BU676GL-EU 60 cm Cooker hood BU976GL-EU 90 cm Cooker hood 1
User Manual for your Baumatic BU676GL-EU 60 cm Cooker hood in stainless steel and glass BU976GL-EU 90 cm Cooker hood in stainless steel and glass NOTE: This User Instruction Manual contains important information, including safety & installation points, which will enable you to get the most out of your appliance. Please keep it in a safe place so that it is easily available for future reference; for you or any person not familiar with the operation of the appliance.
Contents Page Environmental note 4 IMPORTANT SAFETY INFORMATION 5–7 Specifications of your cooker hood BU676GL-EU BU976GL-EU Optional extras (both models) 8–9 8 9 9 Using your Baumatic cooker hood Before first use To use your cooker hood Setting the time of day Setting the fan speed The cut off timer 10 - 12 10 10 11 11 – 12 12 Cleaning your Baumatic cooker hood The grease filter 13 13 Maintenance Removing and cleaning the grease filter Changing a light bulb Fitting the carbon filters 14 - 16 14
ENVIRONMENTAL NOTE Note: Before discarding an old appliance, switch off and disconnect it from the power supply. Cut off and render any plug useless. Cut the cable off directly behind the appliance to prevent misuse. This should be undertaken by a competent person. CONFORMITY TO W.E.E.E.
IMPORTANT SAFETY INFORMATION Your safety is of the utmost importance to Baumatic. Please make sure that you read this instruction booklet before attempting to install or use the appliance. If you are unsure of any of the information contained in this booklet, please contact the Baumatic Advice Line. IMPORTANT: Any installation work must be carried out by a qualified electrician or competent person. o The hood must be installed in accordance with the installation instructions and all measurements followed.
o The edges of the cooker hood are sharp – be mindful of this as you handle your appliance, especially during installation and cleaning. DO NOT CLEAN IN BEHIND THE GREASE FILTERS! o If the room where the cooker hood is to be used contains a fuel burning appliance such as a central heating boiler then its flue must be of the sealed or balanced flue type. o If other types of flue or appliances are fitted, ensure that there is an adequate supply of air in the room.
o Remember that when in extraction mode, your cooker hood is removing air from your room. Ensure that proper ventilation measures are being observed. o Note: Your cooker hood is designed to remove cooking odours from the room and not steam. o Warning - Always ensure that the cooker hood has been disconnected from the power supply before carrying out any work on the hood, including replacing light bulbs.
Specifications of your cooker hood BU676GL-EU PRODUCT DIMENSIONS: Height: Width: Depth: 540 mm 600 mm 327 mm Your stainless steel cooker hood is fitted with: o o o o o High extraction tangential motor Push button control operation 3 Speeds 1 Metallic grease filter 2 lights Extraction capacity: 750 m³/hr Noise level min/max: 54 – 64 dB MODEL NUMBER CARBON FILTER REQUIRED BU676GL-EU S1 8
BU976GL-EU PRODUCT DIMENSIONS: Height: Width: Depth: 540 mm 900 mm 327 mm Your stainless steel cooker hood is fitted with: o o o o o High extraction tangential motor Push button control operation 3 Speeds 1 Metallic grease filter 2 lights Extraction capacity: 750 m³/hr Noise level min/max: 54 – 64 dB MODEL NUMBER CARBON FILTER REQUIRED BU976GL-EU S1 Optional extras (both models) DK5 1 Metre length Ducting Kit 125 mm Ø. DK10 3 Metre length Ducting Kit 125 mm Ø with flat channelling included.
Using your Baumatic cooker hood Before first use IMPORTANT: THIS PROCESS MUST BE FOLLOWED BEFORE THE COOKER HOOD IS USED FOR THE FIRST TIME. o You should use a good quality stainless steel cleaner and polish on ALL of the stainless steel areas of your cooker hood, before it is used for the first time. o This will help to leave a silicone water-resistant film to protect the stainless steel surfaces.
Setting the time of day o After the appliance is connected to your mains supply, press the ON/OFF button to switch the hood on, the LED display backlight will switch on. If no other button is pushed within 30 seconds, then the backlight will go out. o Press and hold down the timer button for a few seconds, the hour section of the LED display will flash. o Press the speed selection button to increase the number shown on the LED display.
o To switch the fan off, press the ON/OFF button. o When you next switch on the cooker hood using the ON/OFF button, it will remember the operating speed that it was last used at. The cut off timer o Whilst the cooker hood is in use, if you press the timer button the number “12:00” will appear on the LED display. o This indicates that the hood will run for a further 12 minutes at the current fan speed. o Once the 12 minute period has elapsed, the cooker hood will switch itself off.
Cleaning your Baumatic cooker hood IMPORTANT: BEFORE CLEANING, ALWAYS ENSURE THAT YOU HAVE SWITCHED YOUR COOKER HOOD OFF AT THE OMNI-POLAR SWITCH, SET AT THE WALL FROM THE CABLE. Cleaning o Clean the external parts of your cooker hood with mild liquid detergent and a new damp cloth. o Never use abrasive powder, corrosive solvents or brushes. o Never insert pointed objects into the motor’s protective grid.
Maintenance Removing and cleaning the grease filter o Lift up the cover that sits over the grease filter (as shown in the line drawing above). o Remove the grease filter by pulling down on the handle and pulling it away from the cooker hood. o Soak the grease filter in hot water and washing up liquid for at least 5 minutes (or longer if the grease build up is severe). o Rinse it off thoroughly with hot water. o Repeat the process if required. o Refit the grease filter once it has dried.
o Close the cover that sits over the grease filter. o IMPORTANT: Let the grease filter dry thoroughly before refitting it in the cooker hood. Changing a light bulb IMPORTANT: BEFORE ATTEMPTING TO CHANGE A LIGHT BULB, YOU MUST ENSURE THAT YOU HAVE DISCONNECTED THE COOKER HOOD FROM YOUR MAINS SUPPLY. o Prior to touching the light bulbs ensure they are cooled down. o Find the bulb that requires replacement, you will find it located in the light fixture which is inside the exposed section of the canopy.
Fitting the carbon filters If the appliance is being used to be used in recirculation mode then it is necessary to fit carbon filters. This will help to absorb unpleasant odours caused by cooking. IMPORTANT: BEFORE ATTEMPTING TO FIT OR REMOVE THE CARBON FILTERS, YOU MUST ENSURE THAT YOU HAVE DISCONNECTED THE COOKER HOOD FROM YOUR MAINS SUPPLY. 1) Remove the grease filters. 2) Hook the carbon filter over the pins that are located at the end of the motor.
Installation IMPORTANT: Before installation and usage read all the instructions and make sure that the voltage (V) and the frequency (Hz) indicated on the rating plate are exactly the same as the voltage and frequency in your home. The rating plate can be found behind the grease filter.
o As the colours of the wires in the appliance’s mains lead may not correspond with the coloured markings identifying the terminals in your spur box, please proceed as follows: o The blue wire must be connected to the terminal marked “N” (neutral), or coloured black. o The brown wire must be connected to the terminal marked “L” (live), or coloured red. Before beginning installation o Check that the product purchased is of a suitable size for the chosen installation area.
o Do not tile, grout or silicone this appliance to the wall. This appliance is designed to be surface mounted only. Installing your cooker hood IMPORTANT: YOU WILL HAVE TO DECIDE BEFORE INSTALLING YOUR COOKER HOOD WHETHER TO USE IT IN EXTRACTION MODE OR RECIRCULATION MODE. PLEASE TURN TO PAGE 25 NOW TO UNDERSTAND THE DIFFERENCES BETWEEN THESE TWO MODES. o We recommend that at least two people install this hood.
2a) The support screw holes are indicated by figure A in this drawing and the anchoring screw holes are indicated by figure B. 3) Using a drill bit with an 8 mm diameter, make holes in the wall on the positions that you have marked in step 2. 4) Insert rawl plugs into all of the holes that you have drilled. 5) Fasten the support screws halfway in, leaving them 10 mm out of the wall.
6) Hang the hood onto the support screws. 7) Fully tighten the support screws (A) and then screw the anchoring screws (B) through the relevant holes in the cooker hood. Fully tighten the anchoring screws into the wall.
Connecting to external ducting 8) Connect the coupling to the top of the cooker hood, and then connect a 125 mm ducting hose to the coupling (please note that the ducting hose is not supplied with the appliance). o The other end of the ducting hose should be connected to a discharge outlet that is suitable for cooking vapours. It should have a cross section of at least 150 cm². o The maximum distance between the coupling and your discharge outlet should be 3 metres, with one 90 degree bend.
10) Lift chimney section (D) upwards until it reaches the ceiling. You must ensure that it is perpendicular to the hood. o Mark the side measurements of both sides of chimney section (D) on the wall with a pencil and then remove chimney section (D). 11) Take the flat bracket (E) and place it between the two pencil marks that you made in step 9 o Keeping the bracket in contact with the wall, use a pencil to mark on the wall the anchoring holes that are cut out of the bracket.
12) Using an 8 mm drill bit, drill out two holes on the pencil markings that you made in step 11. Insert rawl plugs into the holes and then use a screwdriver to secure the fixing bracket to the wall. o Refit chimney section (C) to the hood and fix it onto the hood using the two screws that are supplied. o Secure the top of chimney section (C) to the flat bracket, using the screws provided. o Slide chimney section (D) inside of chimney section (C).
Completing the installation If you are setting the appliance to recirculation mode, then you should now fit the two carbon filters. See the “Fitting the carbon filters” section on page 16. The electrical connection must correspond to the electrical requirement noted on the rating plate, which is placed inside the cooker hood. The appliance should now be connected to the electrical supply. See page 17 - 18 for detailed information on the electrical connection.
Troubleshooting IMPORTANT: If your cooker hood appears not to be operating properly, before contacting the Baumatic Customer Care Department, please refer to the checklist below. My cooker hood will not start. o Check that the hood is connected to the electricity supply o Check that the fan speed control is set correctly. My cooker hood is not working effectively. o The fan speed is not set high enough o The grease filters are dirty and require cleaning. o The kitchen is not well ventilated enough.
IMPORTANT: If your appliance appears not to be operating correctly, then you should disconnect it from your mains supply and then contact Baumatic Customer Care on telephone number (0118) 933 6911. DO NOT ATTEMPT TO REPAIR THE APPLIANCE YOURSELF. Please note that if an engineer is asked to attend whilst the product is under guarantee and finds that the problem is not the result of an appliance fault, then you may be liable for the cost of the call out charge.
Czech Republic Baumatic CR spol s.r.o. Průmyslová zóna Sever 696 460 11 Liberec 11 Czech Republic United Kingdom Baumatic Ltd., Baumatic Buildings, 6 Bennet Road, Reading, Berkshire RG2 0QX United Kingdom +420 483 577 200 www.baumatic.cz Slovakia Baumatic Slovakia, s.r.o.