TEL06SS / TEL07SS Cooker hood
User Manual for your Baumatic TEL06SS / TEL07SS Cooker Hood NOTE: This User Instruction Manual contains important information, including safety & installation points, which will enable you to get the most out of your appliance. Please keep it in a safe place so that it is easily available for future reference; for you or any person not familiar with the operation of the appliance.
Contents Page Environmental note 4 IMPORTANT SAFETY INFORMATION 5–7 Specifications of your cooker hood TEL06SS TEL07SS 8–9 8 9 Using your Baumatic cooker hood Before first use To use your cooker hood 10 - 11 10 10 - 11 Cleaning your Baumatic cooker hood The grease filter 12 – 13 12 - 13 Maintenance Removing and cleaning the grease filters Changing a light bulb Fitting the carbon filters 13 – 15 13 14 14 - 15 Installation Electrical connection Before beginning installation Installing your cooker
ENVIRONMENTAL NOTE Note: Before discarding an old appliance, switch off and disconnect it from the power supply. Cut off and render any plug useless. Cut the cable off directly behind the appliance to prevent misuse. This should be undertaken by a competent person. o The packaging materials that Baumatic uses are environmentally friendly and can be recycled. o Please discard all packaging material with due regard for the environment.
IMPORTANT SAFETY INFORMATION Your safety is of the utmost importance to Baumatic. Please make sure that you read this instruction booklet before attempting to install or use the appliance. If you are unsure of any of the information contained in this booklet, please contact the Baumatic Advice Line. IMPORTANT: Any installation work must be carried out by a qualified electrician or competent person. o The hood must be installed in accordance with the installation instructions and all measurements followed.
o The edges of the cooker hood are sharp – be mindful of this as you handle your appliance, especially during installation and cleaning. DO NOT CLEAN IN BEHIND THE GREASE FILTERS! o If the room where the cooker hood is to be used contains a fuel burning appliance such as a central heating boiler then its flue must be of the sealed or balanced flue type. o If other types of flue or appliances are fitted, ensure that there is an adequate supply of air in the room.
o Remember that when in extraction mode, your cooker hood is removing air from your room. Ensure that proper ventilation measures are being observed. o Note that it removes odours from your room, not steam. o Warning - Always ensure that the cooker hood has been disconnected from the power supply before carrying out any work on the hood, including replacing light bulbs. o Do not connect the ducting system of this appliance to any existing ventilation system which is being used for any other purpose.
Specifications of your cooker hood TEL06SS PRODUCT DIMENSIONS APERTURE DIMENSIONS Height: Width: Depth: Width: 600 mm Depth: 194 mm (min) 175 600 306 450 mm mm mm (encased) mm (extended) Your cooker hood is fitted with: o o o o Slider control operation 3 x speeds 2 x metallic grease filters 2 x light Extraction capacity: 440 m³/hr Optional extras: 1 x Pair of recirculation ST1 Carbon filters for air 8
TEL07SS PRODUCT DIMENSIONS APERTURE DIMENSIONS Height: Width: Depth: Width: Depth: 270 600 306 450 mm mm mm (encased) mm (extended) 600 mm 280 mm MIN Your cooker hood is fitted with: o o o o Electronic control operation 3 x speeds 2 x washable aluminium grease filters 2 x light Extraction capacity: 750 m³/hr Optional extras: 1 x Pair of recirculation ST1 Carbon filters for air All of the optional extras are available from the Baumatic Spares Department.
Using your Baumatic cooker hood Before first use IMPORTANT: THIS PROCESS MUST BE FOLLOWED BEFORE THE COOKER HOOD IS USED FOR THE FIRST TIME. o You should use a good quality stainless steel cleaner on ALL of the stainless steel areas of your cooker hood, before it is used for the first time. o This will help to leave a silicone water-resistant film to protect the stainless steel surfaces.
Light ON / OFF switch. This switch turns your cooker hood’s light on and off. Slide the switch to position 1 to turn the light on and position 0 to turn it back off. IMPORTANT: IDEALLY YOU SHOULD SWITCH ON YOUR HOOD TEN MINUTES BEFORE YOU START TO COOK, OR AT THE VERY LEAST WHEN YOU BEGIN COOKING. YOU SHOULD ALSO RUN YOUR HOOD FOR TEN MINUTES AFTER YOU HAVE FINISHED COOKING. TEL07SS o The control panel contains buttons as shown in the image below, which perform separate functions.
Cleaning your cooker hood IMPORTANT: BEFORE CLEANING, ALWAYS ENSURE THAT YOU HAVE SWITCHED YOUR COOKER HOOD OFF AT THE OMNI-POLAR SWITCH, SET AT THE WALL FROM THE CABLE. Cleaning o Clean the external parts of your cooker hood with mild liquid detergent and a new damp cloth. o Never use abrasive powder, corrosive solvents or brushes. o Never insert pointed objects into the motor’s protective grid.
Maintenance Removing and cleaning the metal filter o First remove the grease filter by pulling down on the handle and pulling it away from the cooker hood. o Soak the metal filters in hot water and washing up liquid for about an hour. o Rinse them off thoroughly with hot water. o Repeat the process if required. o Refit the metal filters to the cooker hood once they have dried. o IMPORTANT: Let the grease filters dry thoroughly before refitting in the cooker hood.
Changing a light bulb IMPORTANT: BEFORE ATTEMPTING TO CHANGE A LIGHT BULB, YOU MUST ENSURE THAT YOU HAVE DISCONNECTED THE COOKER HOOD FROM YOUR MAINS SUPPLY. o Remove the metal filters by pulling down on the handle and pulling them away from the cooker hood. This will allow you access to the lamp area. o Prior to touching the light bulb ensure that it has cooled down. o Replace the bulb using only olive-shaped spares with an E14 coupling, max. 40W. Replace the grease filter support grilles.
2) Hook the carbon filter over the pins that are located at the end of the motor. 3) Turn the carbon filter clockwise until you feel it latch onto the motor’s sides. 4) Replace the grease filters. o When replacing the carbon filter, follow the steps outlined above and turn the carbon filter anti-clockwise to unlatch it from the motor.
Electrical connection YOUR COOKER HOOD IS INTENDED FOR FITTED AND PERMANENT INSTALLATION. o If not supplied the power cable must be connected to the terminals marked L (live) and N (neutral) in the hood and fixed with a cable clamp. o The cooker hood’s power cable must be fitted upstream from the electrical connection, using an omni-polar switch with a contact distance of at least 3 mm. WARNING: THIS APPLIANCE MUST NOT BE EARTHED.
then there should also be space to connect a ducting hose to the outside. o Carry out all necessary masonry work prior to the fitting of the cooker hood. o Ensure that all electrical connections are carried out by a suitably qualified person. o Before commencing installation of the cooker hood the grease filters should be removed. o Check inside the product and ensure that there is no transit packaging or any other materials, such as packets of screws, guarantees etc.
IMPORTANT: YOUR COOKER HOOD SHOULD BE CONNECTED TO YOUR MAINS SUPPLY AFTER THE REST OF THE INSTALLATION PROCESS HAS BEEN COMPLETED. Wall installation NOTE: All the screws mentioned in this section come with your cooker hood. 1) Position the hood against the wall and mark the positions of 4 holes of 8 mm diameter on a suitable place and according to the centre distance of the hole on the back of the cooker hood. 2) Drill these holes into the wall.
Installation into the underside of a kitchen cabinet 1) Drill holes of 4 mm diameter on the bottom of the cupboard you wish to hang the hood from in accordance with the diagram below: 2) Put the one way valve on the cooker hood and then install the hood on the bottom of the cupboard. Fasten the hood securely in place by tightening the screws. 3) Install the adjusted board on the bottom of the hood in order to keep out the gap between the hood back and the cupboard.
Connecting to external ducting o Connect the coupling to the top of the cooker hood, using two of the smaller screws provided. o Connect a 150 mm ducting hose to a discharge outlet that is suitable for cooking vapours. If you need to fit a 125 mm ducting hose, then a reducer is supplied with the appliance to allow you to do this.
correctly by selecting each speed and switching the light bulb on and off. Extraction mode or recirculation mode? IMPORTANT: YOU WILL HAVE TO DECIDE BEFORE INSTALLING YOUR COOKER HOOD WHETHER TO USE IT IN EXTRACTION MODE OR RECIRCULATION MODE. What is the difference between extraction and recirculation modes? In extraction mode, the stale air will be taken via the grease filter and out of the room via external ducting.
Troubleshooting IMPORTANT: If your cooker hood appears not to be operating properly, before contacting the Customer Care Department, please refer to the checklist below. My cooker hood will not start. o Check that the hood is connected to the power supply and whether you have selected any of the fan speeds. My cooker hood is not working effectively. o Check that fan speed is set to an appropriate setting. o Check that the grease filters are not dirty and if they require cleaning.
My appliance isn’t working correctly IMPORTANT: If your appliance appears not to be operating correctly, then you should disconnect it from your mains supply and then contact Baumatic Customer Care on telephone number (0118) 933 6911. DO NOT ATTEMPT TO REPAIR THE APPLIANCE YOURSELF. Please note that if an engineer is asked to attend whilst the product is under guarantee and finds that the problem is not the result of an appliance fault, then you may be liable for the cost of the call out charge.
United Kingdom Baumatic Ltd., Baumatic Buildings, 6 Bennet Road, Reading, Berkshire RG2 0QX United Kingdom Czech Republic Baumatic CR spol s.r.o. Průmyslová zóna Sever 696 460 11 Liberec 11 Czech Republic Sales Telephone (0118) 933 6900 Sales Fax (0118) 931 0035 Customer Care Telephone (0118) 933 6911 Customer Care Fax (0118) 986 9124 Spares Telephone (01235) 437244 Advice Line Telephone (0118) 933 6933 www.baumatic.cz E-mail: sales@baumatic.co.uk customercare@baumatic.co.uk spares@baumatic.co.