BHG300.5SS BHG610.5SS BHG900.5SS BHG604.5SS/W BHG710.
User Manual for your Baumatic BHG300.5SS BHG604.5SS/W BHG610.5SS BHG710.5SS BHG900.5SS GAS HOB NOTE: This User Instruction Manual contains important information, including safety & installation points, which will enable you to get the most out of your appliance. Please keep it in a safe place so that it is easily available for future reference; for you or any person not familiar with the operation of the appliance.
Contents Environmental note 4 Important safety information 5-7 Specifications Product details/specifications/dimensions: o BHG300.5SS o BHG604.5SS/W o BHG610.5SS o BHG710.5SS o BHG900.
Environmental note o The packaging materials that Baumatic uses are environmentally friendly and can be recycled. o Please discard all packaging material with due regard for the environment.
Important safety information Your safety is of the utmost importance to Baumatic. Please make sure that you read this instruction booklet before attempting to install or use the appliance. If you are unsure of any of the information contained in this booklet, please contact the Baumatic Customer Care Department. General Information o This appliance is designed for domestic household use and for the cooking and frying of domestic foodstuffs.
Child Safety o Baumatic strongly recommend that babies and young children are prevented from being near to the appliance and not allowed to touch the appliance at any time. During and after use, all surfaces will be hot. o If it is necessary for younger family members to be in the kitchen, please ensure that they are kept under close supervision at all times. o Older children should only be allowed to utilise the appliance when supervised.
o Great care should be taken whilst using this appliance and when following the cleaning procedure. o You should not use a steam jet or any other high pressure cleaning equipment to clean the appliance. Installation This appliance must be correctly installed by a GASSAFE registered installer, strictly in accordance with the manufacturer’s instructions and the relevant British Standards. Please see the specific section of this booklet that refers to installation.
Specifications – BHG300.5SS Product dimensions: Depth: Width: Height: 510 mm 288 mm 45 mm Aperture dimensions: Depth: Width: 494 mm 270 mm Product specifications: o o o o o o 1 x 3.00 kW rapid burner 1 x 1.00 kW auxiliary burner Front control operation Enamelled pan stands Automatic ignition Flame failure safety device on each burner Standard accessories: o LPG conversion jets Gas hob surface layout 1 = 1.00 kW auxiliary burner 2 = 3.
Specifications – BHG604.5SS/W Product dimensions: Aperture dimensions: Depth: Width: Height: Depth: Width: 510 mm 620 mm 50 mm 480 mm 560 mm Product specifications: o o o o o o o 1 x 3.00 kW rapid burner 2 x 1.75 kW semi-rapid burners 1 x 1.00 kW auxiliary burner Front control operation Enamelled pan stands Automatic ignition Flame failure safety device on each burner Standard accessories: o LPG conversion jets Gas hob surface layout 1 2 3 4 = = = = 1.75 1.75 3.00 1.
Specifications – BHG610.5SS Product dimensions: Aperture dimensions: Depth: Width: Height: Depth: Width: 510 mm 620 mm 50 mm 480 mm 560 mm Product specifications: o o o o o o o o 1 x 3.50 kW triple crown (wok) burner 1 x 1.75 kW semi-rapid burners 1 x 3.00 kW rapid burner 1 x 1.
Specifications – BHG710.5SS Product dimensions: Aperture dimensions: Depth: Width: Height: Depth: Width: 510 mm 720 mm 50 mm 480 mm 560 mm Product specifications: o o o o o o o o 1 x 3.00 kW rapid burner 2 x 1.75 kW semi-rapid burners 1 x 1.00 kW auxiliary burner 1 x 3.
Specifications – BHG900.5SS Product dimensions: Aperture dimensions: Depth: Width: Height: Depth: Width: 510 mm 909 mm 50 mm 480 mm 840 mm Product specifications: o o o o o o o o 1 x 3.00 kW rapid burner 2 x 1.75 kW semi-rapid burners 1 x 1.00 kW auxiliary burner 1 x 3.
Electrical details Rated Voltage: Supply Connection: Mains Supply Lead: 230 Vac 50 Hz 3A (double pole switched fused outlet with 3mm contact gap) 3 core x 1.5 mm² Gas details Connection: Type: Rp ½ (ISO R7) Natural Gas (20 mbar) Alternative LPG G30 (28-30/37 mbar) For future reference please record the following information which can be found on the rating plate and the date of purchase which can be found on your sales invoice. The rating plate of your hob is located on the underneath of the appliance.
Using the gas hob Before first use IMPORTANT: You should clean the hob surface (see “Cleaning and maintenance” section). The gas hob The following symbols will appear on the control panel, next to each control knob: Circle: gas off Large flame: maximum setting / ignition position Small flame: minimum setting o The minimum setting is at the end of the anti-clockwise rotation of the control knob. o All operation positions must be selected between the maximum and minimum position.
Automatic ignition with flame failure safety device The appliance is fitted with a flame failure safety device on each burner, which is designed to stop the flow of gas to the burner head in the event of the flame going out. To ignite a burner: o Press in the control knob of the burner that you wish to light and turn it anti-clockwise to the maximum position. o If you keep the control knob depressed, the automatic ignition for the burner will operate.
Energy saving tips Burners Pan Ø min Wok 200 mm Rapid 200 mm Semi-rapid 140 mm Auxiliary 100 mm size Ø max 320 mm 260 mm 200 mm 140 mm o The diameter of the bottom of the pan should correspond to that of the burner. o The burner flame must never extend beyond the diameter of the pan. o Use flat bottomed pans only. o When possible, keep a lid on the pan whilst cooking. o Cook vegetables with as little water as possible, to reduce cooking times.
Cleaning Cleaning operations must only be carried out when the hob is cool. The appliance should be disconnected from your mains supply before commencing any cleaning process. Cleaning the hob top Any residues that are left on the hob top surface from cleaning agents will damage it. You should remove any residues with warm soapy water. Abrasive cleaners or sharp objects will damage the hob surface; you should clean it using warm soapy water.
o Soak them for about ten minutes in hot water and a little detergent. o After cleaning and washing them, wipe and dry them carefully. o Before placing the burners back on the hob top, make sure that the gas jet is not blocked. o IMPORTANT: Make sure that you reassemble the burners in the original way. Maintaining the enamelled pan stands (BHG300.5SS / BHG604.5SS/W) o IMPORTANT: Make sure that the hob surface and pan stands have cooled before you attempt to touch them.
Installation The installation must be carried out by a GASSAFE registered installer, in accordance with the current version of the following.
Positioning The adjacent furniture must be able to withstand a minimum temperature rise of 85°C above the ambient temperature of the room it is located in, during periods of use. o This appliance can be located in a kitchen, a kitchen diner or a sitting room. IMPORTANT: The appliance must not be installed in a bathroom or shower room. This appliance is classified as Class 3 and therefore is to be built into a kitchen unit (depending on size) or 600 mm worktop that is between 25 mm and 40 mm thick.
Unpacking the appliance When unpacking the appliance please check that the following items are contained within the packaging: 1 x Baumatic hob Pan stands Burner assemblies Instruction manual Warranty card Fixing screws Clamps Sealing strip LPG conversion jets Self-adhesive label for amending the gas category on the appliance’s rating plate (required if the LPG conversion jets are used). Installing the appliance o Cut a hole in the worktop that corresponds with the correct model drawing: BHG300.5SS BHG710.
o Carefully turn the hob upside down and place it on a cushioned mat. o Apply the sealing strip provided around the edge of the appliance. o The protective covering must be removed from both sides. o Do not leave a gap in the sealing agent or overlap the thickness. o IMPORTANT: Do not use a silicon sealant to seal the appliance against the aperture. This will make it difficult to remove the hob from the aperture in future, particularly if it needs to be serviced.
o On the underneath of the hob, adjust the clamps into a position that is suitable for your worktop. Then fully tighten the screws (C) to secure the hob into position. Gas connection This appliance must be installed by a competent person in accordance with the current versions of the following UK (United Kingdom) or ROI (Republic of Ireland) Regulations and Safety Standards or their European Norm Replacements.
o If the room has a volume of less than 5m³, it will require an air vent of 100cm² (effective area). o If it is installed in a room with a volume that exceeds 11m³, then no air vent is required. o If there are any other fuel burning appliances in the same room the current edition of BS 5440: Part 2: should be consulted to determine air vent requirements.
o Put the gas seal into the elbow. o Fully tighten the elbow and seal onto the gas rail. o The elbow MUST be pointing in a downwards direction. o Gas pressure may be checked on a semi-rapid hob burner. Remove the appropriate injector and attach a test nipple. Light the other burners and observe that the gas pressure complies with the gas standards in force. o IMPORTANT: On completion carry out a gas soundness test. Gas adjustment (Conversion to LPG) All work must be registered engineer.
GAS TYPE PRESSURE BURNER mbar Natural gas – G20 LPG – G30/G31 20 28-30/37 Triplecrown Rapid Semirapid Auxiliary Triplecrown Rapid Semirapid Auxiliary Ø INJECTOR 1/100 mm 141 THERMAL CAPACITY Nominal W 3500 333 129 101 3000 1750 286 167 77 94 1000 3500 95 254 87 66 3000 1750 218 127 50 1000 73 CONSUMPTION l/h g/h o Reassemble all the burners carefully; in particular you should make sure that the flame spreader is correctly placed on the burner.
o Unscrew the adjusting screw, in order to increase the gas flow or tighten the adjusting screw to decrease the gas flow. o The correct adjustment is obtained when the flame has a length of about 3 – 4 mm. o For butane/propane gas, the adjusting screw must be tightly screwed in. o Refit the control knob. o Make sure that the flame does not go out by quickly turning from maximum flow to minimum flow.
If it becomes necessary to replace a gas tap, then you should proceed as follows: o Remove the control knobs, pan supports, burners, hob fixing screws and clamps. o Remove the hob from the worktop and remove any underside protective covers. o Disconnect the fixings holding the tap to the fascia panel and separate the assembly. o Disconnect the gas pipe from the gas tap, and then disassemble them from the gas rail by removing the fixing screws. o When fitting a new tap, ensure that a new gasket is used.
Replacing the mains supply cable If the mains supply cable is damaged, then it must be replaced by an appropriate replacement which can be obtained from the Spares Department. The mains supply cable should be replaced in accordance with the following instructions: o Switch the appliance off at your mains supply. o Open the box of the supply board. o Unscrew the clamp fixing the cable. o Replace the cable with one of the same length and in accordance with the specification given above.
My appliance isn’t working correctly IMPORTANT: If your appliance appears not to be operating correctly, then you should disconnect it from your mains supply and then contact the Baumatic Customer Care Department on telephone number 0844 692 3605. DO NOT ATTEMPT TO REPAIR THE APPLIANCE YOURSELF.
6 Bennet Road, Reading, Berkshire RG2 0QX United Kingdom Customer Care Telephone 0844 692 3605 Spares Telephone 0844 692 3606 Website: www.baumatic.co.
cod. 1.008.89.0 www.baumatic.co.
