Owner manual

Product Specication
EXG series – State-of-the-art CMOS Matrix Cameras
Simple integration by GigE Vision ▪
®
compliance
Resolution up to 5.0 megapixels in color and monochrome ▪
Innovative technology with High Dynamic Range (HDR), Auto-Exposure and Auto- ▪
Gain
Minimal dimensions with 36 x 36 x 42 mm ▪
Camera Type
Sensor
Size
Resolution
Full Frames
[max. fps]
Monochrome / Color
EXG03 / EXG03c 1/3" 752 x 480 / 748 x 476 60
EXG50 1/2.5" 2592 x 1944 14
Dimensions
26
26
36
36
4
x
M
3
36
36
42
C-Mount
System Requirements
Single-camera system Multi-camera system
Minimum Recommended Minimum Recommended
CPU
Intel
®
Pentium
®
4
or comparable
processor
Intel
®
Core™ Duo comparable processor
Clock 2.5 GHz > 2.5 GHz 2.5 GHz 3 GHz
RAM 1024 MB 2048 MB 2048 MB > 2048 MB
Operating
system
(OS)
Microsoft
®
Windows
®
XP incl. Service Pack 2 or higher
Microsoft
®
Windows
®
XP x64 incl. Service Pack 2 or higher
Microsoft
®
Windows Vista™ 32 / 64 bit systems
Linux
®
32 / 64 bit systems from Kernel 2.6.xx
Graphic recommended resolution 1280 x 1024, color depth at least 16 bit
Ethernet Gigabit Ethernet compliant NIC (recommended Intel
®
chipset)
Framework
(optional)
Windows
®
OS: .NET™ Framework 2.0 or higher
Linux
®
OS: Mono 1.2.4 or higher
Process and Data Interfaces
8P8C mod jack M8 3 pins M8 4 pins
18
1
4
3
1
2
4
3
1 (gn/wh) MX1+ 1 (bn) Power V
CC
1 (bn) TrigIN+
2 (gn) MX1- 3 (bu) GND 2 (wh) TrigIN-
3 (og/wh) MX2+ 4 (bk) NC 3 (bu) Flash
out
4 (bu) MX3+ 4 (bk) U
ext
5 (bu/wh) MX3-
6 (og) MX2-
7 (bn/wh) MX4+
8 (bn) MX4-
Power Supply
Power V
CC
8 VDC ... 30 VDC
Current I 620 mA ... 120 mA
Power consumption P approx. 3.5 ... 6 W
LED Signaling
1
2
LED Signal Meaning
1
green Power on
yellow Readout active
2
green Link active
green ash Receiving
yellow Transmitting
yellow / red ash Receiving and Transmitting
Safety
Further Information
For further information on our products visit www.baumeroptronic.com
For technical issues, please contact our technical support:
[e-mail] · Phone [phone] · Fax [phone]
© Baumer Optronic GmbH · Badstrasse 30 · DE-01454 Radeberg, Germany
Technical data has been fully checked, but accuracy of printed matter not guaranteed.
Subject to change without notice. Printed in Germany 12/04. V1.1 11037878
FCC – Class B device
No t e : This equipment has been tested and found to
comply with the limits for a Class B digital device, pursu-
ant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interfer-
ence in a residential environment. This equipment gener-
ates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructios,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occure in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off an
on, the user is encouraged to try to correct the interference
by one or more of the following measures:
Reorient or relocate the receiving antenna. ▪
Increase the separation between the equipment and the ▪
receiver.
Connect the equipment into an outlet on a circuit different ▪
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician ▪
for help.
Conformity:
CE, FCC Part 15 Class B, RoHS
Safety Precautions
Notice
See user´s Guide for the comple-
te safety instructions!
Protect the sensor from dirt and ▪
moisture.
Never open the camera housing. ▪
Avoid camera contamination by ▪
foreign objects.
Environmental requirements:
Storage temp. -10°C ... +70°C
Operating temp. +5°C ... +50°C
Housing temp. max. +50°C
Humidity 10 % ... 90 %
Non-condensing
Tested according to standard
EMVA 1288
Quick Start Guide
EXG Gigabit Ethernet cameras
Further technical
details available in
the respective data
sheets.
Installation
Installation of standard cameras:
Connect the camera using an ▪
appropriate cable (at least Cat-
5e) to the GigE board on your
PC (8P8C mod jack)
If required, connect a trigger ▪
and / or flash to the 4-pin M8
male connector
Connect the camera to power supply ▪
Mounting Adapters
Name Item-No.
Tripod mounting adapter 11003060
Front mounting adapter 11002638
open wire
Installation sample
1 - PCI board; 2 - GigE cable;
3 - Cable for trigger and ash; 4 - Power cable
Documentation and Software
Notice
w
w
w
.
b
a
u
m
e
r
.
c
o
m
The product documentation and software as well as accom-
panying tools and applications notes can be obtained in the
download area:
http://www.baumer.com/de-en/services/member-area/
A registration is required.