BEO910BGL 90 cm Glass Chimney Hood my
User Manual for your Baumatic BEO910BGL 90 cm Glass Chimney hood NOTE: This User Instruction Manual contains important information, including safety & installation points, which will enable you to get the most out of your appliance. Please keep it in a safe place so that it is easily available for future reference; for you or any person not familiar with the operation of the appliance.
Contents Page Environmental note 4 IMPORTANT SAFETY INFORMATION 5–7 Specifications of your cooker hood 8 Using your cooker hood Turning on the cooker hood Speed selection Light control The timer Turning off the cooker hood 9 – 11 9 – 10 10 10 11 11 Cleaning your Baumatic cooker hood Cleaning The grease filters 12 – 13 12 12 - 13 Maintenance Removing and cleaning the grease filters Changing a light bulb Fitting the carbon filters 13 13 14 16 - Installation Electrical connection Before beginning
ENVIRONMENTAL NOTE Note: Before discarding an old appliance, switch off and disconnect it from the power supply. Cut off and render any plug useless. Cut the cable off directly behind the appliance to prevent misuse. This should be undertaken by a competent person. CONFORMITY TO W.E.E.E.
IMPORTANT SAFETY INFORMATION Your safety is of the utmost importance to Baumatic. Please make sure that you read this instruction booklet before attempting to install or use the appliance. If you are unsure of any of the information contained in this booklet, please contact the Baumatic Customer Care Department. IMPORTANT: Any installation work must be carried out by a qualified electrician or competent person.
o The edges of the cooker hood are sharp – be mindful of this as you handle your appliance, especially during installation and cleaning. DO NOT CLEAN IN BEHIND THE GREASE FILTERS! o If the room where the cooker hood is to be used contains a fuel burning appliance such as a central heating boiler then its flue must be of the sealed or balanced flue type. o If other types of flue or appliances are fitted, ensure that there is an adequate supply of air in the room.
o Remember that when in extraction mode, your cooker hood is removing air from your room. Ensure that proper ventilation measures are being observed. o Note: Your cooker hood is designed to remove cooking odours from the room and not steam. o Warning - Always ensure that the cooker hood has been disconnected from the power supply before carrying out any work on the hood, including replacing light bulbs.
Specifications of your cooker hood PRODUCT DIMENSIONS Height: Width: Depth: 735 mm 900 mm 380 mm Your cooker hood is fitted with: o o o o o o o o Integrated centrifugal motor LCD display Touch control operation 4 Speeds Cut-off timer 2 x Washable aluminium grease filters 2 x LED lights Non-return air-flow flap o Extraction capacity: 1000 m³/hr o Optional extras: 1 x pair S1 Carbon filters required for recirculation CQ4SS Decorative Chimney Cover 8
Using your cooker hood o Make sure that it has been installed by a suitably qualified person, as per the information contained in Baumatic’s installation instructions. o There are several buttons on the control panel, which perform separate functions. Timer button Light control button Speed selection button Power button Slider control Turning on the cooker hood o After you have connected the cooker hood to the mains supply the backlight will turn on.
OR AT THE VERY LEAST WHEN YOU BEGIN COOKING. YOU SHOULD ALSO RUN YOUR HOOD FOR TEN MINUTES AFTER YOU HAVE FINISHED COOKING. Speed selection o Press the speed selection button to turn the speed selection function on and off. When you have turned the speed selection function on, you can then use the slider control to choose an operating speed for the motor. o The slider control has a total of 4 settings and 8 indicator lights so each speed has 2 correlating indicator lights.
The timer o You are able to program a countdown time for the cooker hood. After the set time has elapsed the hood will automatically switch off. o After you have selected your desired speed and light brightness, press the timer button to enter the timer setting mode. o You can then use the slider control to choose from 8 timer settings. There is an indicator light for each timer setting.
Cleaning your Baumatic cooker hood IMPORTANT: BEFORE CLEANING, ALWAYS ENSURE THAT YOU HAVE SWITCHED YOUR COOKER HOOD OFF AT THE OMNI-POLAR SWITCH, SET AT THE WALL FROM THE CABLE. Cleaning o Clean the external parts of your cooker hood with mild liquid detergent and a new damp cloth. o Never use abrasive powder, corrosive solvents or brushes. o Never insert pointed objects into the motor’s protective grid.
o DO NOT WASH THE GREASE FILTERS IN A DISHWASHER. Maintenance Removing and cleaning the grease filters o Press and hold the power button for 3 seconds to open the decorative cover and allow access to the grease filters. o Remove the grease filters by pulling down on the handle and pulling them away from the cooker hood. o Soak the grease filters in hot water and washing up liquid for at least 3 minutes. Then use a soft brush to loosen any grease deposits that have formed.
o Repeat the process if required. o Refit the grease filters once they have dried and press and hold the power button for 3 seconds to close the decorative lid. o IMPORTANT: Let the grease filters dry thoroughly before refitting them in the cooker hood. Changing a light bulb IMPORTANT: BEFORE ATTEMPTING TO CHANGE A LIGHT BULB, YOU MUST ENSURE THAT YOU HAVE DISCONNECTED THE COOKER HOOD FROM YOUR MAINS SUPPLY. o Prior to touching the light bulbs ensure they are cooled down.
o Fit the replacement bulb in the same manner as the original and reconnect the light wiring point. o IMPORTANT: Defective bulbs should be replaced immediately. o If the light or lights still do not work, make sure that the lamps are fitted properly into their housings before you call for technical assistance. o Refit the grease filters and reconnect the cooker hood to your mains supply in order to close the decorative cover.
Fitting the carbon filters If the appliance is to be used in recirculation mode then it is necessary to fit carbon filters. This will help to absorb unpleasant odours caused by cooking. IMPORTANT: BEFORE ATTEMPTING TO FIT OR REMOVE THE CARBON FILTERS, YOU MUST ENSURE THAT YOU HAVE DISCONNECTED THE COOKER HOOD FROM YOUR MAINS SUPPLY. 1) First open the decorative cover and remove the grease filters (as previously described).
o The carbon filters should be replaced every 3 - 6 months or if they show signs of damage. Installation IMPORTANT: Before installation and usage read all the instructions and make sure that the voltage (V) and the frequency (Hz) indicated on the rating plate are exactly the same as the voltage and frequency in your home. The rating plate can be found behind the grease filters.
If you only find two wires in the main’s lead (blue and brown), then neither must be connected to the earth terminal. o As the colours of the wires in the appliance’s mains lead may not correspond with the coloured markings identifying the terminals in your spur box, please proceed as follows: o The blue wire must be connected to the terminal marked “N” (neutral), or coloured black. o The brown wire must be connected to the terminal marked “L” (live), or coloured red.
o In addition check whether there is an electrical socket available, which will be accessible after the hood is mounted. If you are going to use the appliance in extractor mode, you should also ensure that there is space to connect a fumes discharge device to the outside. o Rawl plugs are provided to secure the hood to most types of walls and ceilings. However a qualified technician must verify the suitability of the materials, in accordance with the type of wall and ceiling.
Installing your cooker hood o We recommend that at least two people install this hood. o Please note that the styles of cooker hood shown in the line drawings on the following pages are sometimes different to the shape of the BEO910BGL. However the installation method shown is correct and MUST be followed. IMPORTANT: YOUR COOKER HOOD SHOULD BE CONNECTED TO YOUR MAINS SUPPLY AFTER THE REST OF THE INSTALLATION PROCESS HAS BEEN COMPLETED.
5) Connect the cooker hood to the mains supply and turn the cooker hood on by pressing the power button for 3 seconds. This will open the decorative cover. Disconnect the cooker hood from the mains supply. The decorative cover will stay open. Remove the grease filters. 6) Screw ST4*30 screws into the holes at the back of the cooker hood as shown in the drawing below.
o The other end of the ducting hose should be connected to a discharge outlet that is suitable for cooking vapours. It should have a cross section of at least 150 cm². o The maximum distance between the coupling and your discharge outlet should be 3 metres, with one 90 degree bend. For each additional 90 degree bend, the maximum distance is reduced by a further metre. Fitting the optional chimney sections (CQ4SS) 9) Take the two chimney sections (C) and (D).
o Mark the side measurements of both sides of chimney section (D) on the wall with a pencil and then remove chimney section (D). 11) Take the flat bracket (E) and place it between the two pencil marks that you made in step 9 o Keeping the bracket in contact with the wall, use a pencil to mark on the wall the anchoring holes that are cut out of the bracket. 12) Using an 8 mm drill bit, drill out two holes on the pencil markings that you made in step 11.
o Refit chimney section (C) to the hood and fix it onto the hood using the two screws that are supplied. o Secure the top of chimney section (C) to the flat bracket, using the screws provided. o Slide chimney section (D) inside of chimney section (C). Then secure the L shaped bracket to the wall, using the same method as you have just used to secure the lower bracket. 13) Lift chimney section (D) up to the ceiling and secure it to the L shaped bracket using the screws provided.
Troubleshooting IMPORTANT: If your cooker hood appears not to be operating properly, before contacting the Baumatic Customer Care Department, please refer to the checklist below. My cooker hood will not start. o Check that the hood is connected to the electricity supply o Check that the fan speed control is set correctly. My cooker hood is not working effectively. o The fan speed is not set high enough o The grease filters are dirty and require cleaning. o The kitchen is not well ventilated enough.
IMPORTANT: If your appliance appears not to be operating correctly, then you should disconnect it from your mains supply and then contact Baumatic Customer Care on telephone number (0118) 933 6911. DO NOT ATTEMPT TO REPAIR THE APPLIANCE YOURSELF. Please note that if an engineer is asked to attend whilst the product is under guarantee and finds that the problem is not the result of an appliance fault, then you may be liable for the cost of the call out charge.
Baumatic consumables o BC001 Degreaser for Dishwashers (200 g) o BC002 Descaler for Washing Machines and Dishwashers (200 g) o BC003 Ceramic Hob Cleaner (250 ml) o BC004 Oven Cleaner (250 ml) o BC005 Stainless Steel Cleaner and Protector (250 ml) o BC007 E-Cloth – General Purpose Cloth o BC008 Microwave Cover To order a Baumatic consumable product please call 0123 5437 244 and quote the product code. You can also order online from eshop.baumatic.co.
United Kingdom Baumatic Ltd., Baumatic Buildings, 6 Bennet Road, Reading, Berkshire RG2 0QX United Kingdom Sales Telephone (0118) 933 6900 Sales Fax (0118) 931 0035 Customer Care Telephone (0118) 933 6911 Customer Care Fax (0118) 986 9124 Spares Telephone (01235) 437244 Advice Line Telephone (0118) 933 6933 E-mail: sales@baumatic.co.uk customercare@baumatic.co.uk spares@baumatic.co.uk technical@baumatic.co.uk Website: www.baumatic.co.uk Czech Republic Baumatic CR spol s.r.o.
