amplified installation manual If you have any questions contact the SAS Technical Support Department at: Phone - (504) 272 7135 Fax - (504) 272-9844 Email - tech@sasbazooka.com Website - www.sasbazooka.com In Canada: (604) 988 2966 15049 Florida Blvd., Baton Rouge, LA.
CONGRATULATIONS Dear Friend, Thank you for selecting Bazooka® subwoofer speaker systems for your car stereo system. The Bazooka EL series represents SAS‘s continued commitment to efficiency and design. An innovative manufacturing process developed by SAS for the Bazooka provides consumers with state-of-the-art speaker system design.
CONTENTS INPUT SIGNAL CONNECTIONS Should I Use High or Low Level Inputs? If the source unit has only speaker outputs, use the high-level inputs of the Amplified Bazooka. If the source unit has both high and low level outputs, we recommend using the high level inputs over the low level inputs, due to the configuration of the Amplified Bazooka's balanced input circuit. PLEASE NOTE THAT THE WIRING IN A FACTORY STEREO MAY NOT BE ELECTRICALLY IN PHASE EVEN WHEN YOU HAVE MADE THE PROPER CONNECTIONS.
TURN ON OPTIONS CONT. SYSTEM FEATURES 5”, 6.5”, or 8” SUBWOOFER PATENTED BASS TUBES ® ENCLOSURE WITH BASS REFLEX/DUCTED PORT ALIGNMENT HIGH EFFICIENCY OUTPUT OPTIMIZED FOR SPACE EFFICIENCY DESIGNED FOR CORNER LOADING MOISTURE RESISTANT ENCLOSURE BUILT IN 30 WATT MONO AMPLIFIER @ 2 OHMS AMP IS 2 OHM STABLE 18dB ELECTRONIC CROSSOVER FIXED @ 120 Hz.
INSTALLATION GROUND WIRE The 16 gauge black wire on the 14-pin Molex Mini-fit Jr. connector is the negative ground wire. It must be connected directly to the vehicle chassis near the amplifier. We do not recommend extending the ground wire in any installation, as this can cause unwanted ground loops. The ground point in the car should be a piece of chassis metal that is part of or welded to the main body of the vehicle.
INSTALLATION POWER WIRE Please take time to read through this manual and plan out your installation before you begin! Locate an area in the rear of the vehicle where you would like to place the Bazooka speaker systems. The location you have selected must meet the following requirements in order for the Bazooka to be properly installed in the vehicle: The 16 gauge red wire on the 14-pin Molex Mini-fit Jr. connector is the 12 Volt positive power wire.
MOUNTING THE BAZOOKA WIRING DIAGRAM When using high level inputs, take the time after you make all wiring connections to run through the AM I IN PHASE procedure of this manual to confirm that your inputs are in correct electrical phase and the proper bass response is being produced. 1. With the top side of the buckle facing up (see figure 4), lace the strap through the mounting base as illustrated in figure 5.
MOUNTING THE BAZOOKA MOUNTING THE BAZOOKA 3. Place each mounting base under the Bazooka so that the apex at the bottom of the tube sits inside the mounting base as in figure7. See Model Size For Length Figure 9 4. Move the bases so that they are spaced approximately 3” from each end of the enclosure as illustrated in figure 8. Figure 7 Model EL5A EL6A EL8A 8. Remove any slack in the strap by feeding it out of the mounting base on the loose end of the strap opposite the buckle. Length 12” 17” 22” 9.
MOUNTING THE BAZOOKA MOUNTING THE BAZOOKA 3. Place each mounting base under the Bazooka so that the apex at the bottom of the tube sits inside the mounting base as in figure7. See Model Size For Length Figure 9 4. Move the bases so that they are spaced approximately 3” from each end of the enclosure as illustrated in figure 8. Figure 7 Model EL5A EL6A EL8A 8. Remove any slack in the strap by feeding it out of the mounting base on the loose end of the strap opposite the buckle. Length 12” 17” 22” 9.
MOUNTING THE BAZOOKA WIRING DIAGRAM When using high level inputs, take the time after you make all wiring connections to run through the AM I IN PHASE procedure of this manual to confirm that your inputs are in correct electrical phase and the proper bass response is being produced. 1. With the top side of the buckle facing up (see figure 4), lace the strap through the mounting base as illustrated in figure 5.
INSTALLATION POWER WIRE Please take time to read through this manual and plan out your installation before you begin! Locate an area in the rear of the vehicle where you would like to place the Bazooka speaker systems. The location you have selected must meet the following requirements in order for the Bazooka to be properly installed in the vehicle: The 16 gauge red wire on the 14-pin Molex Mini-fit Jr. connector is the 12 Volt positive power wire.
INSTALLATION GROUND WIRE The 16 gauge black wire on the 14-pin Molex Mini-fit Jr. connector is the negative ground wire. It must be connected directly to the vehicle chassis near the amplifier. We do not recommend extending the ground wire in any installation, as this can cause unwanted ground loops. The ground point in the car should be a piece of chassis metal that is part of or welded to the main body of the vehicle.
TURN ON OPTIONS CONT. SYSTEM FEATURES 5”, 6.5”, or 8” SUBWOOFER PATENTED BASS TUBES ® ENCLOSURE WITH BASS REFLEX/DUCTED PORT ALIGNMENT HIGH EFFICIENCY OUTPUT OPTIMIZED FOR SPACE EFFICIENCY DESIGNED FOR CORNER LOADING MOISTURE RESISTANT ENCLOSURE BUILT IN 30 WATT MONO AMPLIFIER @ 2 OHMS AMP IS 2 OHM STABLE 18dB ELECTRONIC CROSSOVER FIXED @ 120 Hz.
CONTENTS INPUT SIGNAL CONNECTIONS Should I Use High or Low Level Inputs? If the source unit has only speaker outputs, use the high-level inputs of the Amplified Bazooka. If the source unit has both high and low level outputs, we recommend using the high level inputs over the low level inputs, due to the configuration of the Amplified Bazooka's balanced input circuit. PLEASE NOTE THAT THE WIRING IN A FACTORY STEREO MAY NOT BE ELECTRICALLY IN PHASE EVEN WHEN YOU HAVE MADE THE PROPER CONNECTIONS.
CONGRATULATIONS Dear Friend, Thank you for selecting Bazooka® subwoofer speaker systems for your car stereo system. The Bazooka EL series represents SAS‘s continued commitment to efficiency and design. An innovative manufacturing process developed by SAS for the Bazooka provides consumers with state-of-the-art speaker system design.
amplified inst If you have any questions contact the SAS Technical Support Department at: Phone - (504) 272 7135 Fax - (504) 272-9844 Email - tech@sasbazooka.com Website - www.sasbazooka.com In Canada: (604) 988 2966 15049 Florida Blvd., Baton Rouge, LA.