Owner's Manual

ManualsBrandsBDI ManualsFurnitureSequel 6052

These distinctive product conﬁgurations are protected by US and international patents, trade dress, and/or

Made in Taiwan. 05.19.2016 v2

T2 4mm Hex Wrench

C7 Wire Tray x 1

C4 Keypad x 1

C5 Power Cord x 1

C3 Control Module x 1

C8 Glass Panel x 1

A1 Main Panel x 1

C1 Leg x 2

C6 Cord Conduit x 1

C2 Foot x 2

bdiusa.com

customerservice@bdiusa.com

SEQUEL

6051/6052

LIFT DESK

H5 1/4-20 x 12mm Screw x 6

Tool Required:

Phillips Screwdriver

H2 #6 Wood Screw x 6

H3 M6 x 12mm Screw x 12

H8 Glass Bumper x 3

C9 Grommet Cover x 1

H9 Dual Lock Dot x 8

Product Registration

Registering your new BDI product allows us to send you important

product updates, service information and helpful hints related to your BDI

products. Register today, and you will be entered to win free a BINK table

from BDI: www.bdiusa.com/register

Placement and Maintenance

Sequel® Lift Desk is designed for indoor use on level floors. Clean glass

with glass cleaner, and steel parts and wood veneer with a moist cloth.

Your Sequel® Office furniture is engineered for easy assembly. Carefully

follow this procedure to prevent any damage. Do not use power tools

for assembly of this product.

Step 1

Unpack and identify the parts listed below. The assembly workspace

should be a non-marring surface such as carpet. For missing hardware

pieces, please contact BDI Customer Service at customerservice@bdiusa.

com. For all other concerns, please contact your BDI retailer.

H7 Leveler x 4

H6 Cord Clip x 6

H1 #10 Wood Screw x 4

T1 5mm Hex Wrench

H4 M6 x 16mm Screw x 8

OWNER’S MANUAL

Summary of content (15 pages)

PAGE 1
SEQUEL® 6051/6052 LIFT DESK bdiusa.com customerservice@bdiusa.com OWNER’S MANUAL T1 5mm Hex Wrench Product Registration Registering your new BDI product allows us to send you important product updates, service information and helpful hints related to your BDI products. Register today, and you will be entered to win free a BINK table from BDI: www.bdiusa.
PAGE 2
Step 2 - Install Control Module and Keypad Lay top panel upside down on a soft surface (like carpet). Attach Keypad C4 on the desired side (left or right) with 2 Wood Screws H1. Orient the Control Module C3 so that the Keypad port is facing the Keypad side and secure between the 2 steel rails with 2 Wood Screws H1 as shown. Route the Keypad cord into the groove in the panel and through the hole in the metal frame.
PAGE 3
Step 3 - Secure the keypad cord into the groove using 6 cord clips H6 and 6 wood screws H2. Connect keypad cord into the Control Module Port (labeled HS) and bundle the slack with the Hook & Loop Tie. Hook & Loop Tie H2 x 6 H6 x 6 Groove for Keypad Cord 3 SEQUEL 6051/52 LIFT DESK bdiusa.com customerservice@bdiusa.
PAGE 4
Step 4 - Attach 2 Legs C1 with 6 Screws H3 per Leg using Hex Wrench T1. Start all 6 screws before tightening them down. Tighten the 2 outside screws first, then tighten the other 4 screws. Step 5 - Connect the leg cords to the closest port of the control module and bundle up any slack using the hook & loop tie. T1 H3 x 12 1- Tighten the 2 outside screws first C1 x 2 2- Tighten the front/back screws next 4 SEQUEL 6051/52 LIFT DESK bdiusa.com customerservice@bdiusa.
PAGE 5
Step 6 - Attach each Foot C2 with 4 Screws H4 using Hex Wrench T2. The long end of the foot faces the front edge of the desk. Thread in Levelers H7 into the bottom front and back corners of each foot. H4 H4 x 4 H7 x 4 C2 x 2 5 SEQUEL 6051/52 LIFT DESK bdiusa.com customerservice@bdiusa.
PAGE 6
Optional Drawer Assembly for 6052 Attach the optional Drawer (for 6052) using 4 Screws H10 that came with your drawer as shown. H10 x 4 A2 6 SEQUEL 6051/52 LIFT DESK bdiusa.com customerservice@bdiusa.
PAGE 7
Step 7 - Plug the Power Cord C5 into the power port on the Control Module C3 (labeled AC). Step 8 - Turn the desk upright and plug it in to adjust the height With the help of another person, carefully flip the desk on to its feet. Plug the other end of the Power Cord into the nearest wall socket. Refer to the User Manual on Page 13 and follow the Reset Procedure. You may now adjust the height of your desk to make the remaining steps easier. 2 Person Task 7 SEQUEL 6051/52 LIFT DESK bdiusa.
PAGE 8
Step 9 -Install the glass bumpers. Install the 3 glass bumpers H8 as shown. H8 x 3 Step 10 - Install the glass panel. With the help of another person, carefully place the Glass Panel C8 on top of the desk top with the metal pucks facing down. The stem of the glass pucks should slip into 4 holes. Secure the glass panel in place from below using 4 Screws H5. Place Grommet Cover C9 into the grommet hole. 2 Person Task C9 C8 H5 x 4 8 SEQUEL 6051/52 LIFT DESK bdiusa.com customerservice@bdiusa.
PAGE 9
Attach dual lock fastener to the bottom of the surge protector (optional) Secure 4 pairs of Dual-Lock Dots H9 to the bottom corners of the surge protector. Surge Protector H9 Dual- Lock Peel and stick Attach Dual Lock together Attach the surge protector (optional) For easy installation, raise the height of the desk. Determine where you prefer the surge protector to be mounted. We suggest just behind the metal rails towards the leg closest to your wall outlet. Make sure the area is dust free.
PAGE 10
Attach the Cord Conduit (optional) Remove adhesive film and attach the Cord Conduit C6 to the back of the top section of the leg nearest the wall outlet. Insert power cord(s) into the Cord Conduit. C6 Remove excess lubricant from legs When new, the legs may have excess lubricant. Extend the legs to their highest position and wipe off excess lubricant with a clean, dry cloth or rag. 10 SEQUEL 6051/52 LIFT DESK bdiusa.com customerservice@bdiusa.
PAGE 11
Attach the wire tray (optional) Determine if you prefer the wire tray to be centered, shifted left or shifted right. If you plan to use a monitor arm, it might be better to shift the position of the Wire Tray to make the monitor arm attach more centrally. Attach the metal Wire Tray C7 to the back edge of the bottom of the desk with 2 Screws H5. Shifted Right Shifted Left C7 Wire Tray H5 x 2 11 SEQUEL 6051/52 LIFT DESK bdiusa.com customerservice@bdiusa.
PAGE 12
Attach a monitor arm (optional) The Sequel Lift Desk is compatible with most third party monitor arms. Attach your monitor arm on either side of the grommet hole along the back edge (see gray area below), staying at least 1" away from the grommet hole. Optional Monitor Arm (NOT INCLUDED) 12 SEQUEL 6051/52 LIFT DESK bdiusa.com customerservice@bdiusa.
PAGE 13
User Manual Caution! 4HRL Z\YL [OLYL HYL UV VIZ[HJSLZ \UKLY [OL WH[O VM [OL KLZR 4HRL Z\YL [OL KLZR [VW PZ UV[ [V\JOPUN HU` ^HSSZ 4HRL Z\YL HSS [OL JVYKZ HYL SVUN LUV\NO [V YLHJO SV^LZ[ HUK OPNOLZ[ KLZR WVZP[PVUZ ! ! Important: @V\ T\Z[ YLZL[ [OL KLZR WYPVY [V \ZL Reset Procedure: 1. 2. 3. 4. 5. 6. Press and hold the DOWN button on the keypad until the desk reaches its lowest height. Release the DOWN button. Press and hold the DOWN button again until the LED sidplay reads “RST”.
PAGE 14
Height Adjustment The desk base can be adjusted by pressing and holding either the UP or DOWN button until the desired height is reached. To program up to four presets, use the up/down buttons to find a desired height, then press “M” followed by a number 1-4. Caution: Once a preset button is pushed, the desk will move to the programmed height. To stop movement, press any button on the key pad.
PAGE 15
Technical Specifications Height Range 24.75”–49.75” (63–126 cm) Travel Speed 1.5" per second Weight Capacity 150 lbs (68 kg) Duty Cycle 10%, Max 2 minutes with 18 minutes off Memory 4 position presets Monitor Arm Compatible Yes Warranty 3-Year Limited Warranty Trouble Shooting If your desk is not functioning properly it may need to be reset. Follow the RESET procedure above. If your LED readout displays an error message Er1 confirm that all wired connections are secure.