MEGA10W Extra large 10 kg capacity washing machine MEGA10WD Extra large 10 kg capacity washer dryer 1
PARTS AND FEATURES WASHING MACHINE SAFETY INSTALLATION INSTRUCTIONS INLET HOSE CONNECTION ELECTRICAL REQUIREMENTS OPERATING YOUR WASHING MACHINE THE FUNCTIONS OF THE WASHING MACHINE CONTROL PANEL WASHING PROGRAMMES WASHING PROCEDURE AND SELECTION GUIDE FOR OTHER USEFUL PROGRAMS MAINTENANCE HOW TO CLEAN THE FILTER REMOVING STAINS TROUBLE SHOOTING CONDITIONS OF GUARANTEE SERVICE CONTACTS 2 3 4 5 7 8 10 12 13 24 28 29 30 31 32 33
ACCESSORIES Hose drain Inlet hose Spanner 2 Manual Blanking Cap (x4)
WASHING MACHINE SAFETY Save these instructions Your safety is important to us. To reduce the risk of fire, electrical shock, or injury when using your washing machine adhere to the following basic precautions. Read all instructions before using your washing machine Please ... • Have only a qualified person install, repair, or replace parts on washer. • Ensure your washing machine is regulary maintained and serviced.
INSTALLATION INSTRUCTIONS Removing transit bolts 1. Before operating the washer, remove the transit bolts (4 each) along with the rubber. 2. Unscrew the 4 bolts with the spanner supplied. Keep the 4 bolts and spanner for future use. • If the bolts are not removed, it may cause heavy vibration, noise and malfunction. • Whenever the appliance is transported, the transit bolts must be refitted. 3. Close the holes with the Blanking Caps supplied.
INLET HOSE CONNECTION The machine should be connected to the water mains using the new hose sets supplied. NEVER reuse old hoses. Be sure that the water inlet hoses are not folded, broken or crushed. The washer should be connected to the cold water supply as this gives the most efficient wash results.
WATER DRAIN CONNECTION x Be sure that the drain hoses are not folded, twisted, crushed or elongated by stretching. x Water drain hose should be mounted at a height of a minimum of 60 cm to a maximum of 100 cm from the ground. x The end of the water drain hose may be directly fitted to the waste water outlet connection or to a standalone pipe. The standpipe should have a diameter of approximately 38 mm (see diagram) ensuring there is an air break between the drain hose and standpipe.
ELECTRICAL REQUIREMENTS WARNING - Electrical shock hazard: Failure to follow these instructions could result in death or serious injury. - An electrical earth is required on this machine- If it does not fit the outlet; have a proper outlet installed by a qualified electrician. Don’t earth to a gas pipe. Don’t change the power supply cord plug. Check with a qualified electrician if you are not sure the machine is properly earthed.
2 Adjust the level of the washing machine using the adjustable legs. • Please check if there is any gap between the four adjustable legs and the floor. • Turn the adjustable legs using the enclosed spanner, adjust the level of the machine and make sure that it is stable. • Adjust the fixing nuts up tightly so that the adjustable leg machine maintains the adjustment. Fixing Nut 3 Make sure that the washing machine does not move when you press down the four corners of the washer's top plate.
Sorting • Separate heavily soiled items from lightly soiled ones, even if they would normally be washed together. • Separate dark colours from light colours, colourfast items from non-colourfast items. Soil (Heavy, Normal, Light): Colour (White, Lights, Darks): Lint (Lint producers, Collectors): Separate clothes according to amount of soil. Separate white clothes from coloured clothes. Wash lint producers and lint collectors separately.
THE FUNCTION OF CONTROL PANEL(MEGA10WD) Press this button to turn the power 'ON' or 'OFF'. Operation and temporary stop is repeated as it is pressed. When you want to change a programme while operating; Press the 'Start/Pause' button ᆌ Select the programme that you want to change ᆌ Press the 'Start/Pause' button again. You can select the programme you want and each lamp is turned on when that course is selected.
THE FUNCTION OF CONTROL PANEL(MEGA10W) Press this switch to turn the power 'ON' or 'OFF'. Operation and temporary stop is repeated as it is pressed. When you want to change the program operating; Press the 'Start/Pause' button ᆌ Select the program that you want to change ᆌ Press the 'Start/Pause' button again. You can select the course you want and each lamp is turned on when that course is selected. You can select the wash course you want and each lamp is turned on when that course is selected.
WASHING PROGRAMS Program Fabric type Normal Colourfast garments (shirts, night dresses, pyjamas,..) and lightly soiled white cottons(underwear,..) 40 °C (cold,30°C, 60°C) Wash: main wash Rinse: 3 Spin: 800 Temp.: 40°C Refer to rating label White First check whether laundry is machine washable, (white cotton, linen, towel and sheets..) 95 °C (fixed) Wash: main wash Rinse: 3 Spin: 800 Temp.
WASHING PROCEDURE AND SELECTION 1. NORMAL PROGRAMME Put the laundry into the Drum. Step 1 Step 2 Then close the Door. • In the detergent compartment, put the powder into the main wash and prewash sections (See Diagram - Page 9). • Softener should be poured into the middle section of the compartment and be below 'MAX' level. • Put the detergent into the pre wash room(I marking) only if you want to add prewash. • When you want to use bleach, put it into the main wash room (I I marking) with detergent.
2. WHITE PROGRAMME Put the laundry into the Drum. Step 1 Then close the Door. • Put the detergent into the main wash and prewash sections (See Diagram - Page 9). • Softener should be poured into the middle section of the compartment and be below 'MAX' level. • Put the detergent into the pre wash section only if you want to add prewash. • When you want to use bleach, put it into the main wash section with detergent. Step 2 Press the Power button.
3. ECO-WHITE PROGRAMME Put the laundry into the drum. Step 1 Then close the Door. • In the detergent compartment, put the powder into the main wash and prewash sections (See Diagram - Page 9). • Softener should be poured into the middle section of the compartment and be below 'MAX' level. • Put the detergent into the pre wash section only if you want to add prewash. • When you want to use bleach, put it into the main wash section with detergent. Step 2 Press the Power button.
4. SYNTHETIC PROGRAMME Put the laundry into the drum. Step 1 Then close the Door. • In the detergent compartment, put the powder into the main wash and prewash sections (See Diagram - Page 9). • Softener should be poured into the middle section of the compartment and be below 'MAX' level. • Put the detergent into the pre wash section only if you want to add prewash. • When you want to use bleach, put it into the main wash section with detergent. Step 2 Press the Power button.
5. HEAVY STRAIN PROGRAMME Put the laundry into the drum. Step 1 Then close the Door. • In the detergent compartment, put the powder into the main wash and prewash sections (See Diagram - Page 9). • Softener should be poured into the middle section of the compartment and be below 'MAX' level. • Put the detergent into the pre wash section only if you want to add prewash. • When you want to use bleach, put it into the main wash section with detergent. Step 2 Press the Power button.
6. WOOL PROGRAMME Put the laundry into the drum. Step 1 Then close the Door. • In the detergent compartment, put the powder into the main wash section (See Diagram - Page 9). • Softener should be poured into the middle section of the compartment and be below 'MAX' level. • When you want to use bleach, put it into the main wash section with detergent. Step 2 Press the Power button. • The LED shows only this signal: '- --' Step 3 Select the 'WOOL' programme using the programme selection dial.
7. DELICATE PROGRAMME Put the laundry into the drum. Step 1 Then close the Door. • In the detergent compartment, put the powder into the main wash section. (See Diagram - Page 9). • Softener should be poured into the middle section of the compartment and be below 'MAX' level. • When you want to use bleach, put it into the main wash section with detergent. Step 2 Press the Power button. • The LED shows this signal: '- --' Step 3 Select the 'DELICATE' programme using the programme selection dial.
8. BLANKET PROGRAMME Put the laundry into the drum. Step 1 Then close the Door. • In the detergent compartment put the powder into the main wash section (See Diagram - Page 9). • Softener should be below 'MAX' level. • When you want to use bleach, put it into the main wash room (I I marking) with detergent. Step 2 Press the Power button. • The LED shows this signal: '- --' Step 3 Select the 'BLANKET' programme using the programme selection dial.
9. RAPID PROGRAMME Put the laundry into the drum. Step 1 Then close the Door. • In the detergent compartment, put the powder into the main wash section (See Diagram - Page 9). • Softener should be poured into the middle section of the compartment and be below 'MAX' level. • When you want to use bleach, put it into the main wash section with detergent. Step 2 Press the Power button. • The LED shows this signal: '- --' Step 3 Select the 'RAPID' programme using the programme selection dial.
10. MEMORY PROGRAMME Put the laundry into the drum. Step 1 Then close the Door. • In the detergent compartment put the powder into the main wash and prewash sections (See Diagram - Page 9). • Softener should be poured into the middle section of the compartment and be below 'MAX' level. • Put the detergent into the pre wash room:(I marking) only if you want to add prewash. • When you want to use bleach, put it into the main wash section with detergent. Step 2 Press the Power button.
11. DRUM CLEANING PROGRAMME Put the laundry into the drum. Step 1 Step 2 Step 3 Then close the Door. • If you want to clean the Drum slightly, use this programme without bleach. • If you want to clean the Drum thoroughly, please use detergent only. Press the Power button. • The LED shows only this signal: '- --' Select the 'DRUM CLEANING' programme using the programme selection dial.
GUIDE FOR OTHER USEFUL PROGRAMMES * DELAY START (RESERVED WASHING) Put the laundry into the drum. Step 1 Then close the Door. • In the detergent compartment, put the powder into the main wash and prewash sections (See Diagram - Page 9). • Softener should be poured into the middle section of the compartment and be below 'MAX' level. • Put the detergent into the pre wash section only if you want to add prewash. • When you want to use bleach, put it into the main wash section with detergent.
* ONLY WASH Step 1 Put the laundry into the Drum and put the detergent and softener into the detergent compartment. Then close the Door. Step 2 Press the Power button. • The LED shows this signal: '- --' Step 3 Select the 'WASH CYCLE' you want by pressing the 'WASH' button. • The 'NORMAL' programme is selected automatically. Step 4 Press the 'Start/Pause' button. • The machine will start operating by locking the Door and supplying water.
* DRYER (MEGA10WD) Step 1 Put the laundry into the Drum and close the Door. Step 2 Press the Power button. • The LED shows this signal: '- --' Step 3 Select the 'DRY CONDITION' you want by pressing the 'DRY' button. As this button is pressed, the dry condition is selected by 'Cupboard' → 'Very' → 'Time(30, 1:00, 1:30)' → OFF → 'Low Temp' → 'Iron' → 'Cupboard' Step 4 Press the 'Start/Pause' button. • The machine will start operating by locking the Door. Note • Do not use detergent and softener.
* RINSE+SPIN (MEGA10W) Step 1 Put the laundry into the Drum and put softener into the detergent compartment. Then close the Door. • Softener should be poured into the middle section of the compartment and be below 'MAX' level. Step 2 Press the Power button. • The LED shows this signal: '- --' Step 3 Select the programme you want using the programme selection dial. • If you press 'RINSE+SPIN' button without selecting a programme, the 'NORMAL' programme is selected as the default programme.
MAINTENANCE Proper care of your washer can extend its life. This section explains how to care for your washer properly and safely. Cleaning your washer Exterior Interior Wipe up detergent, bleach, and other spills with a soft, damp cloth or sponge as they occur. Occasionally wipe the outside of the washer to keep it looking like new. Clean interior with 250ml of chlorine bleach mixed with 500ml of detergent. Run washer through a complete cycle. Repeat this process if necessary.
HOW TO CLEAN THE FILTER Cleaning the water inlet filter Clean the filter when water leaks from the water inlet Pull the power plug out before cleaning the filter. Turn off the water supply to the washer and separate the inlet hose. Pull the inlet filter out. Remove the dirt form the inlet filter with a brush.
REMOVING STAINS Stained, heavily-soiled, or greasy items may need to be prewashed or soaked for best results. Soaking helps remove protein-type stains like blood, milk or grass. Prewashing helps loosen soil before washing. PLEASE REFER TO CLOTHING CARE ADVICE ON MANFACTURERS LABEL. Stain removal rules • Use warm water for soaking or prewashing stained laundry. Hot water can set stains. • Most stains are easier to remove when they are fresh.
TROUBLE SHOOTING Most problems are easily solved if you understand the cause. Check the following list for problems before calling for service. If error mode such as IE, OE, UE are displayed on the control panelfirst open and close the door, and then press START/PAUSE button. PROBLEM CHECK POINT • The machine will not operate at all.
Baumatic Ltd. Conditions of guarantee Dear Customer, Your new Baumatic appliance comes complete with a free 12 month guarantee covering both parts and labour costs resulting from defective materials or workmanship. Baumatic also gives you the opportunity to automatically extend the guarantee period for a further 12 months at no extra cost, giving an initial guarantee period of 24 months. The extended guarantee period applies to England, Scotland, Wales and Northern Ireland only.
Headquarters Baumatic Ltd. Baumatic Buildings, 6 Bennet Road, Reading, Berkshire RG2 0QX, United Kingdom Sales Telephone +44 118 933 6900 Sales Fax +44 118 931 0035 Service Telephone +44 118 933 6911 Service Fax +44 118 986 9124 Spares Telephone +44 118 933 6922 Technical / Advice Telephone +44 118 933 6933 E-mail: sales@baumatic.co.uk technical@baumatic.co.uk Http (Internet site): www.baumatic.
Environmental note o The packaging materials that Baumatic uses are environmentally friendly and can be recycled. o Please discard all packaging material with due regard for the environment.
2
