Owner's Manual

ManualsBrandsBDI ManualsEntertainment FurnitureAudio/video cabinet for TVs up to 85" (Charcoal Stained Ash)

B1 - Hex Wrench

x 1

B2 - Hex Wrench

x 1

CORRIDOR

8179

Corridor is engineered for easy assembly. Carefully follow this

procedure to prevent any damage.

Placement and Maintenance

Corridor is designed for indoor use on level floors. Clean wood

veneer with a moist cloth. Clean glass with glass cleaner.

Step 1

Unpack and Identify

Unpack and identify the components at left. Note that some

components are shipped inside the cabinet. The assembly

workspace should be a non-marring surface such as carpet. For

missing hardware pieces, please contact BDI Customer Service

at customerservice@bdiusa.com. For all other concerns, please

contact your BDI Retailer.

For your convenience, assembly with or without wheels.

Component List

;OLZLKPZ[PUJ[P]LWYVK\J[JVUÄN\YH[PVUZHYLWYV[LJ[LKI`<:HUK

international patents, trade dress, and/or copyright laws.

BDI are trademarks of Becker Designed, Inc.

Made in China. 8179REV1010312v1

ASSEMBLY INSTRUCTIONS

BDIUSA.COM CUSTOMERSERVICE@BDIUSA.COM

C - Cabinet

x 1

G - 1/4-20 x 37 mm

Machine Screw

x 6

H - M4 x 35 mm

Machine Screw

x 8

F - Metal Rail

x 2

E - Metal Leg

x 2

E1 - Wheel Assembly

x 4

E2 - Leveler

x 4

D - 1/4-20 x 10 mm

Machine Screw

x 16

I - Pull

x 4

A - Phillips Screwdriver

x 1

M - Back Panel

x 2

L - Adjustable Shelf

x 2

K - Glass Top

x 1

J - Rubber Bumper

x 6

Installations with wheels:

Attach Wheel Assembly

(E1) to Metal Leg (E) using

Leveler (E2) and Screw (D).

*Note: Orient Wheel

Assembly (E1) with larger

hole towards outside.

Installations without wheels:

Install Leveler (E2) to Metal

Leg (E).

Summary of content (5 pages)

PAGE 1
A S S E M B LY INSTRUCTIONS CORRIDOR 8179 Component List A - Phillips Screwdriver x1 B1 - Hex Wrench x1 B2 - Hex Wrench x1 C - Cabinet x1 D - 1/4-20 x 10 mm Machine Screw x 16 E - Metal Leg x2 E1 - Wheel Assembly x4 E2 - Leveler x4 F - Metal Rail x2 G - 1/4-20 x 37 mm Machine Screw x6 BDIUSA.COM CUSTOMERSERVICE@BDIUSA.COM Corridor is engineered for easy assembly. Carefully follow this procedure to prevent any damage. Placement and Maintenance Corridor is designed for indoor use on level floors.
PAGE 2
Step 2 Build Base Assembly Slide Metal Leg (E) into Metal Rail (F) and attach by using Hex Wrench (B) and Screw (D). E E ¨ F F ¨ D D ¨ ¨ D D Step 3 Carefully lay Cabinet (C) on its back. Using Hex Wrench (B), attach the base assembly to the bottom of the Cabinet (C) with Screw (D) and Screw (G). *Note: Each of the metal legs has levelers that can be adjusted from inside the cabinet using the Hex Drivers (B). Gx6 Dx8 CORRIDOR 8179 2 ASSEMBLY INSTRUCTIONS BDIUSA.COM CUSTOMERSERVICE@BDIUSA.
PAGE 3
Step 4 Install Pulls and Rubber Bumpers Position the cabinet upright and install door Pulls (I) using Screw (H) and Screwdriver (A). Install Rubber Bumper (J) at least an inch from edges of the cabinet. J J J J J H I H J Step 5 Install Glass Place Glass Top (K) on top of Cabinet (C). Flush glass with cabinet front doors. K CORRIDOR 8179 3 ASSEMBLY INSTRUCTIONS BDIUSA.COM CUSTOMERSERVICE@BDIUSA.
PAGE 4
Step 5 Install Back Panels Install both Back Panel (K) to the backside of the cabinet by inserting top edge in upper channel, then tipping bottom edge forward and into lower channel. NOTE: Velcro straps are included as wire management for your convenience. The shelf pins located inside the left and right cabinet space may be repositioned, allowing you to raise or lower each Adjustable Shelf (L) to the desired level. 2 1 CORRIDOR 8179 4 ASSEMBLY INSTRUCTIONS BDIUSA.COM CUSTOMERSERVICE@BDIUSA.
PAGE 5
Fine tuning your new BDI Corridor Home Theater Furniture These steps are to be followed after you have unpacked and completed the simple assembly instructions for your Corridor AV stand. Due to jostling in freight or perhaps an uneven floor, the doors on your Corridor stand may not appear to be in perfect alignment. Making a few minor adjustments can rectify this situation. Be aware that depending on your situation, patience and a bit of trial and error are required.