|Page
Index: Page Page Page Page Page Page Page Page Page Page Page 2 - Index 3 - Hardware info 4 - Software Introduction 5 - Default settings 6 - Manual operation 7 - DMX Operation 7 - Tweaking 8 - Mode features 9 - Menu tree 11 - DMX Channels 13 - FAQ Intro: Brother, Brother & Sons ApS The information in this manual is subject to change without notice. Brother, Brother & Sons ApS assumes no responsibility for any errors or inaccuracies that may appear in this manual.
Hardware Info: 4 Bank: AC Power: 100 – 240 V nominal, 50/60 Hz Never connect to dimmer power Powersupply: Electronic switchmode This fixture must be connected to ground. 48 Volt PSU IN Pin assignment: Pin 1: GND / PIN 4: + 3 Foot specific: Weight: 4.1 kg / 9.04 lbs 108W 4 Foot specific: 5 kg / 11.2 lbs 144W Thermal: Maximum ambient temperature - t.Amb: 40° C / 104° F Specifications subject to change without notice. For the latest specifications see www.brothers-sons.
Software Introduction: A. The Pipeline 4 Banks has 4 Pipes and a Controlbox B. The Pipeline 4 Banks can be divided into two groups: Fixed and Tweaking. C. The Pipeline System 4 Banks has 2 to 3 basic functions D. The Pipeline 4 Banks has 6 different modes A. Pipes and Controlbox The Pipes has a color temperature of 3200, 4300 or 5600K The 4 Banks have 4 Pipes, that comes as either 4 x 3200K (Fixed), 4 x 4300K (Fixed), 4 x 5600K (Fixed) or 2 x 3200K + 2 x 5600K (Tweaking) B.
D. Modes (can be set in the menu under Mode/Resolution:) CCT 8bit - Color Tweak from 3200K - 5600K (Can be selected for any Pipeline 4 Bank, but only works for Pipeline 4 Bank Tweaking) (4300K and unknown tubes will not switch on when using CCT mode.) CCT 16bit - High Resolution Intensity and Color Tweak from 3200K - 5600K (Can be selected for any Pipeline 4 Bank, but only works for Pipeline 4 Bank Tweaking) (4300K and unknown tubes will not switch on when using CCT mode.
Manual operation (No DMX connected) The way the manual operation works is dependent on the resolution setting. If set to All 8 / All 16 When the Pipeline 4 Bank is switched on the display will show the light level e.g. “ 0” Use the UP and DOWN buttons to set the desired light level. The level will be autosaved after 10 seconds, indicated by display readout “SAVED” or can be saved instantly by pressing ENTER after setting the light level.
DMX Operation: Starting up: At start up, display reads out the DMX address. When a DMX cable is connected and the Pipeline 4 Bank receives a valid DMX signal from a DMX controller, the unit will indicate that DMX is being received by turning on the DMX present indicator in the display. (See Introduction) If a unit is started up without DMX present it will start up in manual mode, but will switch to DMX mode as soon as a DMX signal is detected.
MODE FEATURES EXPLAINED Resolution: All: Controls all pipes as one Ind: Controls all pipes individually CCT: An overall light level and color balance can be set. 8 bit: Less DMX channels used. 16 bit: Smoother resolution. Response: Slow: Fades between values. Smoother fades. Fast: Snaps between values. Fast operation. Curve: Square: Dimmer curve designed for LEDs Linear: Standard dimmer curve Strobe: OFF: Less DMX channels used. ON: Strobe function added.
MENU TREE Button actions: Menu: In and out of Menus - Up+Down: Navigate and change values - Enter: Select and Save A.
Color Calibration CalVal Reset testdisplay Log Manual: BEWARE: In this menu you can set the color of the Installed pipes. You do not need to change these settings. This will NOT affect the color of the pipes. It will only inform the software about what Pipes are installed. If you change the color settings of the pipes here, it will affect the functionality of a tweaking unit. It will affect a Fixed unit if a pipe is set to None Resetting the fixture will not reset the any changes made to these settings.
DMX Channels: Mode CCT 8 bit Channel 1 2 Parameter Intensity Color Function Intensity Warm White - Cold White Value 0 - 255 0 - 255 Percent 0 - 100 0 - 100 Mode CCT 8 bit - Strobe ON Channel 1 2 3 Parameter Intensity Color Strobe Mode 4 Strobe Lenght Function Intensity Warm White - Cold White Open Fast to Slow Strobe Open Slow to Fast Strobe - Random Open Short to Long Flash Value 0 - 255 0 - 255 0- 5 6 - 125 126 - 130 131 - 250 251 - 255 0 - 255 Percent 0 - 100 0 - 100 0 1 - 49 50 51 - 99 100
Mode Individual 16 bit Channel 1 2 3 4 5 6 7 8 Parameter Intensity Intensity Intensity Intensity Intensity Intensity Intensity Intensity Function Intensity Pipe A - Coarse Intensity Pipe A - Fine Intensity Pipe B - Coarse Intensity Pipe B - Fine Intensity Pipe C - Coarse Intensity Pipe C - Fine Intensity Pipe D - Coarse Intensity Pipe D - Fine Value 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 0 - 255 Percent 0 - 100 0 - 100 0 - 100 0 - 100 0 - 100 0 - 100 0 - 100 0 - 100 Mode Individual 16
FAQ - TROUBLE SHOOTING Power is on but the display is not 1. Press a button to activate, if Display has been set to "Off after 2 minutes" 2. Check if the light is on in your PSU The luminaire is flashing 1. Check to see if you have set it for strobing. 2. Check your patch 3. You are in the Color menu The light on the PSU is flashing 1. There’s a short curcuit - Contact your dealer In manual mode “ENTER” only switches between “MANUAL” and the saved light level in the display, but not in the output. 1.