12 – 13 Installation Positioning Unpacking the appliance Installi
Environmental note o The packaging materials that Baumatic uses are environmentally friendly and can be recycled. o Please discard all packaging material with due regard for the environment.
Important safety information Your safety is of the utmost importance to Baumatic. Please make sure that you read this instruction booklet before attempting to install or use the appliance. If you are unsure of any of the information contained in this booklet, please contact the Baumatic Technical Department. General Information o This appliance is designed for domestic household use and for the cooking and frying of domestic foodstuffs.
Child Safety o Baumatic strongly recommend that babies and young children are prevented from being near to the appliance and not allowed to touch the appliance at any time. During and after use, all surfaces will become hot. o If it is necessary for younger family members to be in the kitchen, please ensure that they are kept under close supervision at all times. o Older children should only be allowed to utilise the appliance when supervised.
o Great care should be taken whilst using this appliance and when following the cleaning procedure. o You should not use a steam jet or any other high pressure cleaning equipment to clean the appliance. Installation This appliance must be correctly installed by a CORGI registered installer, strictly in accordance with the manufacturer’s instructions and the relevant British Standards. Please see the specific section of this booklet that refers to installation. o Baumatic Ltd.
Specifications Product dimensions: Height: Width: Depth: 510 mm 860 mm 40 mm Aperture dimensions: Height: Width: 480 mm 830 mm Product specifications: o o o o o o o o o 1 x 3.30 kW wok burner 1 x 3.00 kW rapid burner 2 x 1.75 kW semi-rapid burners 1 x 1.00 kW auxiliary burner 2 x 3.00 kW rapid burners 3 x 1.75 kW semi-rapid burners Side control operation Heavy duty cast iron pan stands Underknob auto-ignition (B17.5SS) (B17.5SS) (B17.5SS) (B17.6SS) (B17.
Electrical details Rated Voltage: Supply Connection: Max Rated Inputs: Mains Supply Lead: 230 Vac 50 Hz 3 A (double pole switched fused outlet with 3mm contact gap) 0.008 to 0.02 kW (depending on model) 3 core x 0.75mm² (Type RR-F marked) Gas details Connection: Type: Rp ½ (ISO R7) Natural Gas (20.9 mbar) Alternative LPG G30 (28-30 mbar), Town gas G110 – 120 (8 mbar) to order.
B17.6SS Using the gas hob Before first use IMPORTANT: You should clean the hob surface (see “Cleaning and maintenance” section). Turning the hob on The following symbols will appear on the control panel, next to each control knob: Black circle: gas off Large flame: maximum setting Small flame: minimum setting o The minimum setting is at the end of the anti-clockwise rotation of the control knob. o All operation positions must be selected between the maximum and minimum position.
Automatic electric ignition To ignite a burner: o Press in the control knob of the burner that you wish to light and turn it anti-clockwise to the maximum position. o If you keep the control knob depressed, the automatic ignition for the burner will operate. o Once the burner is lit, turn the control knob to your required setting between the maximum and minimum setting symbols. o In case of power failure, the burners can be lit by carefully using a match.
Cleaning Cleaning operations must only be carried out when the hob is cool. The appliance should be disconnected from your mains supply before commencing any cleaning process. Cleaning the hob top Any residues that are left on the hob top surface from cleaning agents will damage it. You should remove any residues with warm soapy water. Abrasive cleaners or sharp objects will damage the hob surface; you should clean it using warm soapy water.
o IMPORTANT: Make sure that you reassemble the burners in the original way. Installation The installation must be carried out by a CORGI registered installer, in accordance with the current version of the following.
Positioning The adjacent furniture must be able to withstand a minimum temperature rise of 85°C above the ambient temperature of the room it is located in, during periods of use. o This appliance can be located in a kitchen, a kitchen diner or a bed sitting room. IMPORTANT: The appliance must not be installed in a bathroom or shower room.
Unpacking the appliance When unpacking the appliance please check that the following items are contained within the packaging: 1 x Baumatic hob 3 x Pan supports 6 x Burner assemblies 1 x Installation and instruction manual 1 x Baumatic guarantee card 4 x Fixing screws 4 x Clamps 1 x Sealing strip 6 x LPG jets 1 x Self-adhesive label for amending the Gas Category on the appliance’s rating plate (required if the LPG conversion kit is used).
o Carefully turn the hob upside down and place it on a cushioned mat. o Apply the sealing strip (A) provided around the edge of the appliance. o The protective covering must be removed from both sides. o Do not leave a gap in the sealing agent or overlap the thickness. o IMPORTANT: Do not use a silicon sealant to seal the appliance against the aperture. This will make it difficult to remove the hob from the aperture in future, particularly if it needs to be serviced.
o Place the clamp (B) over the holes that match the size of the screws. There are one set of screw holes in each corner of the hob. Slightly tighten a screw (C) through the clamp (B) so that the clamp is attached to the hob, but so that you can still adjust the position of it. o Carefully turn the hob back over and then gently lower it into the aperture hole that you have cut out. o On the underneath of the hob, adjust the clamps into a position that is suitable for your worktop.
Ventilation requirements o The room containing the hob should have an air supply in accordance with the current edition of BS 5440: Part 2: o The room must have opening windows or equivalent; some rooms may also require a permanent vent. o If the room has a volume between 5 and 10m³, it will require an air vent of 50cm² (effective area). Unless it has a door which opens directly to the outside. o If the room has a volume of less than 5m³, it will require an air vent of 100cm² (effective area).
Gas Safety (Installation and Use) Regulations IMPORTANT: The appliance MUST be connected to the gas supply by use of a ½ BSP Elbow, seal, copper pipe and an isolation tap fitted in an easily accessible position. o It is the law that all gas appliances are installed by competent persons in accordance with the current edition of the Gas Safety Installation and Use Regulations. o It is in your interest and that of safety to ensure compliance with the law.
Gas adjustment (Conversion to LPG) All work must be carried out by a CORGI registered engineer. IMPORTANT: Always isolate the cooker from the electricity supply before changing the injectors and/or adjusting the minimum flow of the burners. o Remove the pan-stands, burners and flame spreaders (A). o Unscrew the injector (B) and replace it with the stipulated injector for the new gas supply (see table below).
Minimum flow adjustment for hob gas taps. All work must be carried out by a CORGI registered engineer. IMPORTANT: Always isolate the hob from the electricity supply before changing the injectors and/or adjusting the minimum flow of the burners. o Switch the burner on and set the knob at the minimum position. o Remove the knob from the tap and place a small bladed screwdriver in the centre of the tap shaft.
Gas tap maintenance These maintenance operations MUST ONLY be carried out by a CORGI registered engineer. IMPORTANT: Before carrying out any maintenance operations, disconnect the appliance from the gas and electricity supplies. If a gas tap becomes stiff to operate, then you should proceed as follows: o Remove the control knobs, pan supports, burners, hob fixing screws and clamps. o Remove the hob from the worktop and remove any underside protective covers.
Electrical connection This appliance must be installed by a qualified person in accordance with the latest edition of the I.E.E. Regulations and in compliance with Baumatic’s instructions. Before connecting the appliance, make sure that the supply voltage marked on the rating plate corresponds with your mains supply voltage. o Cable type: 3 core x 0.75mm² (Type RR-F marked). o The mains supply cable is supplied with this product.
My appliance isn’t working correctly IMPORTANT: If your appliance appears not to be operating correctly, then you should disconnect it from your mains supply and then contact the Baumatic Service Department on telephone number (0118) 933 6911. DO NOT ATTEMPT TO REPAIR THE APPLIANCE YOURSELF. Please note that if an engineer is asked to attend whilst the product is under guarantee and finds that the problem is not the result of an appliance fault, then you may be liable for the cost of the call out charge.
United Kingdom Baumatic Ltd., Baumatic Buildings, 6 Bennet Road, Reading, Berkshire RG2 0QX United Kingdom Sales Telephone (0118) 933 6900 Sales Fax (0118) 931 0035 Service Telephone (0118) 933 6911 Service Fax (0118) 986 9124 Spares Telephone (01235) 437244 Technical Advice Telephone (0118) 933 6933 E-mail: sales@baumatic.co.uk technical@baumatic.co.uk Website: www.baumatic.co.uk Republic of Ireland 01- 6266 798 Czech Republic Baumatic CR spol s.r.o.
