BHG620SS / BHG690SS / BHG625SS / BHG695SS / BHG720SS / BHG790SS Gas hobs el 1
User Manual for your Baumatic BHG620SS / BHG625SS / BHG690SS / BHG695SS 60 cm 4 Burner gas hob BHG720SS / BHG790SS 70 cm 5 Burner gas hob NOTE: This User Instruction Manual contains important information, including safety & installation points, which will enable you to get the most out of your appliance. Please keep it in a safe place so that it is easily available for future reference; for you or any person not familiar with the operation of the appliance.
Contents Environmental note 4 Important safety information 5–7 Specifications BHG620SS / BHG690SS BHG625SS / BHG695SS BHG720SS BHG790SS Electrical details Gas details Gas hob surface layout 8 – 13 8 9 10 11 11 12 12 - 13 Using the gas hob Before first use Switching the hob on Automatic ignition with flame failure device Energy saving tips 13 - 15 13 13 - 14 14 14 - 15 Cleaning Cleaning the hob top After each use Cleaning the hob burners Maintaining the cast iron pan stands 15 - 16 15 16 16 16 Inst
Environmental note o The packaging materials that Baumatic uses are environmentally friendly and can be recycled. o Please discard all packaging material with due regard for the environment.
Important safety information Your safety is of the utmost importance to Baumatic. Please make sure that you read this instruction booklet before attempting to install or use the appliance. If you are unsure of any of the information contained in this booklet, please contact the Baumatic Advice Line. General Information o This appliance is designed for domestic household use and for the cooking and frying of domestic foodstuffs.
Child Safety o Baumatic strongly recommend that babies and young children are prevented from being near to the appliance and not allowed to touch the appliance at any time. During and after use, all surfaces will be hot. o If it is necessary for younger family members to be in the kitchen, please ensure that they are kept under close supervision at all times. o Older children should only be allowed to utilise the appliance when supervised.
Cleaning o Cleaning of the hob should be carried out on a regular basis. o IMPORTANT: Before attempting to clean the appliance, it should be disconnected from the mains and cool. o Great care should be taken whilst using this appliance and when following the cleaning procedure. o You should not use a steam jet or any other high pressure cleaning equipment to clean the appliance.
Specifications BHG620SS / BHG690SS Product dimensions: Aperture dimensions: Depth: Width: Height: Depth: Width: 510 mm 600 mm 40 mm 480 mm 560 mm Product specifications: o 1 x 3.00 kW rapid burner o 2 x 1.75 kW semi-rapid burners o 1 x 1.
BHG625SS / BHG695SS Product dimensions: Aperture dimensions: Depth: Width: Height: Depth: Width: 510 mm 600 mm 40 mm 480 mm 560 mm Product specifications: o 1 x 3.80 kW triple crown (wok) burner o 2 x 1.75 kW semi-rapid burners o 1 x 1.
BHG720SS / BHG790SS Product dimensions: Aperture dimensions: Depth: Width: Height: Depth: Width: 510 mm 700 mm 40 mm 480 mm 560 mm Product specifications: o o o o 1 1 2 1 x x x x 3.80 3.00 1.75 1.
Electrical details Rated Voltage: Supply Connection: Max Rated Inputs: Mains Supply Lead: 220 - 240 Vac 50 / 60 Hz 3 A (double pole switched fused outlet with 3mm contact gap) 0.0008 kW 3 core x 0.75mm² (Type RR-F marked) Gas details Connection: Type: Rp ½ (ISO R7) Natural Gas (20 mbar) Alternative LPG G30 (28-30/37 mbar) For future reference please record the following information which can be found on the rating plate and the date of purchase which can be found on your sales invoice.
BHG625SS / BHG695SS A = 3.80 kW triple crown (wok) burner B = 1.75 kW semi-rapid burner C = 1.00 kW auxiliary burner D = Control panel BHG720SS / BHG790SS A = 3.80 kW triple crown (wok) burner B = 3.00 kW rapid burner C = 1.75 kW semi-rapid burner D = 1.00 kW auxiliary burner E = Control panel Using the gas hob Before first use IMPORTANT: You should clean the hob surface (see “Cleaning and maintenance” section).
o The minimum setting is at the end of the anti-clockwise rotation of the control knob. o All operation positions must be selected between the maximum and minimum position. o Never select a knob position between the maximum and off position. o The symbol on the control panel, next to the control knob will indicate which gas burner it operates.
o The diametre of the bottom of the pan should correspond to that of the burner. o The burner flame must never extend beyond the diametre of the pan. o Use flat bottomed pans only. o When possible, keep a lid on the pan whilst cooking. o Cook vegetables with as little water as possible, to reduce cooking times. IMPORTANT: Always place pans centrally over the hob burners and position them so that the handles cannot get accidentally caught or knocked off.
After each use o Remove the pan stands and wipe the appliance over with a soft, damp cloth that has been put into warm soapy water. The cloth should be wrung out after being taken out of the soapy water. o Dry the appliance by rubbing the surface with a soft, clean cloth. o We would recommend that an appropriate stainless steel cleaner and polish is regularly used on the stainless steel surfaces of this appliance.
Installation The installation must be carried out by a GASSAFE registered installer, in accordance with the current version of the following.
Positioning The adjacent furniture must be able to withstand a minimum temperature rise of 85°C above the ambient temperature of the room it is located in, during periods of use. * 600 mm (BHG620SS / BHG690SS / BHG625SS / BHG695SS) * 700 mm (BHG720SS / BHG790SS) o This appliance can be located in a kitchen, a kitchen diner or a bed sitting room. IMPORTANT: The appliance must not be installed in a bathroom or shower room.
o 50 mm clearance around the appliance and between the hob surface and any combustible materials. Unpacking the appliance When unpacking the appliance please check that the following items are contained within the packaging: 1 x Baumatic hob Pan stands Burner assemblies Instruction manual Baumatic warranty card Fixing screws Clamps Sealing strip LPG conversion jets Self-adhesive label for amending the gas category on the appliance’s rating plate (required if the LPG conversion jets are used).
BHG625SS / BHG695SS BHG720SS / BHG790SS o Cut a hole in the worktop that corresponds with the relevant drawing for your hob on pages 19 - 20.
All models o IMPORTANT: You must have a gap of at least 25 mm between the underneath of the appliance and any surface that is below it. o Carefully turn the hob upside down and place it on a cushioned mat. o Apply the sealing strip (A) provided around the edge of the appliance. o The protective covering must be removed from both sides. o Do not leave a gap in the sealing agent or overlap the thickness. o IMPORTANT: Do not use a silicon sealant to seal the appliance against the aperture.
o Place the clamp (B) over the holes that match the size of the screws. There are one set of screw holes in each corner of the hob. Slightly tighten a screw (C) through the clamp (B) so that the clamp is attached to the hob, but so that you can still adjust the position of it. o Carefully turn the hob back over and then gently lower it into the aperture hole that you have cut out. o On the underneath of the hob, adjust the clamps into a position that is suitable for your worktop.
Ventilation requirements o The room containing the hob should have an air supply in accordance with the current edition of BS 5440: Part 2: o The room must have opening windows or equivalent; some rooms may also require a permanent vent. o If the room has a volume between 5 and 10m³, it will require an air vent of 50cm² (effective area). Unless it has a door which opens directly to the outside. o If the room has a volume of less than 5m³, it will require an air vent of 100cm² (effective area).
Gas Safety (Installation and Use) Regulations IMPORTANT: The appliance MUST be connected to the gas supply by use of a 15 mm x ½” female coupler, seal, copper pipe and an isolation tap fitted in an easily accessible position. o It is the law that all gas appliances are installed by competent persons in accordance with the current edition of the Gas Safety Installation and Use Regulations. o It is in your interest and that of safety to ensure compliance with the law.
Gas adjustment (Conversion to LPG) All work must be registered engineer. carried out by a GASSAFE IMPORTANT: Always isolate the hob from the electricity supply before changing the injectors and/or adjusting the minimum flow of the burners. o Remove the pan-stands, burners and flame spreaders (A). o Unscrew the injector (B) and replace it with the stipulated injector for the new gas supply (see table on next page). GENERAL INJECTORS TABLE Kind of gas Nozzle Burners Power (in watts) mm/100 Max. Min.
o IMPORTANT: The minimum flow adjustment process must be completed before the appliance is next used. Minimum flow adjustment for hob gas taps. All work must be registered engineer. carried out by a GASSAFE IMPORTANT: Always isolate the hob from the electricity supply before changing the injectors and/or adjusting the minimum flow of the burners. o Switch the burner on and set the knob at the minimum position.
Gas tap maintenance These maintenance operations MUST ONLY be carried out by a GASSAFE registered engineer. IMPORTANT: Before carrying out any maintenance operations, disconnect the appliance from the gas and electricity supplies. If a gas tap becomes stiff to operate, then you should proceed as follows: o Remove the control knobs, pan supports, burners, hob fixing screws and clamps. o Remove the hob from the worktop and remove any underside protective covers.
o Reconnect the gas tap, perform a gas soundness test and then reassemble the hob. Electrical connection This appliance must be installed by a qualified person in accordance with the latest edition of the I.E.E. Regulations and in compliance with Baumatic’s instructions. Before connecting the appliance, make sure that the supply voltage marked on the rating plate corresponds with your mains supply voltage. o Cable type: H05 RRF 3 core x 0.75 mm³ (Type RR-F marked).
My appliance isn’t working correctly IMPORTANT: If your appliance appears not to be operating correctly, then you should disconnect it from your mains supply and then contact the Customer Care Department on telephone number (0118) 933 6911. DO NOT ATTEMPT TO REPAIR THE APPLIANCE YOURSELF. Please note that if an engineer is asked to attend whilst the product is under guarantee and finds that the problem is not the result of an appliance fault, then you may be liable for the cost of the call out charge.
Baumatic Consumables o BC001 Degreaser for Dishwashers (200 g) o BC002 Descaler for Washing Machines and Dishwashers (200 g) o BC003 Ceramic Hob Cleaner (250 ml) o BC004 Oven Cleaner (250 ml) o BC005 Stainless Steel Cleaner and Protector (250 ml) o BC007 E-Cloth – General Purpose Cloth o BC008 Microwave Cover To order a Baumatic consumable product please call 0123 5437 244 and quote the product code. You can also order online from eshop.baumatic.co.
United Kingdom Baumatic Ltd., Baumatic Buildings, 6 Bennet Road, Reading, Berkshire RG2 0QX United Kingdom Sales Telephone (0118) 933 6900 Sales Fax (0118) 931 0035 Customer Care Telephone (0118) 933 6911 Customer Care Fax (0118) 986 9124 Spares Telephone (01235) 437244 Advice Line Telephone (0118) 933 6933 E-mail: sales@baumatic.co.uk customercare@baumatic.co.uk spares@baumatic.co.uk technical@baumatic.co.uk Website: www.baumatic.co.uk Facebook: www.facebook.com/baumatic.
