BHC606BE/BHC606SS 60cm touch control ceramic hob 1
User Manual for your Baumatic BHC606BE/BHC606SS 60 cm Front touch control 4 zone ceramic hob NOTE: This User Instruction Manual contains important information, including safety & installation points, which will enable you to get the most out of your appliance. Please keep it in a safe place so that it is easily available for future reference; for you or any person not familiar with the operation of the appliance.
Contents Environmental note 4 Important safety information 5–8 Specifications Ceramic hob layout Control panel layout 8 – 10 9 10 Using the ceramic hob Before first use Touch controls Switching the hob top on Switching on a zone and setting a power level Switching off a zone Switching off the hob Residual heat indicator Switching on the dual cooking zone Locking the hob top The hob timer Setting a countdown time Safety cut-off 10 - 16 10 10 11 11 11 12 12 12 - 13 14 14 – 15 15 16 Hob guidelines 16
Environmental note o The packaging materials that Baumatic uses are environmentally friendly and can be recycled. o Please discard all packaging material with due regard for the environment.
Important safety information Your safety is of the utmost importance to Baumatic. Please make sure that you read this instruction booklet before attempting to install or use the appliance. If you are unsure of any of the information contained in this booklet, please contact the Baumatic Advice Line. General Information o This appliance is designed for domestic household use and for the cooking and frying of domestic foodstuffs.
Child Safety o Baumatic strongly recommend that babies and young children are prevented from being near to the appliance and not allowed to touch the appliance at any time. During and after use, all surfaces will become hot. o If it is necessary for younger family members to be in the kitchen, please ensure that they are kept under close supervision at all times. o Older children should only be allowed to utilise the appliance when supervised.
Cleaning o Cleaning of the hob should be carried out on a regular basis. o IMPORTANT: Before attempting to clean the appliance, it should be disconnected from the mains and allowed to cool. o Great care should be taken whilst using this appliance and when following the cleaning procedure. o You should not use a steam jet or any other high pressure cleaning equipment to clean the appliance.
o Pans should be lifted on and off the hob surface and not dragged. o Cooking zones should not be switched on without cookware placed on it. Also the cookware should not be empty. Specifications Product dimensions: Aperture dimensions: Depth: Width: Height: Depth: Width: 520 mm 590 mm 52 mm 490 mm (+5) mm 560 mm (+5) mm Product specifications: o o o o o o o o o 1 x 1.80 kW hyperspeed zone (Ø 180 mm) 2 x 1.20 kW hyperspeed zones (Ø 145 mm) 1 x 1.00/1.
Electrical details Rated Voltage: Supply Connection: Max Rated Inputs: Mains Supply Lead: 230 Vac 50 Hz 30 A (double pole switched fused outlet with 3mm contact gap) 6.4 kW 3 core x 4 mm² (not supplied) For future reference please record the following information which can be found on the rating plate and the date of purchase which can be found on your sales invoice. The rating plate of your hob is located on the underneath of the appliance.
Control panel layout 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Safety lock button Cooking zone minus button Cooking zone indicator Cooking zone plus button Timer minus button Timer display Timer button Timer plus button Dual cooking zone ON/OFF button ON/OFF button Using the ceramic hob Before first use IMPORTANT: You should clean the ceramic hob surface (see “Cleaning and maintenance” section). o You should switch on one cooking zone at a time, for 5 minutes at the maximum setting.
Switching the hob top on o Press the ON/OFF button (10) to switch on the appliance. o The hob will beep once and all of the cooking zone indicators will light briefly then go out. o This means that the hob has entered stand-by mode. Switching on a zone and setting a power level IMPORTANT: A zone must be selected within 2 minutes of switching the hob on. o Press the cooking zone plus button (4) of the zone that you want to use.
Switching off the hob o Once you have switched off all of the cooking zones, you should turn off the hob. o Press the ON/OFF button (10). o It is possible to turn the hob off at any time by pressing the ON/OFF button (10). o The hob will switch off automatically after 2 minutes, if none of the zones are in use. Residual heat indicator o After a zone is switched off, the corresponding cooking zone indicator (3) will show a flashing letter “H”.
o Press the cooking zone plus button (4) for the dual circuit zone. o Adjust the zone between power levels 1 and 9, using the plus (4) and minus (2) buttons. By holding down either of these buttons, the value on the zone indicator (3) will adjust up or down. o The central section of the dual cooking zone will switch on. o If you wish to activate the outer section as well, you should press the dual cooking zone ON/OFF button (9). A neon above the button will light.
Locking the hob top o The whole hob top can be locked by pressing the safety lock button (1) whilst the appliance is switched on. o The timer display (6) will show “L0” to indicate that the safety lock feature has been activated. o When the safety lock has been switched on, it will disable any of the other buttons on the control panel, apart from the ON/OFF button (8). o To disable the safety lock feature, you should press the safety lock button (1) again.
o The timer display will decrease in 1 minute intervals each time the timer minus button (5) is pressed. o If the set time exceeds 99 minutes, the timer display will return to showing 0. o If you press the timer plus (8) and minus buttons (5) simultaneously, the timer display will reset to 0. Setting a countdown time o Press the ON/OFF button (9) to switch on the appliance. o Press the cooking zone plus button (4) of the zone that you want to use.
Safety cut-off o If one or more of the cooking zones are accidentally left on, a safety cut off will activate after a certain period of time. The length of time depends on the power level that a zone or zones have been set on. LEVEL TIME LIMIT (hours) 1 8 2 8 3 8 4 4 5 4 6 4 7 2 8 2 9 2 o If more than one zone is operating when one of the zones reaches its safety cut-off point, only the zone which has reached its safety cut off point will switch off.
o The best thickness for the bottom of the pans is 2 – 3 mm of enamelled steel and 4 – 6 mm for stainless steel with sandwich type bottoms. o If these rules are not followed, then there will be a great loss of heat and energy. Heat not absorbed by the saucepan, will spread to the hob, frame and surrounding cabinets. o Preferably cover pans with a lid to permit cooking at a lower heat. o Always cook vegetables and potatoes, etc. in as little water to reduce cooking times.
Cleaning and maintenance Cleaning operations must only be carried out when the hob is cool. The appliance should be disconnected from your mains supply before commencing any cleaning process. Cleaning the ceramic hob top Any residues that are left on the hob top surface from cleaning agents will damage it. You should remove any residues with warm water mixed with a little washing up liquid.
Using a ceramic hob scraper Your appliance will be provided with a hob scraper. The following guidelines should also be followed when using the ceramic hob scraper:- o The scraper should be placed on the ceramic surface at an angle. o Residues should be removed by sliding the blade carefully over the ceramic surface. o The ceramic surface should be wiped with a damp cloth that has been placed in warm water mixed with a small amount of washing up liquid.
Positioning The adjacent furniture must be able to withstand a minimum temperature rise of 85°C above the ambient temperature of the room it is located in, during periods of use. This appliance is classified as Class 3 and therefore is to be built into a kitchen unit (depending on size) or 600 mm worktop that is at least 30 mm thick. The following minimum clearance distances must be observed:o 700 mm between the hob surface and the underside of any horizontal surface above it.
Installing the appliance o Cut a hole in the worktop that corresponds with the drawing shown above. o IMPORTANT: You must observe the ventilation requirements shown in the drawing opposite. o IMPORTANT: There are ventilation holes around the outside of the hob. YOU MUST ensure that these holes are not blocked by the work top, when you put the hob into position (see drawing opposite). o Carefully turn the hob upside down and place it on a cushioned mat.
o IMPORTANT: Do not use a silicon sealant to seal the appliance against the aperture. This will make it difficult to remove the hob from the aperture in future, particularly if it needs to be serviced. o Carefully turn the hob back over and then gently lower it into the aperture hole that you have cut out. o There are holes on the base or the sides of the hob that you can fix the four brackets to. There are three holes in each one of the brackets.
Electrical connection This appliance must be installed by a qualified person in accordance with the latest edition of the I.E.E. Regulations and in compliance with Baumatic’s instructions. Before connecting the appliance, make sure that the supply voltage marked on the rating plate corresponds with your mains supply voltage. WARNING: THIS APPLIANCE MUST BE EARTHED.
o The cable connections must be in accordance with the diagram located on the bottom of the hob (see above). o You should use a good quality screwdriver to carefully, fully tighten ALL of the terminal screws. o If when the hob is first switched on, only two of the zones work, you should recheck that the terminal screws are all fully tightened. This should be done before contacting the Customer Care Department.
o Switch the appliance off at the socket. o Open the terminal block on the underside of the hob. o Unscrew the terminal screws fixing the cable. o Replace the cable with one of the same length and in accordance with the specification given on page 23. o The “green-yellow” earth wire must be connected to the terminal marked . It must be about 10 mm longer than the live and neutral wires.
o A humming sound is heard when a cooking zone is selected. * This is normal; the sound will disappear when the zone heats up. o The cooking zones have become discoloured. * This maybe caused by burnt on remnants of food. This will not affect the working of the appliance. However you should make sure that the cleaning instructions are being followed regularly.
United Kingdom Baumatic Ltd., Baumatic Buildings, 6 Bennet Road, Reading, Berkshire RG2 0QX United Kingdom Czech Republic Baumatic CR spol s.r.o. Průmyslová zóna Sever 696 460 11 Liberec 11 Czech Republic Sales Telephone (0118) 933 6900 Sales Fax (0118) 931 0035 Customer Care Telephone (0118) 933 6911 Customer Care Fax (0118) 986 9124 Spares Telephone (01235) 437244 Advice Line Telephone (0118) 933 6933 www.baumatic.cz E-mail: sales@baumatic.co.uk customercare@baumatic.co.uk spares@baumatic.co.
27
