Datasheet

ManualsBrandsBaumer Electric ManualsAngle & Rotary SensorsIncremental Rotary Encoder 65536 PPR 4.75 ... 30VDC 12000min -1

www.baumer.com/motion

Incremental encoders

Subject to modication in technic and design. Errors and omissions excepted.7/1/2019

EIL580P-SC with clamping ange

Features

– Size ø58 mm

– Precise optical sensing (interpolated)

– Output signal level programmable (TTL or HTL)

– Clamping ange

– Connection axial, radial or tangential

– Pulses per revolution 1...65536, programmable

– High protection up to IP 67

– High resistance to shock and vibrations

Technical data - electrical ratings

Voltage supply 4.75...30 VDC

Reverse polarity protection Yes

Short-circuit proof Yes

Consumption w/o load ≤70 mA

Initializing time ≤30 ms after power on

Pulses per revolution 1...65536

Duty cycle 45...55 % typical at 1024, 2048

ppr (further see table Duty

cycle)

Reference signal Zero pulse 90° or 180°

Sensing method Optical

Output frequency ≤300 kHz (TTL)

≤160 kHz (HTL)

Output signals A+, B+, R+, A-, B-, R-

Output stages TTL/RS422

HTL/push-pull

Programmable

parameters

Output level TTL/HTL

Pulse number 1...65536

Zero pulse width 90°/180°

Zero pulse position

Signal sequence

Interference immunity DIN EN 61000-6-2

Emitted interference DIN EN 61000-6-3

Approval UL 508 / CSA 22.2

EIL580P-SC - OptoPulse

Technical data - mechanical design

Size (ange) ø58 mm

Shaft type ø10 x 20 mm, solid shaft with

at

ø3/8" x 4/5" (ø9.525 x

20.32 mm), solid shaft with at

Admitted shaft load ≤40 N axial

≤80 N radial

Flange Clamping ange

Protection DIN EN 60529 IP 65 (without shaft seal),

IP 67 (with shaft seal)

Operating speed ≤6000 rpm (+20 °C, IP 67)

≤12000 rpm (+20 °C, IP 65)

Starting torque ≤0.015 Nm (+20 °C, IP 65)

≤0.02 Nm (+20 °C, IP 67)

Materials Housing: aluminium die-cast

Flange: aluminium

Solid shaft: stainless steel

Operating temperature -40...+100 °C

Relative humidity 90 % non-condensing

Resistance DIN EN 60068-2-6

Vibration 30 g, 10-2000 Hz

DIN EN 60068-2-27

Shock 300 g, 6 ms

Connection Flange connector M12, 8-pin

Flange connector M23, 12-pin

Cable

Weight approx. 300 g

Solid shaft with clamping ange

1…65536 pulses per revolution programmable (interpolated system)

Summary of content (8 pages)

PAGE 1
Incremental encoders Solid shaft with clamping flange 1…65536 pulses per revolution programmable (interpolated system) EIL580P-SC - OptoPulse® Features –– Size ø58 mm –– Precise optical sensing (interpolated) –– Output signal level programmable (TTL or HTL) –– Clamping flange –– Connection axial, radial or tangential –– Pulses per revolution 1...
PAGE 2
Incremental encoders Solid shaft with clamping flange 1…65536 pulses per revolution programmable (interpolated system) EIL580P-SC - OptoPulse® Part number EIL580P-S C . F . 01024 . B Operating temperature B -40...+100 °C Pulses programmable 01024 1...65536 programmable (factory setting: 1024) Voltage supply / output stages F 4.75...
PAGE 3
Incremental encoders Solid shaft with clamping flange 1…65536 pulses per revolution programmable (interpolated system) EIL580P-SC - OptoPulse® Accessories Accessories Connectors and cables Mounting accessories 10127844 Connection cable 2 m shielded with female connector M12, 8-pin, straight (ESG 34FH0200G) 11034138 Spring washer coupling D1=10 / D2=16 (Z 121.
PAGE 4
Incremental encoders Solid shaft with clamping flange 1…65536 pulses per revolution programmable (interpolated system) EIL580P-SC - OptoPulse® Output signals Terminal assignment Flange connector M23, 12-pin / cable Zero pulse electrical 90° A&B high (Factory setting at clockwise rotation (CW) in view of the encoder flange) A+ A- B+ B90° Assignment 1 pink B- 2 – – 3 blue R+ 4 red R- 5 green A+ 6 yellow A- 7 – R-Set 1) 8 grey B+ 9 – – 10 white GND 11 – – 12 brown UB
PAGE 5
Incremental encoders Solid shaft with clamping flange 1…65536 pulses per revolution programmable (interpolated system) EIL580P-SC - OptoPulse® Duty cycle The duty cycle (D) is defined as the time ratio between the HIGH pulse duration (H) and the pulse period (T). System-induced and depending on the pulse number, the measured values may vary which has an impact on speed and position acquisition. Binary pulse numbers are recommended for speed feedback.
PAGE 6
Incremental encoders Solid shaft with clamping flange 1…65536 pulses per revolution programmable (interpolated system) EIL580P-SC - OptoPulse® Dimensions Flange connector M12, radial 10 b 15 38 20° 7 ø48±0.2 11.8 a b ø9.525 8.64 20.32 ø10 9. 20 d g7 a b ø9.525 8.64 20.32 ø10 9. 20 d g7 a b ø9.525 8.64 20.32 ø10 9. 20 d g7 x M3 51.4 a ° (3x) 1 20 ø36h8 ø53±0.05 ø58 )1 20° (3x M4x7 d g7 3 3 M12x1 Flange connector M23, radial 38 3 10 b 3 15 ø36h8 ø53±0.
PAGE 7
Incremental encoders Solid shaft with clamping flange 1…65536 pulses per revolution programmable (interpolated system) EIL580P-SC - OptoPulse® Dimensions Flange connector M12, axial 20° 10 b 15 38 21.8 d g7 a b ø9.525 8.64 20.32 ø10 9. 20 x M3 3 3 7 ø48±0.2 11.1 ø36h8 ø53±0.05 ø58 d g7 a M12x1 ° (3x) 12 20 0° )1 (3x M4x7 Flange connector M23, axial ø9.525 8.64 20.32 ø10 9. 20 M3 3 x7 ø48±0.2 d g7 a ° 20 M4x7 8.
PAGE 8
Incremental encoders Solid shaft with clamping flange 1…65536 pulses per revolution programmable (interpolated system) EIL580P-SC - OptoPulse® Dimensions Cable, tangential 10 b 15 b ø9.525 8.64 20.32 ø10 9. 20 19 Subject to modification in technic and design. Errors and omissions excepted. 7 .5 d g7 a ø36h8 ø53±0.05 ø58 0° ° M3x 5 3 a ° 20 (3x) 12 )1 ø48±0.2 3 128 (3x M4x7 d g7 8 www.baumer.com/motion 7/1/2019 38.