OMBRA6SS/BL/W/R 75 cm Touch control gas hob 1 el
User Manual for your Baumatic OMBRA6SS/BL/W/R 75 cm touch control gas hob NOTE: This User Instruction Manual contains important information, including safety & installation points, which will enable you to get the most out of your appliance. Please keep it in a safe place so that it is easily available for future reference; for you or any person not familiar with the operation of the appliance.
Contents Environmental note 4 Important safety information 5–7 Specifications Product and aperture dimensions Product specifications Standard accessories Electrical details Gas details Control panel Gas hob surface layout 8 – 10 8 8 8 9 9 10 10 Using the gas hob Before first use Setting the time of day Switching the hob on Automatic ignition with flame failure device Switching off a cooking zone Residual heat indicator Setting the burner shutoff time Releasing a blocked burner Safety lock Deactivating
Environmental note o The packaging materials that Baumatic uses are environmentally friendly and can be recycled. o Please discard all packaging material with due regard for the environment.
Important safety information Your safety is of the utmost importance to Baumatic. Please make sure that you read this instruction booklet before attempting to install or use the appliance. If you are unsure of any of the information contained in this booklet, please contact the Baumatic Customer Care Department. General Information o This appliance is designed for domestic household use and for the cooking and frying of domestic foodstuffs.
Child Safety o Baumatic strongly recommend that babies and young children are prevented from being near to the appliance and not allowed to touch the appliance at any time. During and after use, all surfaces will be hot. o If it is necessary for younger family members to be in the kitchen, please ensure that they are kept under close supervision at all times. o Older children should only be allowed to utilise the appliance when supervised.
Cleaning o Cleaning of the hob should be carried out on a regular basis. o IMPORTANT: Before attempting to clean the appliance, it should be disconnected from the mains and cool. o Great care should be taken whilst using this appliance and when following the cleaning procedure. o You should not use a steam jet or any other high pressure cleaning equipment to clean the appliance.
Specifications Product dimensions: Aperture dimensions: Depth: Width: Height: Depth: Width: 500 mm 740 mm 50 mm 480 mm 560 mm Product specifications: o o o o o o o o o o o 1 x 3.80 kW triple crown (wok) burner 1 x 3.00 kW rapid burner 2 x 1.75 kW semi-rapid burner 1 x 1.
Electrical details Rated Voltage: Supply Connection: Max Rated Inputs: Mains Supply Lead: 220 – 240 Vac 50 - 60 Hz 3 A (double pole switched fused outlet with 3mm contact gap) 0.006 3 core x 0.75mm² (Type RR-F marked) Gas details Connection: Type: Rp ½ (ISO R7) Natural Gas (20.9 mbar) Alternative LPG G30 (28-30 mbar) For future reference please record the following information which can be found on the rating plate and the date of purchase which can be found on your sales invoice.
Control panel 1) ON / OFF button 2) Safety lock button 3) Timer minus button 4) Timer plus button 5) Timer and clock selection button 6) Timer / clock display 7) Cooking zone display 8) Gas control plus button 9) Gas control minus button 10) Cooking zone position indicator 11) Cooking zone timer selection / cooking zone position LED 12) Safety lock activation LED Gas hob surface layout A) 3.80 kW triple crown (wok burner) B) 3.00 kW rapid burner C) 1.75 kW semi-rapid burner D) 1.
Using the gas hob Before first use IMPORTANT: You should clean the hob surface (see “Cleaning and maintenance” section). Setting the time of day Each time the power supply is cut off, the time displayed by the hob clock must be reset. o After initially powering the hob, the number 0.00 will appear on the timer display (6) with a flashing decimal point. o In this mode, the hob is in stand-by and can only be switched on by pressing the ON / OFF button (1).
Switching the hob on o The hob can be switched on by pressing the ON / OFF button (1) and holding it down for at least two seconds. o Once activated, the five displays related to the burners will show level 0, which indicates that the cooking zones are off. o If additional operations are not performed after the hob is switched on, it will automatically switch off after one minute.
o To obtain a continuous variation of the power level simply hold down the plus or minus button of the selected cooking zone and release it once the display shows the desired level. You can choose between 1 – 7 levels. o By selecting level 0, you will switch the burner off. Switching off a cooking zone o To switch off a cooking zone press and hold the relevant plus and minus buttons simultaneously for a moment.
Setting the burner shutoff time o With the timer function (5) a maximum time can be set after which a burner will switch off. o Each burner can be timed independently of the others and can be set either when the cooking zone is on or off. o The countdown will start immediately after the set time is confirmed. If no burner is being timed the hob will switch off automatically after 4 hours. Before setting a timer function, please light any burners that you wish to link to the timer.
o It is possible to return to the timer programming mode at any time to view the time remaining until it will shut off or to change the current settings, simply by pressing the timer button (5) and using the control buttons to select the desired burner. You can then follow the same procedure as outlined above. o If in programming mode no button is pressed for more than ten seconds, the setting procedure will be stopped automatically and the main display will return.
Safety lock o This function makes it possible to lock the keypad to protect it from accidental actions. It is activated by pressing the safety lock button (2) for at least two seconds. o Once activated, a decimal point will show on the power level display of each burner. o When the keypad is locked, the burner power levels and the timer settings cannot be changed. The only action permitted is to turn off the hob by pressing the ON / OFF button (1).
Energy saving tips o In the interests of saving energy, always use a pan within the minimum diameter and maximum diameter as indicated in the table below: Burner 1.00 kW Auxiliary 1.75 kW Semi-rapid 3.80 kW Triple crown Maximum Minimum Ø Ø 60 mm 140 mm (with reducer) 160 mm 200 mm 240 mm o The diameter of the bottom of the pan should correspond to that of the burner. o The burner flame must never extend beyond the diametre of the pan. o Use flat bottomed pans only.
Cleaning Cleaning operations must only be carried out when the hob is cool. The appliance should be disconnected from your mains supply before commencing any cleaning process. Cleaning the hob top Any residues that are left on the hob top surface from cleaning agents will damage it. You should remove any residues with warm soapy water. Abrasive cleaners or sharp objects will damage the hob surface; you should clean it using warm soapy water.
o After cleaning and washing them, wipe and dry them carefully. o Before placing the burners back on the hob top, make sure that the gas jet is not blocked. o IMPORTANT: Make sure that you reassemble the burners in the original way. Maintaining the cast iron pan stands o IMPORTANT: Make sure that the hob surface and pan stands have cooled before you attempt to touch them. o Wipe the pan stands over with a soft, damp cloth that has been put into warm soapy water.
Installation The installation must be carried out by a GASSAFE registered installer, in accordance with the current version of the following.
If the underside of the horizontal surface is lower than 400 mm, then it must be at least 50 mm away from the outer edges of the hob. o 50 mm clearance around the appliance and between the hob surface and any combustible materials.
Installing the appliance o If the hob is installed without an oven below it, place a separating panel made from an appropriate material at a minimum distance of 10 mm below it. o If the hob is installed over an oven, place a separating panel at a minimum distance of 15 mm below it and follow the manufacturer’s instructions of the oven. F = 10 mm (min) H = 50 mm (min) G = 15 mm (min) C = 30 mm (min) D = 120 cm² E = 180 cm² Always allow sufficient ventilation.
o Cut a hole in the worktop that corresponds with the diagram below: o Carefully turn the hob upside down and place it on a cushioned mat. o Apply the sealing strip (A) provided around the edge of the appliance. o The protective covering must be removed from both sides. o Do not leave a gap in the sealing agent or overlap the thickness.
o IMPORTANT: Do not use a silicon sealant to seal the appliance against the aperture. This will make it difficult to remove the hob from the aperture in future if it needs to be serviced. (A) (B) (C) Sealing strip Clamp Screw o Place the clamp (B) over the holes that match the size of the screws. There are one set of screw holes in each corner of the hob. Slightly tighten a screw (C) through the clamp (B) so that the clamp is attached to the hob, but so that you can still adjust the position of it.
o The hob must be installed by a qualified person, in accordance with the current edition of the Gas Safety (Installation and Use) (Amendment) Regulations and the relevant building/I.E.E. Regulations. o Failure to install the appliance correctly could invalidate Baumatic’s guarantee and lead to prosecution under the regulations quoted above. o In the UK, GASSAFE registered installers are authorised to undertake the installation and service work, in compliance with the above regulations.
o Remember that the quantity of air necessary for combustion must never be less than 2m³/h for each kW of power (see total power in kW on the appliance rating plate). Gas Safety (Installation and Use) Regulations IMPORTANT: The appliance MUST be connected to the gas supply by use of a ½” BSP Elbow, seal, copper pipe and an isolation tap fitted in an easily accessible position.
Gas adjustment (Conversion to LPG) All work must be registered engineer. carried out by a GASSAFE IMPORTANT: Always isolate the hob from the electricity supply before changing the injectors and/or adjusting the minimum flow of the burners. o Remove the pan-stands, burners and flame spreaders (A). o Unscrew the injector (B) and replace it with the stipulated injector for the new gas supply (see table below).
o IMPORTANT: The minimum flow adjustment process must be completed before the appliance is next used. o To activate the procedure for selecting the combustible gas used, turn on the hob but keep the burners off. o Press the minus button for burner 1, minus button for burner 2 and the minus button for the timer all at the same time for at least two seconds.
o During the regulation procedure, the power level display will indicate if the set minimum corresponds to the factory setting, otherwise a flashing value or will be displayed if the gas flow rate is higher or lower than the presetting. o To confirm the desired minimum flow rate, press the timer button.
Electrical connection This appliance must be installed by a qualified person in accordance with the latest edition of the I.E.E. Regulations and in compliance with Baumatic’s instructions. Before connecting the appliance, make sure that the supply voltage marked on the rating plate corresponds with your mains supply voltage. o Cable type: H05 RRF 3 core x 0.75 mm² (Type RR-F marked). o The mains supply cable is supplied with this product.
My appliance isn’t working correctly Error codes o The burners will be shut down when the hob has tried three consecutive times to ignite the burner without success. Solution: Execute the following key sequence for release: o The burner can be released by pressing the relevant minus button and the safety lock button (2) simultaneously for at least two seconds. o When released, the burner will be restored to level 0 and is ready to be reignited.
o The burner was shut down more than five times in fifteen minutes or the release procedure was repeated for five consecutive times during a fifteen minute period. Solution: Wait fifteen minutes before carrying out the key release sequence: o The burner can be released by pressing the relevant minus button and the safety lock button (2) simultaneously for at least two seconds. o When released, the burner will be restored to level 0 and is ready to be reignited.
o The burner can be released by pressing the relevant minus button and the safety lock button (2) simultaneously for at least two seconds. o When released, the burner will be restored to level 0 and is ready to be reignited o If any of these error codes appear on the display, they cannot be reset with a command sequence. Solution: Contact the Baumatic Customer Care Department.
United Kingdom Baumatic Ltd., Baumatic Buildings, 6 Bennet Road, Reading, Berkshire RG2 0QX United Kingdom Sales Telephone (0118) 933 6900 Sales Fax (0118) 931 0035 Customer Care Telephone (0118) 933 6911 Customer Care Fax (0118) 986 9124 Spares Telephone (01235) 437244 Advice Line Telephone (0118) 933 6933 E-mail: sales@baumatic.co.uk customercare@baumatic.co.uk spares@baumatic.co.uk technical@baumatic.co.uk Website: www.baumatic.co.
