Instructions for the installation and advice for the maintenance MODEL: BGH60 Instructions Manual MODEL: BGH60 PLEASE READ THIS MANUAL BEFORE INSTALLING THE HOTPLATE. COD:01099HS - 31.07.
Dear Customer, Congratulations on purchasing your new product from Think Appliances. To register your parts and labour warranty (some conditions apply please refer to your warranty card for more details) please contact out Customer Care team on: 1800 444 357 Our Customer Care centre is there to ensure you get the most out of your appliance.
DESCRIPTION OF THE HOT PLATES MODEL: BGH60 1 Rapid gas burner 2 Semi-rapid gas burner 3 Auxiliary gas burner 7 Trivet 2 burner 8 Burner 3 control knob 9 Burner 1 control knob 10 Burner 2 control knob (right) 11 Burner 2 control knob (left) 15 Electric ignition button 16 Ultra rapid gas burner/Wok 17 Trivet for ultra rapid burner 18 Burner 16 control knob Natural 12.0 MJ 7.1 MJ 4.1 MJ U-LPG 10.4 MJ 6.2 MJ 3.5 MJ 14.5 MJ 11.
USE 1) BURNERS the reduced rate position (small flame fig. 1). - Always place a lid on the pans. A diagram is screen-printed above each knob on the front panel. This diagram indicates to which burner the knob in question corresponds. After having opened the gas mains or gas bottle tap, light the burners as described below: - Manual ignition Push and turn the knob corresponding to the required burner in an anticlockwise direction until it reaches the full on position (large flame fig.
USE Notes: Use of a gas cooking appliance produces heat and moisture in the room in which it is installed. The room must therefore be well ventilated by keeping the natural air vents clear (fig. 3) and by activating the mechanical aeration device (suction hood or electric fan fig. 4 and fig. 5). Intensive and lengthy use of the appliance may require additional ventilation. This can be achieved by opening a window or by increasing the power of the mechanical exhausting system if installed.
CLEANING CARE & MAINTENANCE To optimize the appearance and up keep of stainless steel: 1) ALWAYS keep stainless steel out of contact from acid/acid based solvent (liquid or vapour form). 2) After installation, wipe clean all stainless steel products with a soft damp cloth to remove any traces of dirt (e.g. cement dust) or condensation marks. In the event where persistent marks appear: immediately clean affected areas with stainless steel cleaner, using a clean damp soft cloth.
INSTALLATION TECHNICAL INFORMATION FOR THE INSTALLER Any adjoining wall surface situated within 200 mm from the edge of any hob burner must be a suitable non-combustible material for a height of 150 mm for the entire length of the hob. Any combustible construction above the hotplate must be at least 600 mm above the construction above the top of the burner and no construction shall be within 450 mm above the top of the burner.
5) GAS CONNECTION INSTALLATION Liquified Petroleum Gas In a LPG installation the gas regulation is made at the gas cylinder and regulation at the appliance is not required. To connect supply to the appliance use transition pieces as shown in figure 12. These pieces are supplied with the appliance on purchase. The gas connection is located in the rear and on the underside of the appliance 100 mm from the right hand side. A. The hotplate can be connected with rigid pipe as specified in AS5601 table 3.1. B.
INSTALLATION 6) ELECTRICAL CONNECTION - The power supply cable must be positioned so that no part of it is able to reach an overtemperature of 75 K. - Never use reductions, adapters of shunts for connection since these could create false contacts and lead to dangerous overheating. When the appliance is connected straight to the electricity main: - Install an omnipolar circuit-breaker between the appliance and the electricity main.
ADJUSTMENTS 7) TAPS Always disconnect the appliance from the electricity main before making any adjustments. All seals must be replaced by the technician at the end of any adjustments or regulations. Our burners do not require primary air adjustment. a) Data Label The Data Label is located on the underside of the hotplate. A duplicate Data Label is supplied to adhere in an accessible area next to the hotplate.
CONVERSIONS 8) U-LPG TO NATURAL GAS CONVERSION PROCEDURE 9) NATURAL GAS TO UNIVERSAL LPG CONVERSION PROCEDURE Appliance models: Gas stainless steel hotplate models: BGH60 Appliance models: Gas stainless steel hotplate models: BGH60 1. Remove each burner cap and burner skirt. 2. Remove the U-LPG main injector with a 7 mm/VF tube spanner and replace with the appropriate size Natural Gas injector for each burner. The following injector sizes are required for Natural Gas: 1.
CONVERSIONS 10) REPLACING THE INJECTORS affix the label corresponding to the new gas regulation on the appliance instead of the already existing one. This label is supplied in the packet containing the spare injectors. The envelope with the injectors and the labels can be included in the kit, or at disposal to the authorised customer Service Centre.
SERVICING Always turn off the electrical ignition before proceeding with any servicing operation. Servicing should be carried out only by authorised personnel. Greasing the taps (see fig. 17 - 18) If a tap becomes stiff to operate, it must be immediately greased in compliance with the following instructions: - Remove the tap. - Clean the cone and its housing using a cloth soaked in solvent. - Lightly spread the cone with the relevant grease.
SERVICING CABLE TYPES AND SECTIONS TYPE OF HOT PLATE Gas hot plate TYPE OF CABLE H05 RR - F SINGLE - PHASE POWER SUPPLY Section 3 X 0.75 mm2 ATTENTION!!! If the power supply cable is replaced, the installer should leave the ground wire longer than the phase conductors (fig. 19) and comply with the recommendations given in paragraph 6. FIG.
TECHNICAL ASSISTANCE AND SPARE PARTS Before leaving the factory, this appliance will have been tested and regulated by expert and specialized personnel in order to guarantee the best performances. Any repairs or adjustments which may be subsequently required may only be carried out by qualified personnel with the utmost care and attention.
! " # $ $ # % & ' (% ' ) * + %! , ' %! % & ' ' &' - .
