TA850C BTA850FH
ENGLISH Dear Friend, Thank you for selecting Bazooka® subwoofer speaker systems for your stereo system. Today, the Bazooka represents Bazooka Mobile Audios continued commitment to efficiency and design. An innovative manufacturing process developed by SAS® for the Bazooka provides consumers with state-of-the-art speaker system design.
CONTENTS PG 3 VEHICLE PLACEMENT RECOMMENDATIONS PG 4 MOUNTING THE BAZOOKA PG 5-7 WIRING DIAGRAM PG 8 SPECIFICATIONS PG 9 WIRING PG 10-12 TROUBLESHOOTING PG 13-14 WARRANTY PG 15-16 2 ENGLISH HELPFUL HINTS BEFORE YOU BEGIN
HELPFUL HINTSBEFORE YOU BEGIN ENGLISH Please take time to read through this manual and plan out your installation before you begin! Locate an area in the rear of the vehicle where you would like to place the Bazooka speaker systems. The location you have selected must meet the following requirements in order for the Bazooka to be properly installed in the vehicle: 1) The woofer (grill end) should be facing into a corner. (See vehicle placement recommendations on pg.
VEHICLE PLACEMENT RECOMMENDATIONS TRUCK INSTALLATION HATCHBACK INSTALLATION tube size is exaggerated for emphasis SEDAN INSTALLATION tube size is exaggerated for emphasis 4 ENGLISH tube size is exaggerated for emphasis
MOUNTING THE BAZOOKA ENGLISH Figure 1 Top Logo should face up 1. With the topside of the buckle facing up (see figure 1), lace the strap through the mounting base as illustrated in figure 2 Figure 2 Figure 3 2. After the strap is completely laced through the mounting base, make a loop with the strap, where it runs across the middle of the base as illustrated in figure 3. This loop is necessary to access the two mounting holes in the base.
ENGLISH Figure 4 3. Place each mounting base under the Bass Tubes® enclosure so that the apex at the bottom of the tube sits inside the mounting base as in figure 4. 3 ,, Figure 5 3 ,, 4. Move the bases so that they are spaced approximately 3 from each end of the enclosure as illustrated in figure 5. 5. Remove the Bass Tubes® enclosure without moving the mounting bases and set it aside. 6. Screw each mounting base securely in place with screws provided as illustrated in figure 3.
BTA850C WIRING DIAGRAM
*Not applicable to the TA850C & BTA850FH TA850C & BTA850FH are 2 Ohm products
ENGLISH Low-Level Inputs: If your source unit only has low-level RCA phono jack output, use only the low-level inputs of the Amplified Bazooka. Connect the low-level RCA phono jack inputs of the Amplified Bazooka subwoofer to the source with a shielded RCA patch cord. To avoid possible noise problems, be sure to run the patch cord away from all power wires and factory wire harnesses.
OPTION ONE: When you are using this option with all amplified Bass Tubes® models: For the most versatility the Orange Remote Turn On Wire should be connected to the source unit's "Accessory", "Auto-Antenna" or "Remote" lead -- any of which will supply 12 Volts positive when the source is turned on.
ENGLISH TROUBLESHOOTING Am I In Phase? If your inputs are out of phase and you turn the balance control of your radio all the way to one side, right or left, the bass output from the Bazooka® will increase. When you bring the balance control back to the center position the bass level will drop. This confirms that one of your input channels is wired out of phase with the other.
PHASE CORRECTING PROCEDURE Disconnect all but one Bazooka® from your system. Be sure that any loose wire connections are insulated to avoid the chance of short-circuiting any of the electronic equipment. Listen to the system and take note of the level of the Bass Response. Connect the next Bazooka® and compare the level of the combined output to that of the single unit. If the Bass Response increases, the Phasing is correct and you can repeat this process on the next Bazooka.
ENGLISH LIMITED WARRANTY (UNITED STATES) Southern Audio Services, Inc., warrants all products to be free from defects in material and workmanship for a period of one (1) year from the date of purchase. In the event the product is not as warranted, SAS sole obligation shall be to repair or replace the defective product at SAS option: SAS limits its obligation under any implied warranties under state laws to a period not to exceed the limited warranty period.
____________________________________________ MODEL# ____________________________________________ SERIAL# ____________________________________________ PURCHASE DATE ____________________________________________ DEALER PURCHASED FROM ____________________________________________ DEALER ADDRESS ____________________________________________ TELEPHONE ____________________________________________ PURCHASERS NAME ____________________________________________ STREET ADDRESS ____________________________________________