Owner manual

ManualsBrandsBaumer ManualsMeasuring instrumentsTE2

Page 1 Design and speciﬁcations subject to change without notice

Installation Manualwww.baumer.com/process

TE1/TE2 - Pt100 Temperature System

TE1

temperature-

sensor or

transmitter

TE2

temperature

sensor

Use only the recommended sleeves or adapters. If other systems are

used, there is a severe risk of system malfunction or untight process

connections.

Do not use Teﬂon, elastomere or other types of gaskets for the

hygienic process connection featuring a conical seal.

The tightening torque is 10...20 Nm.

Mechanical Installation - Mounting Examples Mounting a Welding Part

10...20 Nm.

The hygienic welding parts are easy to weld into tank walls and pipes.

The mark or hole on the welding part indicates the ﬁnal position of the

cable gland or M12 connector for a TE1/TE2 sensor.

We recommend to position the gland or plug downwards in order to

avoid water intrusion.

Check the tightness of the process connection. Make sure that the

cable gland or the M12 plug connector is properly screwed in.

Mark

M12 connection No thread G1/2A hygienic

PM031 CAM020

TE2

temperature

transmitter

Safety instructions

This instrument is built and tested according to the current EU-direc-

tives and packed in technically safe condition. In order to maintain this

condition and to ensure safe operation, the user must follow the hints

and warnings given in this instruction.

During the installation the valid national rules have to be observed.

Ignoring the warnings may lead to severe personal injury or substan-

tial damage to property.

The product must be operated by trained staff. Correct and safe op-

eration of this equipment is dependent on proper transport, storage,

installation and operation.

All electrical wiring must conform to local standards. In order to

prevent stray electrical radiation, we recommend twisted and shielded

input cables, as also to keep power supply cables separated from the

input cables. The connection must be made according to the connect-

ing diagrams.

Before switching on the power supply take care that other equipment

is not affected. Ensure that the supply voltage and the conditions in

the environment comply with the speciﬁcation of the device.

Before switching off the supply voltage check the possible effects on

other equipment and the processing system.

WARNING

This product contains no replaceable parts.

In case of malfunction the product must be shipped to Baumer for

repair.

10...20 Nm.

Summary of content (4 pages)

PAGE 1
TE1/TE2 - Pt100 Temperature System Safety instructions This instrument is built and tested according to the current EU-directives and packed in technically safe condition. In order to maintain this condition and to ensure safe operation, the user must follow the hints and warnings given in this instruction. During the installation the valid national rules have to be observed. Ignoring the warnings may lead to severe personal injury or substantial damage to property.
PAGE 2
Electrical Installation TE1/TE2 Temperature Sensor TE2 - Integrated Temperature Transmitter Pt100 Pt100 - Pt100 4...20 mA 4 1 4 2 3 2 3 M12 Plug 4...20 mA - + 3 3 1 + Male plug 1 2 1 2 2 Plug DIN 43650-A Pt100 1 Plug DIN 43650-A M12 Plug Application Examples TE2 with Integrated Transmitter and ZED601 Note: The lamp is controlled by the open collector output (PNP) from the ZED601 (optional). 230 Vac Lamp 3 1 2 3 4 1 2 4...
PAGE 3
Configuration with FlexProgrammer Note: Disconnect loop supply before connecting the FlexProgrammer to the transmitter. FlexProgrammer 9701 Red clip 1 2 1 1 Black clip 2 2 Note: Ambient temperature range 0...50°C TE2 with integrated transmitter FlexTop transmitter 1 2 Brown 1 2 1 2 Adapter cable for TE2 with integrated transmitter In the following description the TE2 with an integrated transmitter and the TE1 with a FlexTop temperature transmitter will be referred to as “transmitter”.
PAGE 4
Samples of Accessories In case the TE1 is equipped with a FlexTop in-head transmitter or the TE2 is with internal transmiiter the Flexprogrammer will be needed. A full range of accessories for TE1 and TE2 can be found in the data sheet ”Accessories” The FlexProgrammer 9701 is a dedicated tool to configure all Baumer configurable products. Type No. 9701-0001 complies: FlexProgrammer interface unit CD with the FlexProgram software and product drivers (DTM) USB cable Cable with 2 alligator clips Max.