BHS320.
User Manual for your Baumatic BHS320.5SS 30cm 2 Solid plate electric hob NOTE: This User Instruction Manual contains important information, including safety & installation points, which will enable you to get the most out of your appliance. Please keep it in a safe place so that it is easily available for future reference; for you or any person not familiar with the operation of the appliance.
Contents Environmental note 4 IMPORTANT SAFETY INFORMATION 5–8 Specifications Product and aperture dimensions Product specifications Electrical details Hob surface layout 8-9 8 8 9 9 Using the hob Before first use Control knobs Switching on a zone and setting a power level Hob guidelines 10 - 12 10 10 10 11 – 12 Cleaning and maintenance Cleaning the hob top After each use Using a specialist hob cleaner Maintaining the solid plates 12 - 13 12 12 13 13 Installation Positioning Unpacking the applianc
Environmental note o The packaging materials that Baumatic uses are environmentally friendly and can be recycled. o Please discard all packaging material with due regard for the environment.
IMPORTANT SAFETY INFORMATION Your safety is of the utmost importance to Baumatic. Please make sure that you read this instruction booklet before attempting to install or use the appliance. If you are unsure of any of the information contained in this booklet, please contact the Baumatic Advice Line. General Information o This appliance is designed for domestic household use and for the cooking and frying of domestic foodstuffs.
Child Safety o Baumatic strongly recommend that babies and young children are prevented from being near to the appliance and not allowed to touch the appliance at any time. During and after use, all surfaces will become hot. o If it is necessary for younger family members to be in the kitchen, please ensure that they are kept under close supervision at all times. o Older children should only be allowed to utilise the appliance when supervised.
Cleaning o Cleaning of the hob should be carried out on a regular basis. o IMPORTANT: Before attempting to clean the appliance, it should be disconnected from the mains and allowed to cool. o Great care should be taken whilst using this appliance and when following the cleaning procedure. o You should not use a steam jet or any other high pressure cleaning equipment to clean the appliance.
Specifications Product dimensions: Aperture dimensions: Depth: Width: Height: Depth: Width: 510 mm 290 mm 52 mm 480 mm 260 mm Product specifications: o 1 x 1.50 kW rapid plate (Ø 155 mm) o 1 x 1.
Hob surface layout A) B) C) D) 1.50 kW rapid plate (Ø 188 mm) 1.50 kW rapid plate (Ø 155 mm) Power on indicator light Control knob Electrical details Rated Voltage: Supply Connection: Max Rated Inputs: Mains Supply Lead: 230-240 Vac, 50-60 Hz 13A (double pole switched fused outlet with 3mm contact gap) 3.00 kW 3 core x 1.
Using the hob Before first use IMPORTANT: You should clean the hob surface and solid plates (see “Cleaning and maintenance” section). o You should switch on one cooking zone at a time, for 5 minutes at the maximum setting. This will help to eliminate any new smell that exists and evaporate any humidity that has formed on the heating elements during transit. o When doing this burn off process, an appropriately sized saucepan containing cold water should be placed on the zone in question.
Hob guidelines o The first few times the hob top is used, it may give off an acrid, burning smell. This smell will disappear completely with repeated use. o The hob surface is fitted with cooking areas of different diametre. o The positions where the heat will radiate from are clearly marked on the hob top. The saucepans must be positioned exactly on these zones for efficient heating to occur. Pans should have the same diametre as the cooking zone that they are being used on.
Cleaning and maintenance Cleaning and maintenance operations must only be carried out when the hob is cool. The appliance should be disconnected from your mains supply before commencing any cleaning process. Cleaning the hob top Any residues that are left on the hob top surface from cleaning agents will damage it. You should remove any residues with water and a little washing up liquid.
Maintaining the solid plates o If something is spilt onto the plate itself, then it can be removed using a soft brush, plastic or nylon scourer and warm water. o To keep the solid plates in good condition, you should put a little olive oil onto a kitchen towel and rub it onto the surface of the plate. The next time the plate is used, it may produce a little smoke. o Alternatively you can use a hotplate conditioner; these products can normally be found at larger supermarkets and hardware stores.
Positioning The adjacent furniture must be able to withstand a minimum temperature rise of 100°C above the ambient temperature of the room it is located in, during periods of use. This appliance is classified as Class 3 and therefore is to be built into a kitchen unit (depending on size) or 600 mm worktop that is at least 38 mm thick. The following minimum clearance distances must be observed:o 700 mm between the hob surface and the underside of any horizontal surface above it.
Installing the appliance o Cut a hole in the worktop that corresponds with the drawing shown above. o IMPORTANT: You must observe the ventilation requirements shown in the drawing opposite. o IMPORTANT: Do not use a silicon sealant to seal the appliance against the aperture. This will make it difficult to remove the hob from the aperture in future, particularly if it needs to be serviced.
o IMPORTANT: There are ventilation holes around the outside of the hob. YOU MUST ensure that these holes are not blocked by the work top, when you put the hob into position (see drawing opposite). o Carefully turn the hob upside down and place it on a cushioned mat. o The supplied brackets need to be fitted to each of the four corners on the underside of the hob. o Place a bracket onto each corner, ensuring that the outer hole lines up with the hole on the corner of the hob.
Electrical connection YOUR HOB IS INTENDED PERMANENT INSTALLATION. FOR o Cable type: H05 RRF 3 core x 1.5 mm² marked). FITTED AND (Type RR-F o Before connecting the appliance, make sure that the supply voltage marked on the rating plate corresponds with your mains supply voltage. o We recommend that the appliance is connected by a qualified electrician, who is a member of the N.I.C.E.I.C. and who will comply with the I.E.E. and local regulations. o WARNING: THIS APPLIANCE MUST BE EARTHED.
o As the colours of the wires in the appliance’s mains lead may not correspond with the coloured markings identifying the terminals in your spur box, please proceed as follows: The brown wire must be connected to the terminal marked “L” (live), or coloured red. The blue wire must be connected to the terminal marked “N” (neutral), or coloured black. The green and yellow wire must be connected to the terminal marked “E” (earth), or by the earth symbol, or coloured green and yellow.
IMPORTANT: If your appliance appears not to be operating correctly, then you should disconnect it from your mains supply and then contact the Customer Care Department on telephone number (0118) 933 6911. DO NOT ATTEMPT TO REPAIR THE APPLIANCE YOURSELF. Please note that if an engineer is asked to attend whilst the product is under guarantee and finds that the problem is not the result of an appliance fault, then you may be liable for the cost of the call out charge.
Baumatic Consumables o BC001 Degreaser for Dishwashers (200 g) o BC002 Descaler for Washing Machines and Dishwasher (200 g) o BC003 Ceramic Hob Cleaner (250 ml) o BC004 Oven Cleaner (250 ml) o BC005 Stainless Steel Cleaner and Protector (250 ml) o BC007 E-Cloth – General Purpose Cloth o BC008 Microwave Cover To order a Baumatic consumable product please call 0123 5437 244 and quote the product code. You can also order online from eshop.baumatic.co.
United Kingdom Baumatic Ltd., Baumatic Buildings, 6 Bennet Road, Reading, Berkshire RG2 0QX United Kingdom Czech Republic Baumatic CR spol s.r.o. Lípovà 665 460 01 Liberec 4 Czech Republic +420 483 577 200 www.baumatic.cz Sales Telephone (0118) 933 6900 Sales Fax (0118) 931 0035 Customer Care Telephone (0118) 933 6911 Customer Care Fax (0118) 986 9124 Spares Telephone (01235) 437244 Advice Line Telephone (0118) 933 6933 Slovakia Baumatic Slovakia, s.r.o.