B47SS/BG60/BG61/B60.1SS/ BT61SS 4 burner gas hob. BG60TC 4 burner gas hob with thermocouples.
User Manual for your Baumatic B47SS 4 burner gas hob BG60 4 burner gas hob BG61 4 burner gas hob. B60.1SS 4 burner gas hob. BT61SS 4 burner gas hob BG60TC 4 burner gas hob with thermocouples NOTE: This User Instruction Manual contains important information, including safety & installation points, which will enable you to get the most out of your appliance.
Contents Environmental note 4 Important safety information 5–7 Specifications Product & Aperture dimensions Product specifications Standard accessories Optional extras Electrical details Gas details Gas hob surface layout 8 8 8 8 8 8 9 9 Using the gas hob Before first use Turning the hob on Turning the hob on (BG60TC) Energy saving tips 10 10 10 – 11 11 11 – 12 Cleaning Cleaning the hob top After each use Cleaning the hob burners 12 12 12 13 Installation Positioning Unpacking the appliance Install
Environmental note o The packaging materials that Baumatic uses are environmentally friendly and can be recycled. o Please discard all packaging material with due regard for the environment.
Important safety information Your safety is of the utmost importance to Baumatic. Please make sure that you read this instruction booklet before attempting to install or use the appliance. If you are unsure of any of the information contained in this booklet, please contact the Baumatic Technical Department. General Information o This appliance is designed for domestic household use and for the cooking and frying of domestic foodstuffs.
Child Safety o Baumatic strongly recommend that babies and young children are prevented from being near to the appliance and not allowed to touch the appliance at any time. During and after use, all surfaces will become hot. o If it is necessary for younger family members to be in the kitchen, please ensure that they are kept under close supervision at all times. o Older children should only be allowed to utilise the appliance when supervised.
o Great care should be taken whilst using this appliance and when following the cleaning procedure. o You should not use a steam jet or any other high pressure cleaning equipment to clean the appliance. Installation This appliance must be correctly installed by a CORGI registered installer, strictly in accordance with the manufacturer’s instructions and the relevant British Standards. Please see the specific section of this booklet that refers to installation. o Baumatic Ltd.
Specifications Product dimensions: Aperture dimensions: Height: Width: Depth: Height: Width: 500 mm 585 mm 35 mm 480 mm 560 mm Product specifications: o o o o o o o o o 1 x 3.00 kW rapid burner (B47, BG60, BG60TC & B60.1SS) 1 x 3.30 kW wok burner (BG61SS & BT61SS) 2 x 1.75 kW semi-rapid burners 1 x 1.00 kW auxillary burner Side control operation Enamelled pan stands (B47, BG60, BG60TC & BG61SS) Heavy duty cast iron pan stands (B60.
Gas details Connection: Type: Rp ½ (ISO R7) Natural Gas (20.9 mbar), alternative LPG G30 (28-30 mbar), town gas G110 – 120 (8 mbar) to order. For future reference please record the following information which can be found on the rating plate and the date of purchase which can be found on your sales invoice. The rating plate of your hob is located on the underneath of the appliance. Therefore it is a good idea to record this information before you install your appliance. Model Number ……………………………….
Using the gas hob Before first use IMPORTANT: You should clean the hob surface (see “Cleaning and maintenance” section). Turning the hob on The following symbols will appear on the control panel, next to each control knob: Black circle: gas off Large flame: maximum setting Small flame: minimum setting o The minimum setting is at the end of the anti-clockwise rotation of the control knob. o All operation positions must be selected between the maximum and minimum position.
o In case of power failure, the burners can be lit by carefully using a match. Turning the hob on (BG60TC only) o This particular appliance is fitted with a thermocouple safety device on each burner, which is designed to stop the flow of gas to the burner head in the event of the flame going out. o To light a burner, press in and turn the appropriate control knob anti-clockwise to the large flame symbol.
o Use flat bottomed pans only o When possible, keep a lid on the pan whilst cooking. o Cook vegetables with as little water as possible, to reduce cooking times. IMPORTANT: Always place pans centrally over the hob burners and position them so that the handles cannot get accidentally caught or knocked off. You should also make sure that the handle is not over one of the other hob burner flames. Cleaning Cleaning operations must only be carried out when the hob is cool.
Cleaning the hob burners The hob burners should be cleaned once a week or more frequently if they get soiled. o IMPORTANT: Make sure that the hob surface, pan supports and hob burners have cooled before you attempt to touch them. o Remove the hob burners by pulling them upwards and away from the hob top. o Soak them for about ten minutes in hot water and a little detergent. o After cleaning and washing them, wipe and dry them carefully.
Positioning The adjacent furniture must be able to withstand a minimum temperature rise of 85°C above the ambient temperature of the room it is located in, during periods of use. o This appliance can be located in a kitchen, a kitchen diner or a bed sitting room. IMPORTANT: The appliance must not be installed in a bathroom or shower room.
Unpacking the appliance When unpacking the appliance please check that the following items are contained within the packaging: 1 x Baumatic hob 2 x Pan supports 4 x Burner assemblies 1 x Installation and instruction manual 1 x Baumatic guarantee card 4 x Fixing screws 4 x Clamps 1 x Sealing strip 4 x LPG jets 1 x Self-adhesive label for amending the Gas Category on the appliance’s rating plate (required if the LPG conversion kit is used).
o Carefully turn the hob upside down and place it on a cushioned mat. o Apply the sealing strip (A) provided around the edge of the appliance. o The protective covering must be removed from both sides. o Do not leave a gap in the sealing agent or overlap the thickness. o IMPORTANT: Do not use a silicon sealant to seal the appliance against the aperture. This will make it difficult to remove the hob from the aperture in future, particularly if it needs to be serviced.
o Place the clamp (B) over the holes that match the size of the screws. There are one set of screw holes in each corner of the hob. Slightly tighten a screw (C) through the clamp (B) so that the clamp is attached to the hob, but so that you can still adjust the position of it. o Carefully turn the hob back over and then gently lower it into the aperture hole that you have cut out. o On the underneath of the hob, adjust the clamps into a position that is suitable for your worktop.
Ventilation requirements o The room containing the cooker should have an air supply in accordance with the current edition of BS 5440: Part 2: o The room must have opening windows or equivalent; some rooms may also require a permanent vent. o If the room has a volume between 5 and 10m³, it will require an air vent of 50cm² (effective area). Unless it has a door which opens directly to the outside. o If the room has a volume of less than 5m³, it will require an air vent of 100cm² (effective area).
o In the UK, CORGI registered installers work to safe standards of practice. The cooker must also be installed in accordance with the current edition of BS 6172. Failure to install the cooker correctly could invalidate the warranty, liability claims and lead to prosecution. o Put the gas seal into the elbow. o Fully tighten the elbow and seal onto the gas rail. o The elbow MUST be pointing in a downwards direction. o Gas pressure may be checked on a semi-rapid hob burner.
o Unscrew the injector (B) and replace it with the stipulated injector for the new gas supply (see table below). o Reassemble all the burners carefully; in particular you should make sure that the flame spreader is correctly placed on the burner. Gas tap maintenance These maintenance operations MUST ONLY be carried out by a CORGI registered engineer. IMPORTANT: Before carrying out any maintenance operations, disconnect the appliance from the gas and electricity supplies.
o Lightly smear the cone with high temperature grease, reassemble into position and rotate a few times. o Remove the cone again and remove any excess grease, making sure that the gas ducts are not obstructed with grease. o Carefully reassemble the components and perform a gas soundness test. If it becomes necessary to replace a gas tap, then you should proceed as follows: o Remove the control knobs, pan supports, burners, hob fixing screws and clamps.
Replacing the mains supply cable If the mains supply cable is damaged, then it must be replaced by an appropriate replacement which can be obtained from the Baumatic Spares Department. The mains supply cable should be replaced in accordance with the following instructions: o Switch the appliance off at the control switch. o Open the box of the supply board. o Unscrew the clamp (A) fixing the cable. o Replace the cable with one of the same length and in accordance with the specification given above.
My appliance isn’t working correctly IMPORTANT: If your appliance appears not to be operating correctly, then you should disconnect it from your mains supply and then contact the Baumatic Service Department on telephone number (0118) 933 6911. DO NOT ATTEMPT TO REPAIR THE APPLIANCE YOURSELF. Please note that if an engineer is asked to attend whilst the product is under guarantee and finds that the problem is not the result of an appliance fault, then you may be liable for the cost of the call out charge.
Baumatic Ltd. Conditions of Guarantee Dear Customer, Your new Baumatic appliance comes complete with a free 12 month guarantee covering both parts and labour costs resulting from defective materials or workmanship. Baumatic also gives you the opportunity to automatically extend the guarantee period for a further 12 months at no extra cost, giving an initial guarantee period of 24 months. The extended guarantee period applies to England, Scotland, Wales and Northern Ireland only.
Baumatic Ltd You will be mine Headquarters Baumatic Ltd. Baumatic Buildings, 6 Bennet Road, Reading, Berkshire RG2 0QX, United Kingdom Sales Telephone +44 118 933 6900 Sales Fax +44 118 931 0035 Service Telephone +44 118 933 6911 Service Fax +44 118 986 9124 Spares Telephone +44 118 933 6922 Technical / Advice Telephone +44 118 933 6933 E-mail: sales@baumatic.co.uk technical@baumatic.co.uk Http (Internet site): www.baumatic.
