BT85.
User Manual for your Baumatic BT85.1GL Cooker Hood 90 cm Chimney Hood in Stainless Steel NOTE: This User Instruction Manual contains important information, including safety & installation points, which will enable you to get the most out of your appliance. Please keep it in a safe place so that it is easily available for future reference.
CONTENTS YOUR COOKER HOOD’S SPECIFICATIONS ….……………..………….3 IMPORTANT SAFETY INFORMATION……………………………….…4-5 CARING FOR THE ENVIRONMENT…………………………………………6 USING YOUR COOKER HOOD………………………………..……………..7 MAINTAINING AND CLEANING YOUR COOKER HOOD ……….8-10 INSTALLATION INSTRUCTIONS ……………………….……...….12-19 ELECTRICAL CONNECTION……………12 INSTALLING THE COOKER HOOD………13-15 FITTING THE CHIMNEY…………………16-17 ATTACHING THE GLASS…..18 INSTALLATION NOTES – EXTRACTION / PURIFYING VERSION .….
Specifications of your BT85.1GL Cooker Hood Congratulations on purchasing a Baumatic Cooker Hood! To fully enjoy using your appliance long into the future, please firstly familiarise yourself with its specifications, safety advice and operational instructions included in this manual. You will also need this manual to ensure that your Cooker Hood has been installed properly.
Important Safety Information: Please Read this before installing & using. o o o o o Any installation work must be carried out by a qualified electrician or competent person. The hood must be installed in accordance with the installation instructions and all measurements followed. If the cooker hood is installed for use above a gas appliance then the provision for ventilation must be in accordance with the Gas Safety Codes of Practice BS.6172, BS.5440 & BS.6891 (Natural Gas) and BS.
o Safety Information: Please Read this before installing & using. Important o Ensure the ducting for the extractor function has the same diameter as the outlet hole all the way through. o Keep young children from using, playing with or tampering with the cooker hood. Older children and infirm persons should be supervised if they are using the cooker hood. ventilation measures are being observed. Note that it removes odours from your room, not steam.
Environmental Note Note: Before discarding an old appliance, switch off and disconnect it from the power supply. Cut off and render any plug useless. Cut the cable off directly behind the appliance to prevent misuse. This should be undertaken by a competent person. CONFORMITY TO W.E.E.E.
Using your Baumatic Cooker Hood: To use your cooker hood: 1) Make sure it has been properly installed. 2) Find the CONTROL PANEL. It is located at the front of the canopy, to the right. 3) The CONTROL PANEL contains buttons as shown in the Figure below. These perform separate functions. You will need to understand what these buttons do before you attempt to use your cooker hood. * Note: The hood should be switched on at least as soon as you start cooking.
Cleaning your Baumatic Cooker Hood: IMPORTANT: Before cleaning, always ensure that you have switched your cooker hood OFF at the omni-polar switch, set at the wall from the cable: Cleaning  Clean the external parts with mild liquid detergents on a damp cloth.  Never use abrasive powder, corrosive solvents or brushes.  Never insert pointed objects into the motor’s protective grid.   Be sure to replace the carbon filters at the recommended intervals. Build up could cause a fire hazard.
Maintenance - Cleaning the Anti-grease Filters First remove the grille by pulling down on it. Undo the side catches. You can now clean the anti-grease filter grilles. 9 Soak them for about one hour in hot water with a grease-loosening detergent then rinse off thoroughly with hot water. 9 Repeat the process if needed. Refit the grease grille once it has dried. 9 Refit the grease grilles when dry. 9 PLEASE NOTE: DISCOLOURATION OF THE GREASE FILTER CAN TAKE PLACE WHEN CLEANED IN A DISHWASHER, ETC.
Maintenance – Changing the Light Bulb and Carbon Filter a) Changing the light bulb 9 Before changing the light bulb, ensure that the appliance is not live (i.e., ensure that you have switched it off at the wall switch). 9 Remove the metal anti-grease filters (see Figure 2 below) and find the old bulb located in the light fixture up inside the exposed canopy. Change the halogen bulb using only olive-shaped spares with an E14 coupling, max. 40W.
Installing / Changing the Carbon Filter Installing / Changing the Carbon Filter. Your Baumatic Cooker Hood uses a pair of CARBON FILTERS to purify the air for the air recirculation function. You will find that the filters will attach to both sides of the fan motor (please see figures at bottom of page). The active carbon filters must be replaced regularly, at least once every three months, to allow normal operation. Before starting to fit the carbon filter, turn the omni-polar switch off at the wall.
INSTALLATION INSTRUCTIONS – Electrical Connection. Before installation and usage, read all the instructions and make sure that the voltage (V) and the frequency (Hz) indicated on the identification plate (found inside your Cooker Hood) and on the data inside the appliance are exactly the same as the voltage and frequency in your home.
INSTALLATION INSTRUCTIONS – Installing your Cooker Hood : The cooker hood must not PLEASE NOTE THAT YOU WILL HAVE TO DECIDE BEFORE INSTALLING YOUR COOKER HOOD THAT YOU CAN ADAPT IT AS AN EXTRACTION FAN. PLEASE SEE PAGE 18 NOW TO UNDERSTAND CRUCIAL DIFFERENCES IN THESE. be fitted above stoves with a radiant top plate. : We recommend that at least two people install this hood. NOTE: Your Baumatic Cooker Hood should only be fitted on a wall. Do NOT position it any less than 700 mm (70 cm) above the hob.
INSTALLATION INSTRUCTIONS – Attaching the Hood Rear view of your cooker hood. -------------------------------------------------------------------------3) Using a drill bit with a 6 mm diameter, make holes in the wall where you have marked these positions (see below).
INSTALLATION INSTRUCTIONS – Attaching the Hood ------------------------------------------------------------------------------------------- ------------------------------------------------------------------------------------------6) (EXTRACTION FUNCTION ONLY) Connect the coupling to the top of the cooker hood (see below). Then connect the discharge pipe to the coupling as shown below.
INSTALLATION INSTRUCTIONS – Fitting the Chimney FITTING THE PIPE – Once your Cooker Hood has been installed, you can now fit the pipe. 1) Take the two casings ‘A’ and ‘B’: 2) Rest the bottom of the casing ‘A’ on the top of the hood, taking care to position the tabs of the casing correctly on the back of the hood as shown as part ‘X’ in Figure 4 at right. 3) Fix casing ‘A’ onto the hood using the two screws ‘K’ supplied in the bag of accessories (Figure 4 – at right).
INSTALLATION INSTRUCTIONS – Fitting the Chimney 6) Take the fixing bracket ‘G’ (Fig. 4 – previous page), centre it with respect to the mark you previously made, keeping it in contact with the ceiling, and then mark the anchoring holes (‘H’). 7) Using a drill bit with a 6mm diameter, make two holes on the fixing marks you previously made (see below). 8) Insert the expansion fixings (rawlplugs) provided, put bracket ‘G’ (see Fig. 4 on previous page) in position and secure it with the screws provided.
ATTACHING THE GLASS Remove the metal grease filters from the hood Slacken both anchoring screws “F” Place the glass ‘Q’ on the upper shelf of the hood, pushing it in towards the wall. Tightening the screws ‘F’ again in the hole and connecting them to the unit. Take care that the anchoring corner is firmly fastened, tightening it well. Re-insert the ventilation tube with the coupling tube ‘N’. PLEASE NOTE * DO NOT OVERTIGHTEN THESE SCREWS OR YOU MAY DAMAGE / DISTORT THE UNIT.
Extraction / Air Purifier Modes of Operation EXTRACTION OPERATION – Installation Instructions  Ensure that you have fitted the union (‘N’) to the upper part of the hood using the packaged two screws supplied inside the packing (Fig. 1 – on right). Using a 125 mm diameter pipe, connect the union (N) on the upper part of the hood (see Fig. 1) to the discharge outlet for cooking vapours with a crosssection of at least 150 cm².
If your Cooker Hood comes with a Lower Bracket * Note on what to do if your Cooker Hood is the version that comes with a BRACKET. Please note that your cooker hood may include a lower bracket. If this is the case, you will need to have it installed as such. This will mean a slight change in how the cooker hood is to be installed from the process shown on page 13. In Fig. 6, below, you will see an exploded view of your cooker hood and (inset), the bracketed connecting area of the hood (‘N’).
Troubleshooting If something has gone wrong with your Cooker Hood, checking against this chart might keep you from having to call for service. Symptom The cooker hood will not start! The cooker hood is not working effectively! The cooker hood has switched off during operation! 21 Solution • Check that the hood is connected to the electricity supply. • Check that the fan speed control is set properly. • The fan speed is not set high enough. • The grease filter is dirty.
Baumatic Ltd. Conditions of guarantee Dear Customer, Your new Baumatic appliance comes complete with a free 12 month guarantee covering both parts and labour costs resulting from defective materials or workmanship. Baumatic also gives you the opportunity to automatically extend the guarantee period for a further 12 months at no extra cost, giving an initial guarantee period of 24 months. The extended guarantee period applies to England, Scotland, Wales and Northern Ireland only.
Headquarters Baumatic Ltd. Baumatic Buildings, 6 Bennet Road, Reading, Berkshire RG2 0QX, United Kingdom Sales Telephone +44 118 933 6900 Sales Fax +44 118 931 0035 Service Telephone +44 118 933 6911 Service Fax +44 118 986 9124 Spares Telephone +44 118 933 6922 Technical / Advice Telephone +44 118 933 6933 E-mail: sales@baumatic.co.uk technical@baumatic.co.uk Http (Internet site): www.baumatic.
24
