Instruction Manual

ManualsBrandsBaumer ManualsMeasuring instrumentsCombiView DFON

www.baumer.com

Operators instructions: 11112759 Page 1 / 8

Safety instructions

EN/20131116 Design and specifications subject to change without notice

This instrument is built and tested according to the current EU-

directives and packed in a technically safe condition. In order to main-

tain this condition and to ensure safe operation, the user must follow the

hints and warnings given in this instruction.

During the installation the valid national rules have to be observed. Ig-

noring the warnings may lead to severe personal injury or substantial

damage to property.

The product must be operated by trained staff. Correct and safe opera-

tion of this equipment is dependent on proper transport, storage, instal-

lation and operation.

All electrical wiring must conform to local standards. In order to prevent

stray electrical radiation, we recommend twisted and shielded input

cables, as also to keep power supply cables separated from the input

cables. The connection must be made according to the connection dia-

grams.

Before switching on or off the power supply take care that other equip-

ment is not effected. Ensure that the supply voltage and the conditions

in the environment comply with the specification of the device.

Description

The DFON is powered by the 4…20 mA loop and need no additional power supply. When mounted on new instrument series like

the CombiPress™ PFMx it is via the internal UnitCom ribbon cable supplied with power and a digital signal, instead of integrated in

the 4…20 mA loop. In instruments with UnitCom both the transmitter and display can be programmed at the same time alternative-

ly separate programming of each device can be selected.

The DFON has an unique background colour setting. Three colours are available – White / Red / Green and further the red and

green colour can be set as flashing in warning mode.

The DFON has two integrated galvanic separated relays. The instrument can be delivered with or without activated relays. If sup-

plied without activated relays, those can be activated by purchasing a license code from Baumer. By entering the code to the in-

strument via the FlexProgrammer the relays are enabled.

The DFON can be programmed by the touch screen on the display or by the FlexProgrammer 9701 Baumer programming unit with

the Baumer FlexProgram installed on a PC.

(Free download from www.baumer.com > Services > Downloads > Software < Flex…)

The DFON can be delivered as a loose display or as an integrated part of an instrument e.g. PFMx, TFRx.

Alternatively it can be delivered as a loop-powered local display for any instrument in a SS case for wall mounting, panel mounting

or tube mounting.

Operators instructions

CombiView™, type DFON

DFON graphical displays are used as separate units, but also used

in complete instruments,

e.g. CombiPress™, CombiTemp™

Summary of content (8 pages)

PAGE 1
Operators instructions CombiView™, type DFON DFON graphical displays are used as separate units, but also used in complete instruments, e.g. CombiPress™, CombiTemp™ Safety instructions This instrument is built and tested according to the current EUdirectives and packed in a technically safe condition. In order to maintain this condition and to ensure safe operation, the user must follow the hints and warnings given in this instruction. During the installation the valid national rules have to be observed.
PAGE 2
Operators instructions CombiView™, type DFON Display mode There are 9 different display modes available Digital small large Analogue analogue same w. bar graph same w.
PAGE 3
Operators instructions CombiView™, type DFON Touch screen programming the CombiView™ , type DFON Programming CombiView™, type DFON using the touch screen on the display Tap on the display screen and the Press MENU MENU button will appear in the bottom. and the display may start with one out of two possible selections.
PAGE 4
Operators instructions CombiView™, type DFON Touch screen programming the CombiView™, type DFON www.baumer.
PAGE 5
Operators instructions CombiView™, type DFON CombiView™, type DFON - ATEX specifications and instruction Zone 0/1 Gas: II 1 G, Ex ia IIC T5 Gas Zone 20/21 Dust: II 1 D, Ex ia IIIC T100°C Da Zone 2 Gas: II 3 G, Ex nA II T5 Please ensure the special requirements for installation in the specific environment is followed, as described below. ATEX approval requires the CombiView™, type DFON to be installed in IP67 certified housing, such as Baumer FlexHousing.
PAGE 6
Operators instructions CombiView™, type DFON ATEX Gas ia and for ATEX Dust ia For ATEX ia Gas zone 0 and ATEX ia Dust zone 20 a zener barrier must separate the hazardous and safe area and must be installed in accordance with prevailing guidelines for zone 0 / zone 20.
PAGE 7
Operators instructions CombiView™, type DFON ATEX Gas nA For ATEX nA zone 2 is approved without using zener barrier must separate the hazardous and safe area and must be installed in accordance with prevailing guidelines for zone 0.
PAGE 8
Operators instructions CombiView™, type DFON Baumer AG Hummelstrasse 17 8501 Frauenfeld Switzerland  +41 51 / 75 81 122  +41 52 / 72 81 144  sales.ch@baumer.com www.baumer.com Baumer A/S Runetoften 19 8210 Aarhus V Denmark  +45 8931 7611  +45 8931 7610  sales.cc-lct@baumer.com Contact your local Baumer company or Baumer distributor. Please see: www.baumer.