PHC620SS 60 cm/ PHC622SS 60 cm/ PHC720SS 77 cm Front touch control ceramic hob
User Manual for your Baumatic PHC620SS 60 cm PHC622SS 60 cm PHC720SS 77 cm Front touch control 4 hyperspeed zone ceramic hob. NOTE: This User Instruction Manual contains important information, including safety & installation points, which will enable you to get the most out of your appliance. Please keep it in a safe place so that it is easily available for future reference; for you or any person not familiar with the operation of the appliance.
Contents Environmental note 4 Important safety information 5–8 Specifications Ceramic hob surface layout Control panel layout Cooking zone indicators and neon’s 8 – 14 11 - 12 13 14 Using the ceramic hob Before first use Touch controls Turning the hob on Turning on a zone and setting a power level Turning off a zone gradually Turning off a zone instantly Turning the hob off Turning on a dual circuit zone Turning off a dual circuit’s outer section Residual heat indicator Locking the hob top Safety cut-
Environmental note o The packaging materials that Baumatic uses are environmentally friendly and can be recycled. o Please discard all packaging material with due regard for the environment.
Important safety information Your safety is of the utmost importance to Baumatic. Please make sure that you read this instruction booklet before attempting to install or use the appliance. If you are unsure of any of the information contained in this booklet, please contact the Baumatic Advice Line. General Information o This appliance is designed for domestic household use and for the cooking and frying of domestic foodstuffs.
Child Safety o Baumatic strongly recommend that babies and young children are prevented from being near to the appliance and not allowed to touch the appliance at any time. During and after use, all surfaces will become hot. o If it is necessary for younger family members to be in the kitchen, please ensure that they are kept under close supervision at all times. o Older children should only be allowed to utilise the appliance when supervised.
Cleaning o Cleaning of the hob should be carried out on a regular basis. o IMPORTANT: Before attempting to clean the appliance, it should be disconnected from the mains and allowed to cool. o Great care should be taken whilst using this appliance and when following the cleaning procedure. o You should not use a steam jet or any other high pressure cleaning equipment to clean the appliance.
o Pans should be lifted on and off the hob surface and not dragged. o Cooking zones should not be switched on without cookware placed on it. Also the cookware should not be empty. Specifications PHC620SS Product dimensions Height: Width: Depth: 40 mm 580 mm 510 mm Aperture dimensions Depth: Width: 495 mm 565 mm Product specifications: o o o o o o o o 1 x 0.75/2.20 kW double hyperspeed zone (Ø 120/210 mm) 1 x 1.10/2.00 kW oval hyperspeed zone (Ø 170/265 mm) 2 x 1.
PHC622SS Product dimensions Height: Width: Depth: 40 mm 580 mm 510 mm Aperture dimensions Width: Depth: 565 mm 495 mm Product specifications o o o o o o o o 1 x 0.75/2.20 kW double hyperspeed zone (Ø 140/210 mm) 1 x 1.10/2.00 kW oval hyperspeed zone (Ø 140/240 mm) 2 x 1.
PHC720SS Product dimensions Height: Width: Depth: 40 mm 770 mm 510 mm Aperture dimensions Depth: Width: 490 mm 750 mm Product specifications o o o o o o o o o 1 x 0.75/2.20 kW double hyperspeed zone (Ø 120/210 mm) 1 x 1.10/2.00 kW hyperspeed rectangular zone (Ø 140/240 mm) 1 x 1.80 kW hyperspeed zone (Ø 180 mm) 1 x 1.
For future reference please record the following information which can be found on the rating plate and the date of purchase which can be found on your sales invoice. The rating plate of your hob is located on the underneath of the appliance. Therefore it is a good idea to record this information before you install your appliance. Model Number ………………………………. Serial Number ………………………………. Date of Purchase ……………………………….
PHC622SS A B C D = = = = 1.20 kW hyperspeed zone (Ø 140 mm) 1.10/2.00 kW oval hyperspeed zone (Ø 140/240 mm) 0.75/2.
Control panel layout PHC620SS/ PHC622SS PHC720SS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13.
Cooking zone indicators and neon’s PHC620SS/ PHC622SS PHC720SS Using the ceramic hob Before first use IMPORTANT: You should clean the ceramic hob surface (see “Cleaning and maintenance” section). o You should switch on one cooking zone at a time, for 5 minutes at the maximum setting. This will help to eliminate any new smell that exists and evaporate any humidity that has formed on the heating elements during transit. o Do not burn off more than one zone at once.
Touch controls o All operations are performed by means of the touch controls that can be found on the control panel. o Each touch control has a visual display that corresponds to it. o Every time you press a touch control, an acoustic signal will sound. Turning the hob on o Press the ON/OFF button (1) o The cooking zone indicators (6) will all read “0”. o The decimal point symbols (7) will flash on and off.
Turning off a zone gradually o Press the minus button (5) until the number in the cooking zone indicator (6) reaches “0”. After 3 seconds, the zone will switch off automatically. o An “H” will show in the cooking zone indicator (6) until the temperature of the zone falls below 60°C (see the section on the “residual heat indicator” for further information). Turning off a zone instantly o Press the minus button (5) and the plus button (4) simultaneously. o The zone will switch off immediately.
Turning on a dual circuit zone The dual circuit zones have two cooking areas that you can use, a central section and an outer section. You can use the central section (A) independently or both sections (B) at once. o Use the plus (4) or minus (5) buttons of the dual circuit zone that you wish to use and select a power level between 1 and 9. o The central section of the duel circuit zone will switch on.
o When the temperature falls below 60°C, then the letter “H” and “0” will stop alternating (if the hob is still switched on), or the “H” will go out (if the hob is not switched on). o IMPORTANT: The residual heat indicator will disappear if your mains supply is cut. Locking the hob top o The whole hob top can be locked by pressing the safety lock button (2) whilst the appliance is turned on. o The safety lock neon (3) will light to show that the safety lock feature has been switched on.
o If the safety cut off has activated, the symbol “H” will appear in the cooking zone indicator (6) that applies to the cooking zone that has been left on. To reset the appliance, you should press the ON/OFF button (1). o If the plus (4) or minus (5) buttons are pressed, then the length of time before the safety cut-out will activate is reset.
o The period of time that a zone will automatically pre-heat for before dropping to the actual power level, is shown in the table below:LEVEL 1 2 3 4 5 6 7 8 9 TIME LIMIT 1 minute 11 seconds 2 minutes 44 seconds 4 minutes 47 seconds 5 minutes 28 seconds 6 minutes 29 seconds 1 minutes 11 seconds 2 minutes 44 seconds 2 minutes 44 seconds N/A Increasing the power level during automatic pre-heating o If a zone is already within automatic preheating mode and you wish to adjust the power level.
The hob timer o Touch either the plus (10) or minus (11) buttons of the timer. The timer display (12) will show “00” and a “t” symbol will appear on all of the cooking zone indicators. o After selecting the timer, a zone must be selected within 10 seconds by pressing one of the plus (4) or minus (5) buttons. You should use these buttons to select your desired power level. o The zone will switch on and start to heat, the timer neon (13) will switch on next to the relevant cooking zone indicator (6).
o IMPORTANT: If you cancel the timer setting, the selected zone will still remain on, therefore you will need to turn the zone off manually. Hob guidelines o The first few times the hob top is used, it may give off an acrid, burning smell. This smell will disappear completely with repeated use. o The hob surface is fitted with cooking areas of different diametre and power. o The positions where the heat will radiate from are clearly marked on the hob top.
o IMPORTANT: The ceramic hob surface is tough; however it is not unbreakable and can be damaged. Especially if pointed or hard objects are allowed to fall on it with some force. o DO NOT USE THE HOB IF THE SURFACE BECOMES BROKEN OR CRACKED. YOU SHOULD CONTACT THE BAUMATIC CUSTOMER CARE DEPARTMENT IMMEDIATELY. Cleaning and maintenance Cleaning operations must only be carried out when the hob is cool. The appliance should be disconnected from your mains supply before commencing any cleaning process.
Cleaning table Type of deposit Remove immediately? What should I use to remove the deposit? Yes Remove when the appliance has cooled down? No Sugar or food/liquid containing sugar Tin foil or plastic Yes No Fat splashes No Yes Metallic discolourations Water splashes or water rings No Yes No Yes Ceramic hob scraper Ceramic hob cleaner Ceramic hob cleaner Ceramic hob cleaner Ceramic hob scraper Using a ceramic hob scraper Your appliance will be provided with a hob scraper.
Using a specialist ceramic hob cleaner It is possible to purchase a specialist ceramic hob cleaner/conditioner. You should follow the instructions given by the manufacturer of the specialist ceramic hob cleaner. You should ensure that it is suitable for use on your appliance. Installation The installation must be carried out by a suitably qualified person, in accordance with the current version of the following. o UK Regulations and Safety Standards or their European Norm Replacements.
Unpacking the appliance When unpacking the appliance please check that the following items are contained within the packaging: 1 1 1 1 4 4 4 1 Baumatic hob Ceramic hob scraper Installation and instruction manual Baumatic guarantee card Fixing brackets Fixing screws Spring clips Sealing strip Installing the appliance PHC620SS PHC720SS PHC622SS Cut a hole in the worktop that corresponds with the drawings shown above.
o IMPORTANT: You must have a gap of at least 25 mm between the underneath of the appliance and any surface that is below it. o Carefully turn the hob upside down and place it on a cushioned mat. o Apply the sealing strip provided around the edge of the appliance. o The protective covering must be removed from both sides. o Do not leave a gap in the sealing agent or overlap the thickness. o IMPORTANT: Do not use a silicon sealant to seal the appliance against the aperture.
o Place the fixing brackets (B) over each hole and clip, and then place a screw (C) through the hole and fixing bracket (B). Tighten the screws a little way, so that they stay in place. IMPORTANT: Do not tighten the screws fully. o Carefully turn the hob back over and then gently lower it into the aperture hole that you have cut out. o On the underneath of the hob, locate the fixing brackets (B) and turn them so that they locate on the underneath of the worktop and the hob.
Connecting the mains supply cable o The mains terminal block is located on the underside of the hob and the terminals are accessible by removing the terminal block cover by removing the cover screw. o The cable connections must be in accordance with the diagram located on the bottom of the hob. o 1, 2 and 3 are the live connection, 4 and 5 are the neutral connection and the remaining one is the earth connection. o The live wire MUST be placed in connection number 1.
o The cable can be looped if necessary, but make sure that is not kinked or trapped when the hob is in position. Care must be taken to avoid the cable being in contact with hot parts of the appliance. Replacing the mains supply cable If the mains supply cable is damaged, then it must be replaced by an appropriate replacement. The mains supply cable should be replaced in accordance with the following instructions: o Switch the appliance off at the control switch.
* Check that the mains electrical supply to the appliance is correct and working. Check the mains fuse. o The residual heat indicator has not come on after I have switched a cooking zone off. * The cooking zone has only been turned on for a short period of time; therefore it did not go above 60°C. * IMPORTANT: If the cooking zone does appear to be hotter than 60°C and the residual heat indicator has not come on, you should call the Baumatic Customer Care Department.
IMPORTANT: If your appliance appears not to be operating correctly, then you should disconnect it from your mains supply and then contact the Customer Care Department on telephone number (0118) 933 6911. DO NOT ATTEMPT TO REPAIR THE APPLIANCE YOURSELF. Please note that if an engineer is asked to attend whilst the product is under guarantee and finds that the problem is not the result of an appliance fault, then you may be liable for the cost of the call out charge.
United Kingdom Baumatic Ltd., Baumatic Buildings, 6 Bennet Road, Reading, Berkshire RG2 0QX United Kingdom Czech Republic Baumatic CR spol s.r.o. Průmyslová zóna Sever 696 460 11 Liberec 11 Czech Republic Sales Telephone (0118) 933 6900 Sales Fax (0118) 931 0035 Customer Care Telephone (0118) 933 6911 Customer Care Fax (0118) 986 9124 Spares Telephone (01235) 437244 Advice Line Telephone (0118) 933 6933 www.baumatic.cz E-mail: sales@baumatic.co.uk customercare@baumatic.co.uk spares@baumatic.co.
