BR16.2A Built-in Larder Fridge Downloaded from Fridge-Manual.
User Manual for your BR16.2A BUILT-UNDER LARDER FRIDGE NOTE: This User Instruction Manual contains important information, including safety & installation points, which will enable you to get the most out of your appliance. Please keep it in a safe place so that it is easily available for future reference. 1 Downloaded from Fridge-Manual.
CONTENTS YOUR APPLIANCE’S SPECIFICATIONS …….…….3 SAFETY INFORMATION / ENVIRONMENTAL NOTE .. 4 USING YOUR FRIDGE……………….……………..…………5-8 YOUR BR16.2A FRIDGE …………………….………………….5 BEFORE USING YOUR FRIDGE…………….……………….…6 USING YOUR FRIDGE……………..……………………….…7-8 ARRANGING FOOD IN YOUR FRIDGE …………………9-10 NOTES ON USING YOUR FRIDGE ………………………….11 CLEANING AND MAINTENANCE……….………………12-13 DEFROSTING / TIPS FOR SAVING ENERGY…………14 INSTALLING YOUR FRIDGE……………………………...….15 FITTING THE DÉCOR DOOR …………………………...
Specifications of your BR16.2A Built-in fridge Congratulations on purchasing a Baumatic BR16.
Important Safety Information: Please Read this before installing & using. ELECTRICAL SAFETY • • • NOTE - This appliance must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance of electrical current. You will be able to tell if it is because a non-grounded appliance will give off an electrical discharge. Manufacturer declines all responsibility for any damage due to nongrounding of appliance.
Using your Baumatic BR16.2A LARDER-FRIDGE Your BR16.2A Built-under Larder-Fridge: KEY A 1 SHELF: The shelves may be placed in any of the guide slots within the interior of the appliance. They are protected from sliding out. To remove a shelf, simply lift the front of the shelf and carefully pull it out of the grooves. Quickly perishable food should be stored at the back (the coldest part of your refrigerator) but not touching the back wall.
NOTE: BEFORE Using your BR16.2A LARDER-FRIDGE: UPON DELIVERY: When your Fridge has been delivered, you will need to wait approximately 2 hours before turning it on. The fluid of the compressor installed in the appliance will need time to settle. PLEASE DO NOT PLUG IN ANY EARLIER THAN THIS! NOTE: THERE CAN BE AN ODOUR WHEN YOU FIRST SWITCH ON THE APPLIANCE. IT WILL VANISH WHEN THE UNIT STARTS COOLING.
USING your Baumatic BR16.2A FRIDGE YOU SWITCH ON YOUR APPLIANCE by PLUGGING IT IN & SETTING THE THERMOSTAT inside the Fridge at the upper righthand side: Your Fridge’s thermostat automatically regulates the inside temperature of the compartments. By rotating the thermostat knob from a low to a higher number position, colder temperatures can be obtained. Refrigerator Thermostat setting Note: Turning the knob setting towards 7 will make all the compartments of your fridge colder.
USING your Baumatic BR16.2A LARDER-FRIDGE Reminder: Allow the unit time to settle after delivery. If your plug and power socket are now behind the fridge and you still need to move the unit into place, be especially careful. Remember to leave a safe distance between the back of the fridge and the wall or rear of the unit cabinet. o You switch your fridge OFF by turning the thermostat knob to position ‘0’.
ARRANGING FOOD IN YOUR FRIDGE • To reduce humidity and the consequent increase of frost, NEVER place liquids in unsealed containers in the refrigerator. Frost tends to concentrate in the coldest parts of the evaporator. In time, the unit will need more frequent defrosting if too much humidity develops inside it. • Foods should be properly packed so as to prevent mixing various degrees of moisture and odours.
ARRANGING FOOD IN YOUR FRIDGE • DO NOT ALLOW anything to touch the refrigerator’s back wall as it will cause frost. Also, packaging, especially paper, can stick to it and spoil. • Crispy and delicate foods should be stored in the coldest parts of the fridge. • DO NOT open the refrigerator door too often or leave it open for long spells of time. • ARRANGE meat and cleaned fish (wrapped in packages or sheets of plastic) which you will then use within 1-2 days.
NOTES ON USING YOUR FRIDGE ALWAYS Cover and wrap foods, especially if they are PUNGENT. • DO NOT place paper or plastic on the shelves which would block the flow of air through the grids. NOTE: At the maximum cold setting, with a high outside (ambient) temperature and well-stocked (full or nearly full) compartments, the Fridge’s operation may be continuous, leading to the formation of some frost on the evaporator.
CLEANING / MAINTENANCE NOTE: Before attempting to clean your appliance, UNPLUG IT and make sure you do the following: WE RECOMMEND THAT YOU CLEAN AND MAINTAIN YOUR REFRIGERATOR ONCE A MONTH. 9 Pay particular attention to the sealing rubber bars of the doors. These need to be kept clean for hygienic reasons as well as to allow the door to close properly. 9 Leave the door open during cleaning. 9 Soak up the water using a sponge.
CLEANING / MAINTENANCE HOW TO CLEAN THE CONDENSER – the condenser consists of a coil structure at the back of your freezer. To clean it, carefully follow the following instructions: To optimize the operation of the appliance and to save energy you should periodically clean the dust from the condenser at the back of the appliance. CAUTION: You will need to move your fridge forward from its cabinet housing to gain access to the condenser at the rear of your appliance.
Do not remove the drain pan while cleaning it! DEFROSTING - Defrosting occurs fully automatically in the refrigerator compartment during normal operation. The defrosted water collected by the evaporating tray evaporates automatically. TIPS FOR ENERGY SAVINGS 9 Try not to open the door too often, especially when the weather is wet and hot. Once you open the door, be sure to close it as soon as possible. 9 Use higher thermostat settings only if essential and not for constant, long-term use.
INSTALLING YOUR BR16.2A REFRIGERATOR NOTE – YOU NEED THE SPACES SHOWN HERE TO INSTALL YOUR APPLIANCE. NOTE: Ensure there is sufficient space (36mm) behind the cooling coils at the back of your Fridge. NOTE: Ensure that you are going to be placing your fridge away from heat sources and in a well-ventilated position. This should be at least 3 cm away from electric or gas stoves and 30 cm from oil or coal stoves. Note – you will have to remove the rear wall of your cabinet unit.
INSTALLING YOUR APPLIANCE- CONTINUED Fitting Bar Install the Fitting Bar (shown in the picture below), so that it attaches to the top of the appliance and underneath the top of the cabinetry, indicated by the arrow: *Please be aware that the Fitting Bar is not attached to the appliance and needs to be secured during installation. 16 Downloaded from Fridge-Manual.
INSTALLING YOUR BR16.2A REFRIGERATOR Fitting the Décor Door - 1) Widely open the fridge door & hold it against the kitchen unit door. 2) Fix the slide guides (attached in a plastic bag along with the screws ST 4.2 x 9.5) to the edge of the door. Cover the open holes with the attached caps. 3) Hold the appliance door to the décor door. 4) Insert the slides into the guides and fix them on the kitchen unit door some 15mm from the edge, using the A 4 x 12 screws (Fig. 3, at right).
INSTALLING YOUR BR16.2A REFRIGERATOR 6) 7) 8) Fix the slides, being careful not to move them while fixing them into place (Fig. 4, at left). Fix the slide guides to the original position. Close the door and check the gasket (it should not be creased). The door should open and close smoothly. Affixing the door to your Cabinet Fix the appliance to the kitchen unit. On the upper side, fix the three screws A 4 x 12 through the rail and on the lower side with two screws A 4 x 16, through the lower hinges.
Reversing the Swing of the Door Reversing the swing of the Door 3) Replace the fastener (6) and the washer (5) in reverse order into the opening of the lower hinge on the opposite side of the appliance. 4) Take off all door corners (8 & 9) and interchange them (instead of the corner with a hole (9), insert the one without the hole (8), and vice versa). 5) Put the door of the appliance on the lower hinge (7). 6) Fix the upper hinge (2) and cover it.
Troubleshooting seal can be stretched and ‘fluffed’ outward. Trace a problem using the table below instead of having to call for help. PROBLEM WHAT TO DO CHECK THAT THE PLUG IS WELL-INSERTED INTO THE POWER SOCKET CHECK THAT THERE IS POWER FROM THE MAINS – THERE MAY BE A BLACKOUT OR YOUR FUSES MAY HAVE BLOWN.
FLOWING. THIS IS NOT A MALFUNCTION. PROBLEM ICE FORMATION ON THE INNER REAR WALL WHAT TO DO IN THE UNLIKELY EVENT THAT ICE DOES FORM ON THE INNER BACK WALL, IT SHOULD BE MANUALLY REMOVED WHEN IT REACHES 3-5MM THICK, USING A PLASTIC SCRAPER. MAKE SURE YOU TURN THE THERMOSTAT DOWN TO ‘OFF’ OR ‘0’ FIRST. NEVER USE ELECTRIC DEVICES FOR DEFROSTING OR DEFROSTING SPRAYS. IN CASE THE DISCHARGE WATER OUTLET BECOMES CLOGGED, OR THE DEFROSTED WATER DRIPS OVER THE CHANNEL, WATER WILL LEAK FROM THE FRIDGE.
22 Downloaded from Fridge-Manual.
BAUMATIC LTD. -CONDITIONS OF GUARANTEE. Dear Customer, The conditions of guarantee which apply to your Baumatic appliance are as follows: This product is guaranteed for 12 months from the date of original purchase. Baumatic Ltd will repair any defect that arises due to faulty materials or workmanship free of charge during this period. *In addition, your appliance is covered by a 5 year parts warranty.
Baumatic Ltd Make-up for your kitchen Headquarters Baumatic Ltd. Baumatic Buildings, 6 Bennet Road, Reading, Berkshire RG2 0QX, United Kingdom Sales Telephone +44 118 933 6900 Sales Fax +44 118 931 0035 Service Telephone +44 118 933 6911 Service Fax +44 118 986 9124 Spares Telephone +44 118 933 6922 Technical / Advice Telephone +44 118 933 6933 E-mail: sales@baumatic.co.uk technical@baumatic.co.uk Http (Internet site): www.baumatic.com 24 Downloaded from Fridge-Manual.
25 Downloaded from Fridge-Manual.
26 Downloaded from Fridge-Manual.
