BHG300.5SS BHG610.5SS BHG900.5SS BHG604.5SS/W BHG710.
User Manual for your Baumatic BHG300.5SS BHG604.5SS/W BHG610.5SS BHG710.5SS BHG900.5SS GAS HOB NOTE: This User Instruction Manual contains important information, including safety & installation points, which will enable you to get the most out of your appliance. Please keep it in a safe place so that it is easily available for future reference; for you or any person not familiar with the operation of the appliance.
Contents Environmental note 4 Important safety information 5-7 Specifications Product details/specifications/dimensions: o BHG300.5SS o BHG604.5SS/W o BHG610.5SS o BHG710.5SS o BHG900.
Environmental note o The packaging materials that Baumatic uses are environmentally friendly and can be recycled. o Please discard all packaging material with due regard for the environment.
Important safety information Your safety is of the utmost importance to Baumatic. Please make sure that you read this instruction booklet before attempting to install or use the appliance. If you are unsure of any of the information contained in this booklet, please contact the Baumatic Customer Care Department. General Information o This appliance is designed for domestic household use and for the cooking and frying of domestic foodstuffs.
Child Safety o Baumatic strongly recommend that babies and young children are prevented from being near to the appliance and not allowed to touch the appliance at any time. During and after use, all surfaces will be hot. o If it is necessary for younger family members to be in the kitchen, please ensure that they are kept under close supervision at all times. o Older children should only be allowed to utilise the appliance when supervised.
o Great care should be taken whilst using this appliance and when following the cleaning procedure. o You should not use a steam jet or any other high pressure cleaning equipment to clean the appliance. Installation This appliance must be correctly installed by a GASSAFE registered installer, strictly in accordance with the manufacturer’s instructions and the relevant British Standards. Please see the specific section of this booklet that refers to installation.
Specifications – BHG300.5SS Product dimensions: Depth: Width: Height: 510 mm 288 mm 45 mm Aperture dimensions: Depth: Width: 494 mm 270 mm Product specifications: o o o o o o 1 x 3.00 kW rapid burner 1 x 1.00 kW auxiliary burner Front control operation Enamelled pan stands Automatic ignition Flame failure safety device on each burner Standard accessories: o LPG conversion jets Gas hob surface layout 1 = 1.00 kW auxiliary burner 2 = 3.
Specifications – BHG604.5SS/W Product dimensions: Aperture dimensions: Depth: Width: Height: Depth: Width: 510 mm 620 mm 50 mm 480 mm 560 mm Product specifications: o o o o o o o 1 x 3.00 kW rapid burner 2 x 1.75 kW semi-rapid burners 1 x 1.00 kW auxiliary burner Front control operation Enamelled pan stands Automatic ignition Flame failure safety device on each burner Standard accessories: o LPG conversion jets Gas hob surface layout 1 2 3 4 = = = = 1.75 1.75 3.00 1.
Specifications – BHG610.5SS Product dimensions: Aperture dimensions: Depth: Width: Height: Depth: Width: 510 mm 620 mm 50 mm 480 mm 560 mm Product specifications: o o o o o o o o 1 x 3.50 kW triple crown (wok) burner 1 x 1.75 kW semi-rapid burners 1 x 3.00 kW rapid burner 1 x 1.
Specifications – BHG710.5SS Product dimensions: Aperture dimensions: Depth: Width: Height: Depth: Width: 510 mm 720 mm 50 mm 480 mm 560 mm Product specifications: o o o o o o o o 1 x 3.00 kW rapid burner 2 x 1.75 kW semi-rapid burners 1 x 1.00 kW auxiliary burner 1 x 3.
Specifications – BHG900.5SS Product dimensions: Aperture dimensions: Depth: Width: Height: Depth: Width: 510 mm 909 mm 50 mm 480 mm 840 mm Product specifications: o o o o o o o o 1 x 3.00 kW rapid burner 2 x 1.75 kW semi-rapid burners 1 x 1.00 kW auxiliary burner 1 x 3.
Electrical details Rated Voltage: Supply Connection: Mains Supply Lead: 230 Vac 50 Hz 3A (double pole switched fused outlet with 3mm contact gap) 3 core x 1.5 mm² Gas details Connection: Type: Rp ½ (ISO R7) Natural Gas (20 mbar) Alternative LPG G30 (28-30/37 mbar) For future reference please record the following information which can be found on the rating plate and the date of purchase which can be found on your sales invoice. The rating plate of your hob is located on the underneath of the appliance.
Using the gas hob Before first use IMPORTANT: You should clean the hob surface (see “Cleaning and maintenance” section). The gas hob The following symbols will appear on the control panel, next to each control knob: Circle: gas off Large flame: maximum setting / ignition position Small flame: minimum setting o The minimum setting is at the end of the anti-clockwise rotation of the control knob. o All operation positions must be selected between the maximum and minimum position.
Automatic ignition with flame failure safety device The appliance is fitted with a flame failure safety device on each burner, which is designed to stop the flow of gas to the burner head in the event of the flame going out. To ignite a burner: o Press in the control knob of the burner that you wish to light and turn it anti-clockwise to the maximum position. o If you keep the control knob depressed, the automatic ignition for the burner will operate.
Energy saving tips Burners Pan Ø min Wok 200 mm Rapid 200 mm Semi-rapid 140 mm Auxiliary 100 mm size Ø max 320 mm 260 mm 200 mm 140 mm o The diameter of the bottom of the pan should correspond to that of the burner. o The burner flame must never extend beyond the diameter of the pan. o Use flat bottomed pans only. o When possible, keep a lid on the pan whilst cooking. o Cook vegetables with as little water as possible, to reduce cooking times.
Cleaning Cleaning operations must only be carried out when the hob is cool. The appliance should be disconnected from your mains supply before commencing any cleaning process. Cleaning the hob top Any residues that are left on the hob top surface from cleaning agents will damage it. You should remove any residues with warm soapy water. Abrasive cleaners or sharp objects will damage the hob surface; you should clean it using warm soapy water.
o Soak them for about ten minutes in hot water and a little detergent. o After cleaning and washing them, wipe and dry them carefully. o Before placing the burners back on the hob top, make sure that the gas jet is not blocked. o IMPORTANT: Make sure that you reassemble the burners in the original way. Maintaining the enamelled pan stands (BHG300.5SS / BHG604.5SS/W) o IMPORTANT: Make sure that the hob surface and pan stands have cooled before you attempt to touch them.
Installation The installation must be carried out by a GASSAFE registered installer, in accordance with the current version of the following.
Positioning The adjacent furniture must be able to withstand a minimum temperature rise of 85°C above the ambient temperature of the room it is located in, during periods of use. * * * * 300 600 700 900 mm mm mm mm (BHG300.5SS) (BHG604.5SS, BHG610.5SS) (BHG710.5SS) (BHG900.5SS) o This appliance can be located in a kitchen, a kitchen diner or a sitting room. IMPORTANT: The appliance must not be installed in a bathroom or shower room.
o If the hob is positioned so that the right or left hand side of the appliance will be near to the edge of a kitchen unit. There must be a gap of at least 150 mm between the side of the hob and the vertical surface of any kitchen unit that is made of a combustible material. If the vertical surface is made of a non-combustible material, then 55 mm clearance is sufficient. HOWEVER sufficient space must be allowed for saucepan handles to be turned and for saucepans to be used safely.
Installing the appliance o Cut a hole in the worktop that corresponds with the correct model drawing: BHG300.5SS BHG710.5SS BHG604.5SS/W & BHG610.5SS BHG900.5SS o Carefully turn the hob upside down and place it on a cushioned mat. o Remove the protective covering from the sealing strip o Apply the sealing strip provided around the edge of the appliance. o Do not leave a gap in the sealing strip or overlap the thickness.
IMPORTANT: Do not use a silicon sealant to seal the appliance against the aperture. This will make it difficult to remove the hob from the aperture in future, particularly if it needs to be serviced. o Carefully turn the hob back over and then gently lower it into the aperture hole that you have cut out. o On the underneath of the hob, place the clamp(s) (B) into position on in each corner of the hob.
o Conversion for use on LPG and other gases must only be undertaken by a qualified person. For information on the use of other gases, please contact the Baumatic Customer Care Department. o The hob must be installed by a qualified person, in accordance with the current edition of the Gas Safety (Installation and Use) (Amendment) Regulations and the relevant building/I.E.E. Regulations.
o This hob is not fitted with a device for discharging the products of combustion. Ensure that the ventilation rules and regulations are followed. o The walls behind and near the hob should be resistant to heat, steam and condensation. o Remember that the quantity of air necessary for combustion must never be less than 2m³/h for each kW of power (see total power in kW on the appliance rating plate).
Gas adjustment (Conversion to LPG) All work must be registered engineer. carried out by a GASSAFE IMPORTANT: Always isolate the hob from the electricity supply before changing the injectors and/or adjusting the minimum flow of the burners. o Remove the pan-stands, flame spreaders (A). burners and o Unscrew the injector (B) and replace it with the stipulated injector for the new gas supply (see the table on the next page).
Minimum flow adjustment for hob gas taps. All work must be registered engineer. carried out by a GASSAFE IMPORTANT: Always isolate the hob from the electricity supply before changing the injectors and/or adjusting the minimum flow of the burners. o Switch the burner on and set the knob at the minimum position. o Remove the knob from the tap and place a small bladed screwdriver in the centre of the tap shaft.
Gas tap maintenance These maintenance operations MUST ONLY be carried out by a GASSAFE registered engineer. IMPORTANT: Before carrying out any maintenance operations, disconnect the appliance from the gas and electricity supplies. If a gas tap becomes stiff to operate, then you should proceed as follows: o Remove the control knobs, pan supports, burners, hob fixing screws and clamps. o Remove the hob from the worktop and remove any underside protective covers.
Electrical connection This appliance must be installed by a qualified person in accordance with the latest edition of the I.E.E. Regulations and in compliance with the manufacturer’s instructions. Before connecting the appliance, make sure that the supply voltage marked on the rating plate corresponds with your mains supply voltage. o Cable type: H05 RRF 3 core x 1.5 mm³ (Type RR-F marked). o The mains supply cable is supplied with this product.
My appliance isn’t working correctly IMPORTANT: If your appliance appears not to be operating correctly, then you should disconnect it from your mains supply and then contact the Baumatic Customer Care Department on telephone number (0118) 933 6911. DO NOT ATTEMPT TO REPAIR THE APPLIANCE YOURSELF.
Baumatic Consumables o BC001 Degreaser for Dishwashers (200 g) o BC002 Descaler for Washing Machines and Dishwashers (200 g) o BC003 Ceramic Hob Cleaner (250 ml) o BC004 Oven Cleaner (250 ml) o BC005 Stainless Steel Cleaner and Protector (250 ml) o BC007 E-Cloth – General Purpose Cloth o BC008 Microwave Cover To order a Baumatic consumable product please call 0123 5437 244 and quote the product code. You can also order online from eshop.baumatic.co.
Czech Republic Baumatic CR spol s.r.o. Lípovà 665 460 01 Liberec 4 Czech Republic United Kingdom Baumatic Ltd., Baumatic Buildings, 6 Bennet Road, Reading, Berkshire RG2 0QX United Kingdom +420 483 577 200 www.baumatic.cz Slovakia Baumatic Slovakia, s.r.o.
