Models: NOS6, NOS8, NOS8A, NOS8P, NOS8W, SCUBA8
Dear Friend, Thank you for selecting Bazooka® Mobile Audio for your car stereo system. This Bazooka subwoofer represents our continued commitment to efficiency and design. An innovative manufacturing process we developed for the Bazooka provides consumers with state-of-the-art speaker system design. At Bazooka Mobile Audio, we take pride manufacturing the most revolutionary bass speaker systems ever created, featuring our patented Bass Tubes® enclosure design, and we hope you will take pride in owning them.
CONTENTS Warranty pg 2 System Features pg 3 Specifications pg 3 Pre Installation pg 4, 5 Finishing The Look Part 1 pg 5 Finishing The Look Part 2 pg 6 Vehicle Placement pg 7 Mounting The Subwoofer pg 8 Wiring pg 9, 10 WARRANTY All SAS® subwoofer products are covered under warranty for ONE full year from the date of purchase. Terms and conditions of the warranty are as stated on the warranty card included in the box with the product.
SYSTEM FEATURES 6 or 8 PURE-PISTON WOOFER 150 WATT HIGH POWER AMP (NOS8A ONLY) TURBO COOLED VOICE COILS BASS REFLEX, DUCTED PORT ENCLOSURE CORNER LOADING COPLANAR OUTPUT HIGH OUTPUT EFFICIENCY MOISTURE RESISTANT ENCLOSURE AND WOOFER MAXIMIZED SPACE EFFICIENCY 1 YEAR WARRANTY LARGE MAGNET FOR INCREASED POWER HANDLING SPECIFICATIONS: PASSIVE UNITS Woofer Size Voice Coil Size Magnet Size Frequency response* Efficiency* Power Handling Dimensions Weight Impedance 6.
INSTALLATION Please take time to read through this manual and plan out your installation before you begin! Locate an area in the rear of the vehicle where you would like to place the Bazooka speaker systems. The location you have selected must meet the following requirements in order for the Bazooka to be properly installed in the vehicle: 1.) The woofer (grill end) should be facing into a corner. (See vehicle placement recommendations on page 5) 2.
FINISHING THE LOOK (Step 1) In order to complete the look of your subwoofer, you will need to install the included wire loom over the wire and attach the nozzle to the top of the tank. To begin, the wiring needs to be routed THROUGH the nozzle. If necessary, begin by feeding the wire through the nozzle as shown in the picture below. Continue feeding wire through as you push the nozzle into the top of the tank until you hear a click.
FINISHING THE LOOK (Step 2) Next, install the wire loom by pushing the loom onto the wire, as shown in below. Starting from the free end and working your way up to the nozzle. (Note: Pulling the wire loom will result in binding, making it more difficult to put the loom in place.) Remove the locking nut from the nozzle by turning counter-clockwise ¼ turn.
VEHICLE PLACEMENT RECOMMENDATIONS TRUCK INSTALLATION tube size is exaggerated for emphasis HATCHBACK INSTALLATION tube size is exaggerated for emphasis SEDAN INSTALLATION tube size is exaggerated for emphasis 7
Mounting the NOS Tube: Once you have found a suitable location, you need to mount the NOS Tube. Mounting the unit ensures that it will give you years of troublefree performance, and also guarantees that your unit is correctly oriented for it to operate properly. To begin, mount the bases parallel on the floor of the vehicle with the bases EXACLTY 13 inches apart, from inside edge to inside edge. Mounting these brackets incorrectly will make the final mounting steps difficult or impossible.
WIRING DIAGRAM (NOS8A Only) Black Red RCA Green/White RCA Brown/Grey Orange RED 12 GAuge + 12 Volt Battery BLACK 12 Gauge Chassis Ground Orange 16 Gauge Remote Turn-On Green/White RCA Right RCA Input Brown/Grey RCA Left RCA Input POWER WIRE (NOS8A only) The power wire must be fused and connected directly to the positive terminal of the battery to provide a power source with a low voltage drop and low noise. Do not make the power connection at the fuse block or any point other than the battery.
antenna or power leads, or near sensitive equipment or harnesses. The power wire carries substantial currents and could induce noise. GROUND WIRE (NOS8A only) The ground wire must be connected directly to the vehicle chassis near the amplifier. We do not recommend extending the ground wire in any installation, as this can cause unwanted ground loops.The ground point in the car should be a piece of chassis metal that is part of or welded to the main body of the vehicle.
If you have any questions contact the SAS Technical Support Department at: Phone - (800) THE TUBE Fax - (225) 272-9844 In Canada: (604) 988 2966 Email - tech@bazooka.com Website - www.bazooka.com 15049 Florida Blvd., Baton Rouge, LA. 70819 SAS, BAZOOKA, BASS TUBES, and LISTEN TO YOUR EARS are registered trademarks of Southern Audio Services, Inc. PAT. NO.
