Owner's Manual

ManualsBrandsBDI ManualsEntertainment FurnitureCorridor 8175

Product Registration

Registering your new BDI product allows us to send you important

product updates, service information and helpful hints related to your

BDI products. Register today, and you will be entered to win free a BINK

table from BDI: www.bdiusa.com/register

Placement and Maintenance

Corridor

Media furniture is designed for indoor use on level floors.

Clean glass with glass cleaner, and steel parts and wood veneer with a

moist cloth.

Your Corridor

Media furniture is engineered for easy assembly.

Carefully follow this procedure to prevent any damage.

Do not use power tools for assembly of this product.

Step 1

Unpack and identify the parts listed below. The assembly workspace

should be a non-marring surface such as carpet. For missing

hardware pieces, please contact BDI Customer Service at

customerservice@bdiusa.com. For all other concerns, please

contact your BDI retailer.

bdiusa.com

customerservice@bdiusa.com

CORRIDOR

8175

MEDIA CABINET

B1 Hex Wrench x 1

A Phillips Screwdriver x 1

D 1/4-20 x 10 mm

Machine Screw x 16

H M4 x 35 mm

Machine Screw x 4

I Door Pull x 2

B2 Hex Wrench x 1

G 1/420 x 60 mm

Machine Screw x 4

E Metal Leg x 2

F Metal Rail x 2

J Rubber Bumper x 7

These distinctive product conﬁgurations are protected by US and international patents, trade dress, and/or

Made in China. 06.28.2016 V3

C Cabinet x 1

K Glass Top x 1

L Adjustable Shelf x 2

M Back Panel x 1

Summary of content (5 pages)

PAGE 1
CORRIDOR® 8175 MEDIA CABINET bdiusa.com customerservice@bdiusa.com Product Registration Registering your new BDI product allows us to send you important product updates, service information and helpful hints related to your BDI products. Register today, and you will be entered to win free a BINK table from BDI: www.bdiusa.com/register Placement and Maintenance Corridor® Media furniture is designed for indoor use on level floors.
PAGE 2
Step 2 - Build Base Assembly Slide Metal Leg E into Metal Rail F and attach by using Hex Wrench B1 and Screw D. F E ¨ ¨ D D E F ¨ ¨ D D Dx8 Step 3 - Carefully lay Cabinet C on its back. Using Hex Wrench B1, attach the base assembly to the bottom of the Cabinet C with Screw D and Screw G. *Note: Each of the metal legs has levelers that can be adjusted using the Hex Wrench B2. C G D G D D G Gx4 Dx8 2 CORRIDOR 8175 MEDIA CABINET bdiusa.com customerservice@bdiusa.
PAGE 3
Step 4 - Install Door Pulls and Rubber Bumpers Position the cabinet upright and install Door Pulls I using Screw H and Screwdriver A. Adhere Rubber Bumper J at least one (1) inch from edges of the cabinet and one centered as shown below. J J J J J J J I H H Step 5 - Install Glass Place Glass Top K on top of Cabinet C . Position glass flush with cabinet front doors. K C 3 CORRIDOR 8175 MEDIA CABINET bdiusa.com customerservice@bdiusa.
PAGE 4
Step 6 -Install Back Panel Install Back Panel M to the backside of the cabinet by inserting top edge in upper channel then tipping bottom edge forward and into lower channel. NOTE: Velcro straps are included for your convenience to facilitate wire management. 1 M 2 Adjustable Shelves If desired, lift Adjustable Shelf L away, loosen & remove related Shelf Support Pins, reinstall the Shelf Support Pins at desired height, then reinstall Adjustable Shelf.. L L 4 CORRIDOR 8175 MEDIA CABINET bdiusa.
PAGE 5
Fine tuning your new BDI Corridor Home Theater Furniture These steps are to be followed after you have unpacked and completed the simple assembly instructions for your Corridor AV cabinet. Due to jostling in freight or perhaps an uneven floor, the doors on your Corridor cabinet may not appear to be in perfect alignment. Making a few minor adjustments can rectify this situation. Be aware that depending on your situation, patience and a bit of trial and error are required.