Instruction Manual

ManualsBrandsBaumer ManualsMeasuring instrumentsCombiPress PFMH

www.baumer.com

Operators instructions: 11120948 PFMx Page 1 / 12

Safety instructions

EN/20131117 Design and specifications subject to change without notice

This instrument is built and tested according to the current EU-

directives and packed in a technically safe condition. In order to main-

tain this condition and to ensure safe operation, the user must follow the

hints and warnings given in this instruction.

During the installation the valid national rules have to be observed. Ig-

noring the warnings may lead to severe personal injury or substantial

damage to property.

The product must be operated by trained staff. Correct and safe opera-

tion of this equipment is dependent on proper transport, storage, instal-

lation and operation.

All electrical wiring must conform to local standards. In order to prevent

stray electrical radiation, we recommend twisted and shielded input

cables, as also to keep power supply cables separated from the input

cables. The connection must be made according to the connection dia-

grams.

Before switching on or off the power supply take care that other equip-

ment is not effected. Ensure that the supply voltage and the conditions

in the environment comply with the specification of the device.

Description

The CombiPress

™

PFMN industrial and PFMH hygienic version pressure transmitter is a high end programmable instrument for

measuring pressure from full vacuum to 400 bar gauge pressure or 0 to 400 bar absolute pressure.

CombiPress™ series are supplied to industrial applications with threaded connections or with hygienic connections for hygienic

applications. All wetted parts are in stainless steel AISI 316L (or better). The connection can be mounted as bottom connection or

as rear connection.

PFMx is powered by a 10…35 VDC power supply, featuring an analogue 4...20 mA output signal. A version with 4...20 mA signal

with HART® and an ATEX-version is available.

The CombiPress

™

can be mounted with or without a display. The version with display utilizes the Baumer CombiView™ DFON

display, which is connected to the transmitter via the internal UnitCom ribbon cable. The DFON is supplied with power and a digital

signal for measured value, programming etc., which is more reliable and with better accuracy, than using a 4…20 mA loop. In

instruments with UnitCom both the transmitter and display can be programmed at the same time or separate programming of each

device can be selected.

The DFON has a unique background colour setting. Three colours are available – White / Red / Green and further the red and

green colour can be set as flashing as a warning.

The DFON has two integrated galvanic separated relays. The instrument can be delivered with or without activated relays. If sup-

plied without activated relays, those can be activated by purchasing a license code from Baumer. By entering the code to the in-

strument via the FlexProgrammer the relays are enabled.

The DFON can be programmed by the touch screen on the display or by the FlexProgrammer 9701 Baumer programming unit with

the Baumer FlexProgram installed on a PC.

Operators instructions

CombiPress™, type PFMx

CombiPress

™

PFMx high end pressure transmitter is made for

measuring pressure in all gaseous and liquid processes, within

ranges from full vacuum (-1 bar) to 400 bar gauge.

Summary of content (12 pages)

PAGE 1
Operators instructions CombiPress™, type PFMx CombiPress™ PFMx high end pressure transmitter is made for measuring pressure in all gaseous and liquid processes, within ranges from full vacuum (-1 bar) to 400 bar gauge. Safety instructions This instrument is built and tested according to the current EUdirectives and packed in a technically safe condition. In order to maintain this condition and to ensure safe operation, the user must follow the hints and warnings given in this instruction.
PAGE 2
Operators instructions CombiPress™, type PFMx Warning Factory guarantee is void on mechanical damage of the diaphragm The diaphragm is very sensible and easy to destroy Don’t toutch No high pressure cleaning  Don’t touch the diaphragm  Always put on the protection cap if removing Use no tools the instrument from the application  Don’t use a high pressure cleaner on the diaphragm  Don’t use any tools on the diaphragm, only a soft brush may be used.
PAGE 3
Operators instructions CombiPress™, type PFMx Dimensions Housing Diameter Housing Bottom connection Housing Rear connection Connections for industrial pressure transmitter PFMN Connection 41 G½A Connection 44 G1 conical Connection with cooling neck High temperature types Standard High temp.
PAGE 4
Operators instructions CombiPress™, type PFMx Installation If the transmitter is visibly damaged, it should not be put into operation. The pressure diaphragm must not be touched during installation. Cleaning with high pressure cleaners and tools may damage the diaphragm. If the transmitter has a G½A connection, check before mounting that the depth of the hole is at least 20 mm. For correct installation in 3A connections please see page 2. Mounting the pressure transmitter in a closed system (e.g.
PAGE 5
Operators instructions CombiPress™, type PFMx CombiView™ DFON display There are 9 different display modes available Digital small large Analogue analogue same w. bar graph same w. value Bar graph horizontal vertical Tank tank illustration bottle illustration Electrical connection Electrical connection M12, 5-wire 1 2 3 4 5 + supply, 4...20 mA Common for relays - supply, 4...20 mA Relay 1 Relay 2 M12, 8-wire 1 2 3 4 5 6 7 8 n.c. + supply, 4...20 mA Relay 1 Relay 1 Relay 2 Relay 2 - supply, 4...
PAGE 6
Operators instructions CombiPress™, type PFMx Touch screen programming the CombiView™, type DFON Programming CombiView™, type DFON using the touch screen on the display Tap on the display screen and the Press MENU MENU button will appear in the bottom. and the display will start with the below menu.
PAGE 7
Operators instructions CombiPress™, type PFMx Touch screen programming the CombiView™, type DFON Identification Input Configuration Display output TAG No. / Serial No. / Date / Prod. date Input 100% Current at 100% (20 mA) Input 0% Current at 0% (4 mA) Damping 0 = off / 1...30 sec. Linearization Enable / Disable Display 100% Display value at 100% Display 0% Display value at 0% Decimals Number of digits point Units Rel. / Abs.
PAGE 8
Operators instructions CombiPress™, type PFMx CombiPresS™ w./w.o. DFON - ATEX specifications and instruction PFMx Zone 0 Gas: II 1 G, Ex ia IIC T5 Ga Zone 20 Dust: II 1D, Ex ia IIIC T100°C Da Zone 2 Gas: II 3G, Ex nA II T5 Please ensure that special requirements for installation in the specific environment is followed, as described below. Safety instructions This instrument is constructed and tested according to the current EU directives and packed in a technically safe condition.
PAGE 9
Operators instructions CombiPress™, type PFMx ATEX Gas ia and for ATEX Dust ia For ATEX ia Gas zone 0 and ATEX ia Dust zone 20 a zener barrier must separate the hazardous and safe area and must be installed in accordance with prevailing guidelines for zone 0 / zone 20.
PAGE 10
Operators instructions CombiPress™, type PFMx ATEX Gas nA For ATEX nA zone 2 is approved without using zener barrier to separate the hazardous and safe area and must be installed in accordance with prevailing guidelines for zone 0.
PAGE 11
Operators instructions CombiPress™, type PFMx www.baumer.
PAGE 12
Operators instructions CombiPress™, type PFMx Baumer AG Baumer A/S Hummelstrasse 17 8501 Frauenfeld Switzerland Runetoften 19 8210 Aarhus V Denmark Contact your local Baumer company or Baumer distributor. Please see:  +41 51 / 75 81 122  +45 8931 7611 www.baumer.com/worldwide  +41 52 / 72 81 144  +45 8931 7610 Select your country  sales.ch@baumer.com  sales.cc-lct@baumer.com Select your contact www.baumer.