AS26SS/B26SS/B40/ B70.
User Manual for your Baumatic AS26SS 90 cm 4 Burner gas glass hob with thermocouples B26SS 90 cm 4 Burner gas glass hob with thermocouples B40 Circular Ø 52 cm Frameless glass gas hob B70.
Contents Environmental note 4 Important safety information 5–7 Specifications AS26SS/B26SS B40 B70.1BL B71TCBL B72BL B72TCBL/W B77BL B77TCBL B78BL PHG602 Electrical details Gas details Gas hob surface layout 8 – 20 8 9 10 11 12 13 14 15 16 17 18 18 18 - 20 Using the gas hob Before first use Switching the hob on Automatic ignition (B70.
Environmental note o The packaging materials that Baumatic uses are environmentally friendly and can be recycled. o Please discard all packaging material with due regard for the environment.
Important safety information Your safety is of the utmost importance to Baumatic. Please make sure that you read this instruction booklet before attempting to install or use the appliance. If you are unsure of any of the information contained in this booklet, please contact the Baumatic Advice Line. General Information o This appliance is designed for domestic household use and for the cooking and frying of domestic foodstuffs.
Child Safety o Baumatic strongly recommend that babies and young children are prevented from being near to the appliance and not allowed to touch the appliance at any time. During and after use, all surfaces will be hot. o If it is necessary for younger family members to be in the kitchen, please ensure that they are kept under close supervision at all times. o Older children should only be allowed to utilise the appliance when supervised.
Cleaning o Cleaning of the hob should be carried out on a regular basis. o IMPORTANT: Before attempting to clean the appliance, it should be disconnected from the mains and cool. o Great care should be taken whilst using this appliance and when following the cleaning procedure. o You should not use a steam jet or any other high pressure cleaning equipment to clean the appliance.
Specifications AS26SS/B26SS Product dimensions: Aperture dimensions: Height: Width: Depth: Height: Width: 350 mm 880 mm 50 mm 335 mm 865 mm Product specifications: o 1 x 3.50 kW rapid burner o 2 x 1.75 kW semi-rapid burners o 1 x 1.
B40 Product dimensions: Aperture dimensions: Width: Height: Width: 520 mm 50 mm 500 mm Product specifications: o 1 x 3.50 kW triple crown (wok) burner o 1 x 3.00 kW rapid burner o 1 x 1.75 kW semi-rapid burner o o o o Front control operation Automatic ignition Flame failure safety device on each burner RANA design cast iron pan stands o IMPORTANT: Not suitable for installation above builtunder ovens due to the location of the gas inlet.
B70.1BL Product dimensions: Aperture dimensions: Depth: Width: Height: Depth: Width: 510 mm 580 mm 50 mm 480 mm 560 mm Product specifications: o 1 x 3.00 kW rapid burner o 2 x 1.75 kW semi-rapid burners o 1 x 1.
B71TCBL Product dimensions: Aperture dimensions: Depth: Width: Height: Depth: Width: 510 mm 580 mm 50 mm 480 mm 560 mm Product specifications: o 1 x 3.00 kW rapid burner o 2 x 1.75 kW semi-rapid burners o 1 x 1.
B72BL Product dimensions: Aperture dimensions: Depth: Width: Height: Depth: Width: 510 mm 580 mm 50 mm 490 mm 560 mm o 1 x 3.50 kW wok burner o 2 x 1.75 kW semi-rapid burners o 1 x 1.
B72TCBL/W Product dimensions: Aperture dimensions: Depth: Width: Height: Depth: Width: 510 mm 580 mm 50 mm 490 mm 560 mm o 1 x 3.50 kW wok burner o 2 x 1.75 kW semi-rapid burners o 1 x 1.
B77BL Product dimensions: Aperture dimensions: Depth: Width: Height: Depth: Width: 510 mm 680 mm 50 mm 490 mm 562 mm Product specifications: o o o o 1 1 2 1 x x x x 3.50 3.00 1.75 1.
B77TCBL Product dimensions: Aperture dimensions: Depth: Width: Height: Depth: Width: 510 mm 680 mm 50 mm 490 mm 562 mm Product specifications: o o o o 1 1 2 1 x x x x 3.50 3.00 1.75 1.
B78BL Product dimensions: Aperture dimensions: Depth: Width: Height: Depth: Width: 510 mm 680 mm 50 mm 490 mm 562 mm Product specifications: o o o o 1 1 2 1 x x x x 3.50 3.00 1.75 1.
PHG602 Product dimensions: Aperture dimensions: Depth: Width: Height: Depth: Width: 510 mm 580 mm 50 mm 490 mm 560 mm Product specifications: o 1 x 3.50 kW wok burner o 2 x 1.75 kW semi-rapid burners o 1 x 1.
Electrical details Rated Voltage: Supply Connection: Max Rated Inputs: Mains Supply Lead: 230 Vac 50 Hz 3 A (double pole switched fused outlet with 3mm contact gap) 0.008 to 0.02 kW (depending on model) 3 core x 0.75mm² (Type RR-F marked) Gas details Connection: Type: Rp ½ (ISO R7) Natural Gas (20.9 mbar), Alternative LPG G30 (28-30 mbar), Town gas G110 – 120 (8 mbar) to order.
B40 A = B = C = burner D = 3.50 kW wok burner 3.00 kW rapid burner 1.75 kW semi-rapid Control panel B70.
B77BL/B77TCBL/B78BL Using the gas hob Before first use IMPORTANT: You should clean the hob surface (see “Cleaning and maintenance” section). Switching the hob on The following symbols will appear on the control panel, next to each control knob: 0 = gas off Large flame: maximum setting Small flame: minimum setting o The minimum setting is at the end of the anti-clockwise rotation of the control knob. o All operation positions must be selected between the maximum and minimum position.
o The symbol on the control panel, next to the control knob will indicate which gas burner it operates. Automatic ignition (B70.1BL, B72BL, B77BL) To ignite a burner: o Press in the control knob of the burner that you wish to light and turn it anti-clockwise to the maximum position. o If you keep the control knob depressed, the automatic ignition for the burner will operate. o Once the burner is lit, turn the control knob to your required setting between the maximum and minimum setting symbols.
o In case of power failure, the burners can be lit by carefully using a match. Energy saving tips BURNERS PANS Minimum Maximum diametre diametre Wok 220 mm 260 mm Rapid 180 mm 220 mm Semi-rapid 120 mm 200 mm Auxiliary 80 mm 160 mm o The diametre of the bottom of the pan should correspond to that of the burner. o The burner flame must never extend beyond the diametre of the pan. o Use flat bottomed pans only o When possible, keep a lid on the pan whilst cooking.
Cleaning Cleaning operations must only be carried out when the hob is cool. The appliance should be disconnected from your mains supply before commencing any cleaning process. Cleaning the hob top Any residues that are left on the hob top surface from cleaning agents will damage it. You should remove any residues with warm soapy water. Abrasive cleaners or sharp objects will damage the hob surface; you should clean it using warm soapy water.
o Before placing the burners back on the hob top, make sure that the gas jet is not blocked. o IMPORTANT: Make sure that you reassemble the burners in the original way. Maintaining the cast iron pan stands o IMPORTANT: Make sure that the hob surface and pan stands have cooled before you attempt to touch them. o Wipe the pan stands over with a soft, damp cloth that has been put into warm soapy water. The cloth should be wrung out after being taken out of the soapy water.
Positioning The adjacent furniture must be able to withstand a minimum temperature rise of 85°C above the ambient temperature of the room it is located in, during periods of use. o This appliance can be located in a kitchen, a kitchen diner or a bed sitting room. IMPORTANT: The appliance must not be installed in a bathroom or shower room.
o 50 mm clearance around the appliance and between the hob surface and any combustible materials. Unpacking the appliance When unpacking the appliance please check that the following items are contained within the packaging: 1 x Baumatic hob 3 x Pan stands (B40) 4 x Pan stands (AS26SS, B26SS, B70.
B70.1BL B71TCBL B72BL B72TCBL/W PHG602 B77BL B77TCBL B78BL o Cut a hole in the worktop that corresponds with the relevant drawing for your hob on pages 26 - 27.
o IMPORTANT: You must have a gap of at least 25 mm between the underneath of the appliance and any surface that is below it. o Carefully turn the hob upside down and place it on a cushioned mat. o Apply the sealing strip (A) provided around the edge of the appliance. o The protective covering must be removed from both sides. o Do not leave a gap in the sealing agent or overlap the thickness. o IMPORTANT: Do not use a silicon sealant to seal the appliance against the aperture.
o Carefully turn the hob back over and then gently lower it into the aperture hole that you have cut out. o On the underneath of the hob, adjust the clamps into a position that is suitable for your worktop. Then fully tighten the screws (C) to secure the hob into position.
o If the room has a volume of less than 5m³, it will require an air vent of 100cm² (effective area). o If it is installed in a room with a volume that exceeds 11m³, then no air vent is required. o If there are any other fuel burning appliances in the same room the current edition of BS 5440: Part 2: should be consulted to determine air vent requirements.
o Put the gas seal into the elbow. o Fully tighten the elbow and seal onto the gas rail. o The elbow MUST be pointing in a downwards direction. o Gas pressure may be checked on a semi-rapid hob burner. Remove the appropriate injector and attach a test nipple. Light the other burners and observe that the gas pressure complies with the gas standards in force. o IMPORTANT: On completion carry out a gas soundness test.
A B C D (not = Gas inlet = Seals = Gas Elbow = Copper pipe supplied) o Put the gas seal into the elbow. o Fully tighten the elbow and seal onto the gas rail. IMPORTANT: The gas elbow must be in the position shown in the above line drawing. o Gas pressure may be checked on a semi-rapid hob burner. Remove the appropriate injector and attach a test nipple. Light the other burners and observe that the gas pressure complies with the gas standards in force.
o Unscrew the injector (B) and replace it with the stipulated injector for the new gas supply (see table below). GENERAL INJECTORS Kind of gas Nozzle Burners mm/100 Natural 135 Wok 115 Rapid 97 Semi-rapid Auxiliary 72 L.P.G. 95 Wok Butane 85 Rapid Propane 65 Semi-rapid 50 Auxiliary TABLE Power (in watts) Max. Min.
Minimum flow adjustment for hob gas taps. All work must be registered engineer. carried out by a GASSAFE IMPORTANT: Always isolate the hob from the electricity supply before changing the injectors and/or adjusting the minimum flow of the burners. o Switch the burner on and set the knob at the minimum position. o Remove the knob from the tap and place a small bladed screwdriver in the centre of the tap shaft.
Gas tap maintenance These maintenance operations MUST ONLY be carried out by a GASSAFE registered engineer. IMPORTANT: Before carrying out any maintenance operations, disconnect the appliance from the gas and electricity supplies. If a gas tap becomes stiff to operate, then you should proceed as follows: o Remove the control knobs, pan supports, burners, hob fixing screws and clamps. o Remove the hob from the worktop and remove any underside protective covers.
o Reconnect the gas tap, perform a gas soundness test and then reassemble the hob. Electrical connection This appliance must be installed by a qualified person in accordance with the latest edition of the I.E.E. Regulations and in compliance with Baumatic’s instructions. Before connecting the appliance, make sure that the supply voltage marked on the rating plate corresponds with your mains supply voltage. o Cable type: H05 RRF 3 core x 0.75 mm³ (Type RR-F marked).
My appliance isn’t working correctly IMPORTANT: If your appliance appears not to be operating correctly, then you should disconnect it from your mains supply and then contact the Customer Care Department on telephone number (0118) 933 6911. DO NOT ATTEMPT TO REPAIR THE APPLIANCE YOURSELF. Please note that if an engineer is asked to attend whilst the product is under guarantee and finds that the problem is not the result of an appliance fault, then you may be liable for the cost of the call out charge.
United Kingdom Baumatic Ltd., Baumatic Buildings, 6 Bennet Road, Reading, Berkshire RG2 0QX United Kingdom Sales Telephone (0118) 933 6900 Sales Fax (0118) 931 0035 Customer Care Telephone (0118) 933 6911 Customer Care Fax (0118) 986 9124 Spares Telephone (01235) 437244 Advice Line Telephone (0118) 933 6933 E-mail: sales@baumatic.co.uk customercare@baumatic.co.uk spares@baumatic.co.uk technical@baumatic.co.uk Website: www.baumatic.co.
