BDWI460 45 cm Fully integrated full height electronic dishwasher
USER MANUAL FOR YOUR BAUMATIC BDWI460 45 cm Fully integrated full height electronic dishwasher NOTE: This User Instruction Manual contains important information, including safety & installation points, which will enable you to get the most out of your appliance. Please keep it in a safe place so that it is easily available for future reference; for you or any person not familiar with the operation of the appliance.
Contents Environmental note Important safety information 4 5–7 Specifications Product and aperture dimensions Product specifications Electrical details Description of the appliance Control panel 8 – 10 8 8–9 9 10 10 - 10 Using your dishwasher Before first use Filling with dishwasher salt Setting the water softener level Filling with rinse aid Setting the rinse aid level Filling with dishwasher detergent Loading the upper basket Adjusting the upper basket Loading the lower basket The cutlery basket Loadi
ENVIRONMENTAL NOTE Note: Before discarding an old appliance, switch off and disconnect it from the power supply. Cut off and render any plug useless. Cut the cable off directly behind the appliance to prevent misuse. This should be undertaken by a competent person. Disable the door lock to make sure that children cannot get stuck inside the appliance. o The packaging materials that Baumatic uses are environmentally friendly and can be recycled.
IMPORTANT SAFETY INFORMATION Your safety is of the utmost importance to Baumatic. Please make sure that you read this instruction booklet before attempting to install or use the appliance. If you are unsure of any of the information contained in this booklet, please contact the Baumatic Advice Line. General Safety o Repairs to your appliance must only be carried out by a Baumatic engineer or one of its authorised service agents.
o Care should be taken not to trap the power supply cable underneath the appliance whilst installing it. o No attempt should be made to alter or modify the specifications of this appliance. In daily use o This appliance is only designed to wash normal domestic wash loads. If you use your dishwasher in any other way or it is incorrectly used, then Baumatic accepts no liability for any damage that might be caused and any guarantee will be void.
Child Safety o Your dishwasher should only be used by adults. You should not allow children in the area of the machine unsupervised. You should not let them touch the controls or play with the appliance. o It could be possible for a child or pet to gain access to the dishwasher if the door is left open. Therefore please check the inside of the appliance before setting it on a wash cycle. o Any packaging that is removed from the machine should be kept away from children.
Specifications Product dimensions Height: Width: Depth: 815 - 865 mm 448 mm 550 mm Aperture dimensions Height: Width: Depth: 815 mm (min) 450 mm 580 mm (min) Product specifications o 10 Place settings o 6 functions: Normal Intensive Economy Glass Rapid 1 Hour o 6 temperatures: 40°C, 45°C, 50°C, 55°C, 60°C, 65°C 8
o o o o o o o o o o o o Delay timer LED display Self-cleaning stainless steel micro-filter Anti-leak device Anti-flood device Height adjustable upper basket Collapsible plate racks Pull out cutlery drawer Adjustable feet Residual drying Concealed heating element Half load o Low water consumption (9 litres) Energy efficiency details Energy efficiency class: A+ Washing performance class: A Drying performance class: A Power consumption Off mode: Left on mode: 0.45 W 0.
Description of the appliance 1) 2) 3) 4) 5) 6) Top spray arm Cutlery rack Upper basket Inner pipe Lower basket Salt dispenser / Water softener 7) 8) 9) 10) 11) 12) Control panel 1) 2) 3) 4) 5) 6) 7) 8) 9) 10 ON/OFF button Delay start button ON/OFF indicator neon Delay start indicator neons Rinse aid and salt indicator neons Half-load indicator Program indicator neons Half-load button Program selection button Detergent dispenser Cup shelf Bottom spray arm Main filter Inlet pipe connector Drain pipe c
Using your dishwasher Before first use o Install the appliance as per the installation instructions contained within this booklet. o Add 1.5Kg specialist dishwasher salt to the dishwasher water softener compartment and then fill with tap water. After this you should set the water softener level. o Fill the rinse aid dispenser and then set the rinse aid dosage. Filling with dishwasher salt IMPORTANT: You should only use salt that is specially designed for use in a dishwasher.
o It is perfectly normal for a small amount of water to come out of the water softener compartment. o Refit and fully tighten the water softener cap. o The salt required warning light will go out approximately 2-6 hours after you have filled the water softener with salt. When the salt indicator neon lights on the control panel in the future, you should follow the filling with dishwasher salt procedure again.
o IMPORTANT: If you are using 3 in 1 dishwasher tablets and live in a medium or hard water area, then you should still fill the water softener with salt. Filling with rinse aid The rinse aid is released during the final rinse and it helps to prevent water from forming droplets on your dishes. These droplets will lead to spots and streaks being left on items after the wash program has completed. o Your dishwasher is designed to utilise liquid rinse aid.
Setting the rinse aid level The amount of rinse aid that the dishwasher requires also depends on the hardness of your water. You should experiment with the rinse aid setting, until you find a level that gives the best results. o On the first wash cycle, we would recommend that the rinse aid level is set to number 4. o If you get water spots and poor drying performance, then you should turn the arrow anticlockwise and increase the setting to the next number.
o The left section displayed in the diagram (A) is for the main wash cycle detergent. Only one detergent tablet should be placed in the dispenser at any one time. If you are using detergent powder or liquid, you should follow the detergent manufacturer’s recommendations. o The right section displayed in the diagram (B) can have separate detergent placed in it for any wash cycle that has a pre-wash element to it, however this is optional.
Adjusting the upper basket Your dishwasher has an adjustable upper basket which you can alter to the most suitable position for the items you are going to wash in the upper basket. o The height of the upper basket can be adjusted by removing the upper basket from the guide runners. o NOTE: you must remove the end caps from the runners before removing the basket. o IMPORTANT: The upper basket must be empty when you are removing it from the guide runners.
Upper position o If the lower wheels are placed in the guide runners, then the basket is in the upper position. o For accommodating items such as glass tumblers and wine glasses. Wine glasses should be placed upside down, so that the stem of the glass rests in one of the grooves on the side flap. o Please note that when the basket is in the upper position, you cannot have the side flaps in a raised position. Otherwise the basket will not slide back into the interior of the dishwasher.
Loading the lower basket The lower basket is most suited to washing larger and more heavily soiled items, such as saucepans, saucepan lids and serving dishes. You can also load bowls and a variety of plates into the lower basket. 6. 7. 8. 9. 10. Dinner plates Dessert dishes Side plates Serving bowl Oval serving plate o Saucepans and serving bowls must always be placed with their bases upwards. o Deep saucepans should be slanted, to allow water to run off.
Loading dishes and cutlery Household cloths, sponges or any other object that may absorb water SHOULD NOT be washed in a dishwasher. o Remove leftovers and soften the remnants of burnt food in pans, prior to loading dishes in the appliance. o Once the dishwasher has been loaded, check that the spray arms can move freely. If the spray arm comes into contact with any item, then you should rearrange the wash load.
The following items are not always suitable for washing inside a dishwasher:o Stoneware should only be washed if the manufacturer of the item has marked it as dishwasher safe. o Plastic items (such as lunchboxes) should only be washed if the manufacturer has marked it as dishwasher safe. o Glazed crockery may fade with repeated washing inside of a dishwasher. o Items made of silverware or aluminium can discolour when washed inside a dishwasher.
Economy ** 1 Hour Glass Rapid For lightly soiled loads, such as plates, glasses, bowls and lightly soiled plates. For dishes that need to be rinsed and dried only. Pre-rinse Wash (50°C) Rinse (60°C) Drying Pre-rinse (50°C) Wash (60°C) Rinse (55°C) Drying For lightly Pre-rinse soiled loads, Wash such as (40°C) glasses, Rinse crystal and (60°C) fine china. Drying A shorter Wash wash for (40°C) lightly soiled Rinse loads that do Rinse not need (45°C) drying.
o IMPORTANT: Wait for 5 seconds before pressing the program selection button, otherwise the appliance may not function correctly. o Press the program selection button to choose an appropriate wash program for the load that you are washing. The relevant program indicator neon will light to show which program you have selected. o Select any program options that you want to use (e.g. delay start). o Close the door firmly, so that you hear the door lock click shut.
Adding an item to the wash NOTE: If you open the door during a wash cycle the machine will pause. When you close the door the machine will continue working after 10 seconds. o Slightly open the appliance door and wait for the spray arms to stop working. This will avoid scalding by hot water. o Fully open the door and add your required item to the basket. o Close the door. The appliance will resume the wash after 10 seconds.
Rinse aid and salt indicator neons o The rinse aid and salt indicator neons on the control panel will let you know when the appliance needs rinse aid or salt adding to it. neon indicates that you need to add rinse aid to the o The appliance. You should follow the procedure outlined on page 13. o The neon indicates that you need to add dishwasher salt to the appliance. You should follow the procedure outlined on page 11.
Cleaning and maintenance IMPORTANT: The appliance should be disconnected from your mains supply before commencing any cleaning process. The filter system Your appliance is fitted with three levels of filtering; these are located in the base of the dishwasher for ease of access. 1) Main filter 2) Coarse filter 3) Fine filter Main filter- Food and soil particles are trapped by this filter and pulverised by a special jet on the lower spray arm. This debris is then washed down the drain.
Cleaning the filters For best performance and results, the entire filter assembly should be thoroughly cleaned regularly (ideally after each wash cycle). 1. Turn the filter unit anticlockwise and then lift it upwards. 2. Separate the three filters 3. Rinse the filters separately under a tap to remove any food debris that is trapped in it. 4. Reassemble the three filters. 5. Place the filter unit back into its original positions in the base of the dishwasher.
Cleaning the spray arms The spray arms should be cleaned regularly, to prevent hard water deposits from clogging the spray arm jets and bearings. o To remove the spray arm, unscrew the nut and take out the washer that sits on top of the spray arm. o Gently pull to remove the spray arm. o Wash the spray arm in warm, soapy water and use a soft brush to clean the jets. o Rinse the spray arm thoroughly and then reassemble the spray arm back in its original position.
Error code failure system If your appliance senses that it is not operating correctly, then a neon light on the control panel will flash repeatedly. The following error indicators can possibly be remedied by the customer and the steps outlined below should be followed. BEFORE COMPLETING ANY MAINTAINEANCE ON THE APPLIANCE, IT SHOULD BE DISCONNECTED FROM YOUR MAINS POWER SUPPLY. The “Rapid” neon light flashes. o Longer than expected fill time. Check the water pressure of your mains water supply.
IF THE FAULT CODE REAPPEARS AFTER FOLLOWING THE ABOVE ADVICE AND CLEARING THE FAULT CODE. YOU SHOULD TURN OFF THE APPLIANCE; DISCONNECT THE APPLIANCE FROM YOUR MAINS SUPPLY. THEN ARRANGE FOR AN ENGINEER TO ATTEND THE APPLIANCE. YOU SHOULD CONTACT THE CUSTOMER CARE DEPARTMENT ON TELEPHONE NUMBER (0118) 933 6911. IF AN ENGINEER ATTENDS DURING THE GUARANTEE PERIOD AND FINDS THAT A FAULT HAS BEEN CAUSED BY AN ITEM ON THE ERROR CODE LIST, WHICH COULD HAVE BEEN CLEARED BY THE CUSTOMER.
Motor hums Suds in the tub Improper detergent use If the dishwasher is not going to be used for a period of time, then you should make sure that the appliance is set on a wash program once a week. Otherwise the seal around the motor may dry out and cause noise. Ensure if you are using 3 in 1 detergent tablets, in conjunction with rinse aid and salt that the levels are set correctly. Spilled rinse aid Always wipe up any excess rinse aid or rinse aid spillages immediately.
Installation IMPORTANT: THIS INSTALLATION MUST BE COMPLETED BY A SUITABLY QUALIFIED PERSON. BAUMATIC ONLY SANCTION THE INSTALLATION GIVEN IN THIS INSTRUCTION MANUAL. YOU SHOULD DISPOSE OF ALL PACKAGING IN AN ENVIRONMENTALLY FRIENDLY MANNER. Aperture requirements o The aperture that your dishwasher needs to be installed into should resemble the one shown in the drawing on page 39. o There should be less than a 5 mm gap between the top of the dishwasher and the underneath of the worktop.
Installation stages 1. 2. 3. 4. 5. 6. 7. 8. 9.
Preparing and connecting the furniture door o IMPORTANT: The furniture door is not supplied with the appliance. You should purchase one to match with the rest of your kitchen cabinets. o The maximum weight of the furniture door should be 5.5 kilograms. The maximum thickness of the furniture door should be 15 mm. o Use the installation template supplied with the appliance to mark up and then drill out the necessary holes in the furniture door. o Attach the upper hooks onto the furniture door.
o Lift the furniture door towards the dishwasher door, ensuring that the upper and lower hooks locate into the slots on the outside of the dishwasher door. o Push the furniture door downwards so it locks into place on the dishwasher door. o Open the dishwasher door and remove the short screws that are located on either side of the outer edge. o Insert the long screws into the holes. Make sure that you screw them tightly into the furniture door.
Adjusting the tension of the door spring o The door of the dishwasher is attached to springs. These are set at the factory to ensure that they are at the proper tension, so that the door can open and close smoothly. o After the furniture door has been fitted, you will need to adjust the tension of the door spring. o Using a screwdriver, rotate the adjusting screw to either tighten or slacken the steel cable.
Connecting to the mains water supply IMPORTANT: Do not connect the appliance to your mains water supply using an old or an existing water inlet hose. The inlet hose supplied with the dishwasher is the ONLY one that should be used. DO NOT CONNECT THE WATER INLET HOSE TO A HOT WATER TAP. o The inlet hose will be located inside the cabinet of the dishwasher. o Connect the water inlet hose to a threaded water tap that has a 3/4” thread and to the inlet hose connector on the appliance.
o IMPORTANT: Do not insert the drain hose too deeply into the pipe, as this may cause siphoning. o NEVER EXTEND THE DRAINAGE HOSE FROM ITS ORIGINAL LENGTH. Connecting to the power supply o IMPORTANT: The electrical socket must still be accessible once the appliance is installed. o Consult the rating plate, located on the right hand side of the drop down door BEFORE making the electrical connections. Ensure that the voltage reaching the plug is the same as that on the rating plate.
Applying the condensation strip o The condensation strip must be fitted to the underside of the worktop to protect it against the ingress of moisture. The strip will deflect steam that rises from your appliance, away from the underneath of the worktop. o The condensation strip will be located inside of your dishwasher. o Ensure that the underneath of the worktop is clean before sticking the strip to it. o Separate the backing paper away from the strip.
Positioning the dishwasher o Carefully slide the dishwasher back into position, underneath the worktop. Levelling the appliance o IMPORTANT: Your dishwasher must be level for it to operate properly. o Make sure that the dishwasher is supported whilst it is being levelled, otherwise it may tip over. o The rear feet can be adjusted by using the adjusting screw at the front of the appliance. o The front feet can be adjusted by hand or using a spanner. o Use a spirit level to check that the appliance is level.
Securing the dishwasher o The dishwasher must be secured to the worktop, this can be done in one of two ways:o Standard worktop- Secure the dishwasher to underside of the worktop by using two wood screws. the o You should screw through the holes in the brackets at the top of the dishwasher cabinet. o These screws should be fully tightened. o Marble/granite worktop- The material of the worktop will mean that it is impossible to put a screw through the underneath of the worktop.
My appliance isn’t working correctly IMPORTANT: If your appliance appears not to be operating correctly, then you should disconnect it from your mains supply and then contact the Customer Care Department on telephone number (0118) 933 6911. DO NOT ATTEMPT TO REPAIR THE APPLIANCE YOURSELF. Please note that if an engineer is asked to attend whilst the product is under guarantee and finds that the problem is not the result of an appliance fault, then you may be liable for the cost of the call out charge.
Baumatic Consumables o BC001 Degreaser for Dishwashers (200 g) o BC002 Descaler for Washing Machines and Dishwashers (200 g) o BC003 Ceramic Hob Cleaner (250 ml) o BC004 Oven Cleaner (250 ml) o BC005 Stainless Steel Cleaner and Protector (250 ml) o BC007 E-Cloth – General Purpose Cloth o BC008 Microwave Cover To order a Baumatic consumable product please call 0123 5437 244 and quote the product code. You can also order online from eshop.baumatic.co.
Technical Data Manufacturer Model Number Standard Place Settings Energy Efficiency Class (1) Annual Energy Consumption (2) Energy Consumption of the Standard Cleaning Cycle Power Consumption of Off Mode Power Consumption of Left-On Mode Annual Water Consumption (3) Drying Efficiency Class (4) Standard Cleaning Cycle (5) Program Duration of the Standard Cleaning Cycle Noise Level Installation Type BAUMATIC LTD BDWI460 10 A+ 238 kWh 0.83 kWh 0.45 W 0.
United Kingdom Baumatic Ltd., Baumatic Buildings, 6 Bennet Road, Reading, Berkshire RG2 0QX United Kingdom Sales Telephone (0118) 933 6900 Sales Fax (0118) 931 0035 Customer Care Telephone (0118) 933 6911 Customer Care Fax (0118) 986 9124 Spares Telephone (01235) 437244 Advice Line Telephone (0118) 933 6933 E-mail: sales@baumatic.co.uk customercare@baumatic.co.uk spares@baumatic.co.uk technical@baumatic.co.uk Website: www.baumatic.co.uk Facebook: www.facebook.com/baumatic.
