User Manual for your BAH9009G Cooker Hood 90 cm Island Chimney Hood in Stainless Steel NOTE: This User Instruction Manual contains important information, including safety & installation points, which will enable you to get the most out of your appliance. Please keep it in a safe place so that it is easily available for future reference.
CONTENTS YOUR COOKER HOOD’S SPECIFICATIONS ….……………..………….2 IMPORTANT SAFETY INFORMATION……………………………….…3-4 CARING FOR THE ENVIRONMENT…………………………………………5 USING YOUR COOKER HOOD………………………………..……………..6 MAINTAINING AND CLEANING YOUR COOKER HOOD ……….7-9 INSTALLATION INSTRUCTIONS ……………………….……...….10-17 CARBON FILTER …………..10 ELECTRICAL CONNECTION……………11 INSTALLING THE COOKER HOOD….….12-13 INSTALLATION NOTES – EXTRACTION / PURIFYING VERSION .….
Specifications of your LOH9009 Cooker Hood Congratulations on purchasing a Cooker Hood! To fully enjoy using your appliance long into the future, please firstly familiarise yourself with its specifications, safety advice and operational instructions included in this manual. You will also need this manual to ensure that your Cooker Hood has been installed properly.
Important Safety Information: Please Read this before installing & using. o Any installation work must be carried out by a qualified electrician or competent person. o The hood must be installed in accordance with the installation instructions and all measurements followed. o If the cooker hood is installed for use above a gas appliance then the provision for ventilation must be in accordance with the Gas Safety Codes of Practice BS.6172, BS.5440 & BS.6891 (Natural Gas) and BS.
o Ensure the ducting for the extractor function has the same diameter as the outlet hole all the way through. ventilation measures are being observed. Note that it removes odours from your room, not steam. o Keep young children from o Warning - Always ensure that the cooker hood has been disconnected from the power supply before carrying out any work on the hood, including replacing light bulbs. using, playing with or tampering with the cooker hood.
fitted or if the filters are excessively greasy! Never flambé cook under this cooker hood. Environmental Note Note: Before discarding an old appliance, switch off and disconnect it from the power supply. Cut off and render any plug useless. Cut the cable off directly behind the appliance to prevent misuse. This should be undertaken by a competent person. CONFORMITY TO W.E.E.E.
Using your Cooker Hood: To use your cooker hood: 1) Make sure it has been properly installed. 2) Find the CONTROL PANEL. It is located at the front of the canopy. You have a Pushbutton control panel that looks like the one pictured below. 3) The CONTROL PANEL’s buttons all perform separate functions. You will need to understand what these do before you attempt to use your cooker hood. * Note: The hood should be switched on at least as soon as you start cooking. 1.
5. Push the light button; the indicating light 4 on, and the two lighting lamps will come on. Push it again and the lamps will turn off, with every push the buzzer will buzz one time. Cleaning your Cooker Hood: IMPORTANT: Before cleaning, always ensure that you have switched your cooker hood OFF at the power switch, set at the wall from the cable: Cleaning Clean the external parts with mild liquid detergents on a damp cloth. Never use abrasive powder, corrosive solvents or brushes.
To prevent this fire hazard, the grille should be cleaned regularly (depending on use) every 10-15 days and at least once a month in hot water with normal washing-up detergent. DO NOT USE A DISHWASHER TO ACHIEVE THIS. Maintenance - Cleaning the Anti-grease Filters on: Please Read this before installing & using. First remove the grille by pulling down on it. Undo the side catches. You can now clean the anti-grease filter grilles.
Maintenance – Changing the Light Bulb and Carbon Filter a) Changing the light bulb Before changing the light bulb, ensure that the appliance is not live (i.e., ensure that you have switched it off so that it‟s in the „0‟ position). Remove the metal anti-grease filters (see Figure 2 below) and find the old bulb located in the light fixture up inside the exposed canopy. Change the halogen bulb using only halogen spares with a G4 coupling, max. 20W.
* PLEASE NOTE - Defective bulbs should be replaced immediately. Replace the metal anti-grease filters. Installing / Changing the Carbon Filter ______________________________________________________________________________________ Installing / Changing the Carbon Filter. Your Cooker Hood uses CARBON FILTERS to purify the air for the air recirculation function. You will find two filters that will attach to both sides of the fan motor (please see figures at bottom of page).
1) Press the handle of the metal grease filter towards the rear part of the unit until it is released from the front housing, and remove it by pressing downwards (Fig. 2 - above). 2) Remove the old carbon filters by twisting them anticlockwise until they unlatch from the sides of the motor. 3) Place the new carbon filters (which have two fixing tongues), turning clockwise so that the tongues latch onto the motor‟s sides. (Fig. 3 - left). 4) Reposition the anti-grease metallic – filter grilles.
If you can only find two wires in the cable (blue and brown), neither must be connected to the Earth terminal! As the colours of the wires in the appliance‟s mains lead may not correspond with the coloured markings identifying the terminals in your spur box, please proceed as follows: 1)The BLUE WIRE must be connected to the terminal marked “N” (Neutral), or coloured Black 2)The BROWN WIRE must be connected to the terminal marked “L” (LIVE), or coloured Red 3)The Green/Yellow wire must be connected to th
8. Put the extendable pipe on the outlet; after ensuring everything is ok, put down the hook and the external chimney, then the installation is complete, see pic 9.
Extraction / Air Purifier Modes of Operation Ensure that you have fitted the union (‘N’) (below and to the right) see to the upper part of the hood using the packaged two screws supplied inside the packing (Fig. 1 – on right). Using a 125 mm diameter pipe, connect the union (N) on the upper part of the hood (see Fig. 1) to the discharge outlet for cooking vapours with a crosssection of at least 150 cm².
. Fig.2 AIR PURIFIER OPERATION - INSTALLATION Instructions The cooker hood can be converted to work as an air purifier in the event that there is no provision for an external air discharge duct. In this case, air is recycled through the union „N‟ (Fig. 1 – above). When using the unit as an air purifier, you need to install two active carbon filters to absorb cooking vapours (please see page 10).
Troubleshooting If something has gone wrong with your Cooker Hood, checking against this chart might keep you from having to call for service. Symptom The cooker hood will not start! The cooker hood is not working effectively! The cooker hood has switched off during operation! Solution Check that the hood is connected to the electricity supply. Check that the fan speed control is set properly. The fan speed is not set high enough. The grease filter is dirty.
CONDITIONS OF GUARANTEE Dear Customer, The conditions of guarantee which apply to your appliance are as follows:This product is guaranteed for 3 years from the date of original purchase.Think Appliances will repair any defect that arises due to faulty manufacturing or workmanship free of charge during this period.
This guarantee does not cover: 1 2 3 4 5 Sinks and taps Failure to comply with the manufacturer’s instructions for use. The replacement of cosmetic components or accessories Accidental damage or wilful abuse. Subsequent loss or damage owing to the failure of the appliance or electrical supply.