Mobiband Bluetooth Stereo Headphones with Mic User’s manual www.bbp-industries.com www.bbpbags.
Contents Brief introduction………………………………….…………...…1 1. Bluetooth wireless communication technology…...………….….....1 2. About the Mobiband…………………………..…….………….…..1 Before use…………………………………………………...……..2 1. Overview……………………………..………………..…………...2 2. Charging the headset………………………….………………....…3 Getting started.……………………………….………….………..3 1. Turning on/off the headset……………….……….……………...…3 2. Pairing the headset with Bluetooth devices…………………..….....4 How to enter pairing mode……………………..……………….....
Welcome to use this Bluetooth stereo headset, Mobiband. Please read this user’s manual carefully before use. Brief introduction 1. Bluetooth wireless communication technology Bluetooth is a standard of close range wireless communication technology that was drawn up by Ericsson, IBM, Intel, Nokia and Toshiba. With Bluetooth technology, we can achieve the highest transmission rate among cell phones, computers, printers, PDAs and other devices.
1 3) Easy to switch between the call and music, you will not miss the incoming call during listening to music. 4) Every time the headset is tured on, it will connect to last connected device automatically. Note: Even though the paired device and the headset support the same Bluetooth profiles, functions may vary due to specification differences of the paired devices. Before use 1.
2 2. Charging the headset The headset comes with a built-in rechargeable battery, prior to using it, it is recommended to charge the battery fully for the first time. When the headset is low power, red LED flashes twice and the headset emits three “Dong” tones every 20 seconds. Please recharge the battery of the headset. 1) Using travel charger Connect the charger to a standard power outlet and the charger plug to the charging jack of the headset. Red LED is on while charging.
3 Remark: In order to save power, the headset will turn off automatically if no devices can be connected after 5 minutes. 2. Pairing the headset with Bluetooth devices How to enter pairing mode Function Operation Entering pairing mode LED indicator LED flashes red and blue alternately Ensure the headset is turned off, otherwise turn it off first and then press and hold MFB button for 6～7 seconds until LED flashes red and blue alternately Remark: Pairing mode will last 2 minutes.
4 After pairing is successful, the headset and the cell phone will remember each other, they will no need to re-pair next time. The headset can remember 8 paired devices, When the number of paired devices exceeds 8, the first one will be replaced. Every time the headset is turned on, it will connect to last connected device automatically.
5 Multi-pairing The headset can connect with two devices at most. One is a Bluetooth cell phone supporting HFP profile, the other one is a Bluetooth music device supporting A2DP profile.
6 4. Wearing the headset The headband of the headset is foldable and retractable, please adjust according to the actual use. Logo “L” of the headset represents left ear, Logo “R” of the headset represents right ear. Please wear the headset according to the indication of the Logo. 5.
7 Status of Mobiband Operation Voice dial Standby mode and connected to a device Simultaneously press and hold MFB buttons for 2 seconds and release them until hearing indication tone Redial last number Standby mode and connected to a device Short press MFB button twice Lock/unloc k the buttons Standby mode Clear pairing list Charging Function Simultaneously press and hold MFB and＋buttons for 2 seconds and release them until hearing indication tone Firstly press and hold MFB button and then pre
8 Remarks: Not all cell phones support all functions listed above. Please refer to your cell phone’s user’s manual for further information. Certain functions and indication tones maybe vary with different models of cell phones. When the volume is adjusted to max. or min., you will hear a indication tone. When pressing the answer button on some cell phones, the call will be transferred to the cell phone. You have to switch the call to the headset manually then.
9 When the volume is adjusted to max. or min., you will hear a indication tone. If you want to remote control previous/next track, pause/play, it needs your Bluetooth cell phone or Bluetooth transmitter paird with the headset to support AVRCP profile, please refer to the user’s manual of your cell phone or Bluetooth transmitter for further information. 7.
10 8. Indication tone Indication tone Two short “DU” tones Emits 2 tones every 5 seconds Emits 3 “Dong” tones every 20 seconds Status of Mobiband Enter pairing mode During a call (Microphone mute) Low power Care and maintenance Read the following recommendations before using the headset. Following these you will be able to enjoy the product for many years. Do not expose the headset to liquid, moisture or humidity to avoid the product’s internal circuit being affected.
11 3 How far is the effective range between the headset and Bluetooth cell phone? According to the Bluetooth standard, the max. controllable range of Class II headset is 10 meters. It varies under different environment. 4 What to do when my cell phone can not search and find the headset? The cell phone will not find the headset if the headset and cell phone are not under the pairing mode.
12 Specifications Bluetooth specification Bluetooth profiles Operating distance Working time Standby time Charing input Charging time Dimensions Weight Bluetooth V2.1+EDR HSP, HFP, A2DP and AVRCP 10 meters, Class II Music: Up to 10 hours Talk: Up to 11 hours 200 hours DC 5A 130mA About 3 hours 158×156×55mm 103 g Notes: 1. This device complies with Part 15 of the FCC Rules.
13
