B46.1SS/B46.1TCSS/B60.3SS/ BT61.1SS/BT62.1SS/ BT62.1TCSS/BG67.1SS/ B68.1SS/B68.1TCSS/B17.
User Manual for your Baumatic B46.1SS 60 cm 4 Burner gas hob B46.1TCSS 60 cm 4 Burner gas hob with thermocouples B60.3SS 60 cm 4 Burner gas hob with thermocouples BT61.1SS 60 cm 4 Burner gas hob with thermocouples BT62.1SS 60 cm 4 Burner gas hob BT62.1TCSS 60 cm 4 Burner gas hob with thermocouples BG67.1SS 70 cm 5 Burner gas hob with thermocouples B68.1SS 70 cm 5 Burner gas hob B68.1TCSS 70 cm 5 burner gas hob with thermocouples B17.
Contents Environmental note 4 Important safety information 5–7 Specifications B46.1SS/B46.1TCSS B60.3SS BT61.1SS BT62.1SS/BT62.1TCSS BG67.1SS B68.1SS/B68.1TCSS B17.8SS Electrical details Gas details Gas hob surface layout 8 – 17 8 9 10 11 12 13 14 15 15 15 - 17 Using the gas hob Before first use Switching the hob on Pushbutton ignition (B46.1SS) Pushbutton ignition with flame failure device (B46.1TCSS/B60.3SS/BT61.1SS) Automatic ignition (B68.1SS/BT62.
Environmental note o The packaging materials that Baumatic uses are environmentally friendly and can be recycled. o Please discard all packaging material with due regard for the environment.
Important safety information Your safety is of the utmost importance to Baumatic. Please make sure that you read this instruction booklet before attempting to install or use the appliance. If you are unsure of any of the information contained in this booklet, please contact the Baumatic Advice Line. General Information o This appliance is designed for domestic household use and for the cooking and frying of domestic foodstuffs.
Child Safety o Baumatic strongly recommend that babies and young children are prevented from being near to the appliance and not allowed to touch the appliance at any time. During and after use, all surfaces will be hot. o If it is necessary for younger family members to be in the kitchen, please ensure that they are kept under close supervision at all times. o Older children should only be allowed to utilise the appliance when supervised.
Cleaning o Cleaning of the hob should be carried out on a regular basis. o IMPORTANT: Before attempting to clean the appliance, it should be disconnected from the mains and cool. o Great care should be taken whilst using this appliance and when following the cleaning procedure. o You should not use a steam jet or any other high pressure cleaning equipment to clean the appliance.
Specifications B46.1SS/B46.1TCSS Product dimensions: Aperture dimensions: Height: Width: Depth: Height: Width: 500 mm 585 mm 35 mm 480 mm 560 mm Product specifications: o 1 x 3.00 kW rapid burner o 2 x 1.75 kW semi-rapid burners o 1 x 1.00 kW auxiliary burner o o o o Side control operation Pushbutton ignition Enamelled pan stands Flame failure safety device on each burner (B46.
B60.3SS Product dimensions: Aperture dimensions: Height: Width: Depth: Height: Width: 500 mm 585 mm 35 mm 480 mm 560 mm Product specifications: o 1 x 3.00 kW rapid burner o 2 x 1.75 kW semi-rapid burners o 1 x 1.
BT61.1SS Product dimensions: Aperture dimensions: Depth: Width: Height: Depth: Width: 500 mm 585 mm 35 mm 480 mm 560 mm Product specifications: o 1 x 3.30 kW triple crown (wok) burner o 2 x 1.75 kW semi-rapid burners o 1 x 1.
BT62.1SS/BT62.1TCSS Product dimensions: Aperture dimensions: Depth: Width: Height: Depth: Width: 500 mm 585 mm 35 mm 480 mm 560 mm Product specifications: o 1 x 3.30 kW triple crown (wok) burner o 2 x 1.75 kW semi-rapid burners o 1 x 1.00 kW auxiliary burner o o o o Front control operation Automatic ignition Heavy duty cast iron pan stands Flame failure safety device on each burner (BT62.
BG67.1SS Product dimensions: Aperture dimensions: Depth: Width: Height: Depth: Width: o o o o 1 1 2 1 510 mm 685 mm 35 mm x x x x 3.30 3.00 1.75 1.
B68.1SS/B68.1TCSS Product dimensions: Aperture dimensions: Depth: Width: Height: Depth: Width: o o o o 1 1 2 1 510 mm 685 mm 35 mm x x x x 3.30 3.00 1.75 1.00 kW kW kW kW 480 mm 560 mm triple crown (wok) burner rapid burner semi-rapid burners auxiliary burner o Front control operation o Automatic ignition o Flame failure safety device on each burner (B68.
B17.8SS Product dimensions: Aperture dimensions: Depth: Width: Height: Depth: Width: 510 mm 860 mm 40 mm 480 mm 830 mm Product specifications: x x x x 3.30 3.00 1.75 1.
Electrical details Rated Voltage: Supply Connection: Max Rated Inputs: Mains Supply Lead: 230 Vac 50 Hz 3 A (double pole switched fused outlet with 3mm contact gap) 0.008 to 0.02 kW (depending on model) 3 core x 0.75mm² (Type RR-F marked) Gas details Connection: Type: Rp ½ (ISO R7) Natural Gas (20.
BT61.1SS A = 3.30 kW wok burner B = 1.75 kW semi-rapid burner C = 1.00 kW auxiliary burner D = Control panel E = Ignition button BT62.1SS/BT62.1TCSS A = 3.30 kW wok burner B = 1.75 kW semi-rapid burner C = 1.00 kW auxiliary burner D = Control panel BG67.1SS/B68.1SS/B68.1TCSS A = 3.30 kW wok burner B = 3.00 kW rapid burner C = 1.75 kW semi-rapid burner D = 1.
B17.8SS A = 3.30 kW wok burner B = 3.00 kW rapid burner C = 1.75 kW semi-rapid burner D = 1.00 kW auxiliary burner Using the gas hob Before first use IMPORTANT: You should clean the hob surface (see “Cleaning and maintenance” section). Switching the hob on The following symbols will appear on the control panel, next to each control knob: = gas off Large flame: maximum setting Small flame: minimum setting o The minimum setting is at the end of the anti-clockwise rotation of the control knob.
o Never select a knob position between the maximum and off position. o The symbol on the control panel, next to the control knob will indicate which gas burner it operates. Pushbutton ignition (B46.1SS) o Press in and turn the appropriate control knob anti-clockwise to the large flame symbol. o Whilst pressing in the control knob, press and hold down the ignition button, which is located on the control panel.
o To switch the burner off, turn the control knob fully clockwise to the gas off position. o In case of power failure, the burners can be lit by carefully using a match. Automatic ignition (BT62.1SS/B68.1SS) To ignite a burner: o Press in the control knob of the burner that you wish to light and turn it anti-clockwise to the maximum position. o If you keep the control knob depressed, the automatic ignition for the burner will operate.
o In case of power failure, the burners can be lit by carefully using a match. Energy saving tips BURNERS PANS Minimum Maximum diametre diametre Wok 220 mm 260 mm Rapid 180 mm 220 mm Semi-rapid 120 mm 200 mm Auxiliary 80 mm 160 mm o The diametre of the bottom of the pan should correspond to that of the burner. o The burner flame must never extend beyond the diametre of the pan. o Use flat bottomed pans only o When possible, keep a lid on the pan whilst cooking.
Cleaning the hob top Any residues that are left on the hob top surface from cleaning agents will damage it. You should remove any residues with warm soapy water. Abrasive cleaners or sharp objects will damage the hob surface; you should clean it using warm soapy water. Although it is easier to clean some deposits whilst the hob surface is still warm. Make sure that the hob surface, pan supports and hob burners have all cooled sufficiently before you attempt to touch them.
Maintaining the cast iron pan stands o IMPORTANT: Make sure that the hob surface and pan stands have cooled before you attempt to touch them. o Wipe the pan stands over with a soft, damp cloth that has been put into warm soapy water. The cloth should be wrung out after being taken out of the soapy water. o Using a paper towel, thoroughly dry the pan stands.
Positioning The adjacent furniture must be able to withstand a minimum temperature rise of 85°C above the ambient temperature of the room it is located in, during periods of use. * 600 mm (B46.1SS, B46.1TCSS, B60.3SS, BT61.1SS, BT62.1SS, BT62.1TCSS) * 700 mm (BG67.1SS, B68.1SS, B68.1TCSS) * 900 mm (B17.8SS) o This appliance can be located in a kitchen, a kitchen diner or a bed sitting room. IMPORTANT: The appliance must not be installed in a bathroom or shower room.
o 400 mm between the hob surface, providing that the underside of the horizontal surface is in line with the outer edge of the hob. If the underside of the horizontal surface is lower than 400 mm, then it must be at least 50 mm away from the outer edges of the hob. o 50 mm clearance around the appliance and between the hob surface and any combustible materials.
BG67.1SS B68.1SS B68.1TCSS B17.8SS o Cut a hole in the worktop that corresponds with the relevant drawing for your hob on pages 24 - 25. All models (except B17.8SS) B17.8SS o IMPORTANT: You must have a gap of at least 25 mm between the underneath of the appliance and any surface that is below it.
o Carefully turn the hob upside down and place it on a cushioned mat. o Apply the sealing strip (A) provided around the edge of the appliance. o The protective covering must be removed from both sides. o Do not leave a gap in the sealing agent or overlap the thickness. o IMPORTANT: Do not use a silicon sealant to seal the appliance against the aperture. This will make it difficult to remove the hob from the aperture in future if it needs to be serviced.
o On the underneath of the hob, adjust the clamps into a position that is suitable for your worktop. Then fully tighten the screws (C) to secure the hob into position. Gas connection This appliance must be installed by a competent person in accordance with the current versions of the following UK (United Kingdom) or ROI (Republic of Ireland) Regulations and Safety Standards or their European Norm Replacements.
o If it is installed in a room with a volume that exceeds 11m³, then no air vent is required. o If there are any other fuel burning appliances in the same room the current edition of BS 5440: Part 2: should be consulted to determine air vent requirements. o Ensure that the room containing the hob is well ventilated, keep natural ventilation holes or install a mechanical ventilation device (mechanical cooker hood).
o Put the gas seal into the elbow. o Fully tighten the elbow and seal onto the gas rail. o The elbow MUST be pointing in a downwards direction. o Gas pressure may be checked on a semi-rapid hob burner. Remove the appropriate injector and attach a test nipple. Light the other burners and observe that the gas pressure complies with the gas standards in force. o IMPORTANT: On completion carry out a gas soundness test. Gas adjustment (Conversion to LPG) All work must be registered engineer.
o Unscrew the injector (B) and replace it with the stipulated injector for the new gas supply (see table below). GENERAL INJECTORS Kind of gas Nozzle Burners mm/100 Natural 135 Wok 115 Rapid 97 Semi-rapid 72 Auxiliary L.P.G. 95 Wok Butane 85 Rapid Propane 65 Semi-rapid 50 Auxiliary TABLE Power (in watts) Max. Min.
Minimum flow adjustment for hob gas taps. All work must be registered engineer. carried out by a GASSAFE IMPORTANT: Always isolate the hob from the electricity supply before changing the injectors and/or adjusting the minimum flow of the burners. o Switch the burner on and set the knob at the minimum position. o Remove the knob from the tap and place a small bladed screwdriver in the centre of the tap shaft.
Gas tap maintenance These maintenance operations MUST ONLY be carried out by a GASSAFE registered engineer. IMPORTANT: Before carrying out any maintenance operations, disconnect the appliance from the gas and electricity supplies. If a gas tap becomes stiff to operate, then you should proceed as follows: o Remove the control knobs, pan supports, burners, hob fixing screws and clamps. o Remove the hob from the worktop and remove any underside protective covers.
o Reconnect the gas tap, perform a gas soundness test and then reassemble the hob. Electrical connection This appliance must be installed by a qualified person in accordance with the latest edition of the I.E.E. Regulations and in compliance with Baumatic’s instructions. Before connecting the appliance, make sure that the supply voltage marked on the rating plate corresponds with your mains supply voltage. o Cable type: H05 RRF 3 core x 0.75 mm³ (Type RR-F marked).
My appliance isn’t working correctly IMPORTANT: If your appliance appears not to be operating correctly, then you should disconnect it from your mains supply and then contact the Customer Care Department on telephone number (0118) 933 6911. DO NOT ATTEMPT TO REPAIR THE APPLIANCE YOURSELF. Please note that if an engineer is asked to attend whilst the product is under guarantee and finds that the problem is not the result of an appliance fault, then you may be liable for the cost of the call out charge.
United Kingdom Baumatic Ltd., Baumatic Buildings, 6 Bennet Road, Reading, Berkshire RG2 0QX United Kingdom Sales Telephone (0118) 933 6900 Sales Fax (0118) 931 0035 Customer Care Telephone (0118) 933 6911 Customer Care Fax (0118) 986 9124 Spares Telephone (01235) 437244 Advice Line Telephone (0118) 933 6933 E-mail: sales@baumatic.co.uk customercare@baumatic.co.uk spares@baumatic.co.uk technical@baumatic.co.uk Website: www.baumatic.co.