Assembly Instructions

ManualsBrandsBDI ManualsFurnitureCorridor TV Stand for TVs up to 88"

Product Registration

Registering your new BDI product allows us to send you important

product updates, service information and helpful hints related to your BDI

products. Register today, and you will be entered to win free a BINK table

from BDI: www.bdiusa.com/register

Placement and Maintenance

Your Corridor Console is designed for indoor use on level floors. Clean

wood veneer and steel parts with a moist cloth.

Corridor is engineered for easy assembly. Carefully follow this procedure

to prevent any damage. Do not use power tools for assembly of

this product.

Step 1 Unpack and identify the parts listed below. The assembly

workspace should be a non-marring surface such as carpet. For missing

hardware pieces, contact BDI Customer Service at:

customerservice@bdiusa.com.

For all other concerns, please contact your BDI retailer.

These distinctive product conﬁgurations are protected by US and international patents, trade dress, and/or

Made in China. 10.04.2017 V1

CORRIDOR SV

™

7129

4 BAY CONSOLE

A1 Cabinet x 1

C5 Glass Top x 1

C4 Side Shelf x 2

C3 Middle Shelf x 1

bdiusa.com

customerservice@bdiusa.com

T2 Hex Wrench x 1

H1 1/4-20 x 15 mm

Machine Screw x 8

H2 1/4-20 x 63 mm

Machine Screw x 8

T1 Phillips Screwdriver x 1

A2 Sub Frame x 2

A3 Leg Frame x 2

H3 M4 x 35 mm

Machine Screw x 8

H4 Rubber Bumper x 8

H5 Door Pull x 4

Summary of content (5 pages)

PAGE 1
CORRIDOR SV™ 7129 4 BAY CONSOLE Product Registration Registering your new BDI product allows us to send you important product updates, service information and helpful hints related to your BDI products. Register today, and you will be entered to win free a BINK table from BDI: www.bdiusa.com/register Placement and Maintenance Your Corridor Console is designed for indoor use on level floors. Clean wood veneer and steel parts with a moist cloth. Corridor is engineered for easy assembly.
PAGE 2
Step 2 - Attach the 2 Leg frames A3 to Sub-frame A2 with 8 Screws H1 using Hex wrench T2. Make sure the red arrow on the sub-frame faces the same direction as the direction of the leg frames. A3 Red arrow H1 Screw x 8 T2 H1 A2 A2 T2 Step 3 Quad - With help from another person, carefully position the cabinet A1 upside-down (as shown) or on its back. Caution-do not remove blocking above the shelves. Attach the base to the cabinet with 8 Screws H2 using Hex Wrench T2.
PAGE 3
Step 4 - With help from another person, carefully position the cabinet upright and install Door Pulls H5 using Screws H3 and Screwdriver T1. Adhere Rubber Bumpers H4 about 1 inch (25mm) from edges of the cabinet as shown below. 2 Person Task H4 H4 H4 H4 H4 H4 H4 H4 H3 H5 H3 H5 Step 5 - Place glass top C5 on top of the cabinet. Position glass flush with cabinet front doors. 2 Person Task 3 CORRIDOR 7129 CONSOLE bdiusa.com customerservice@bdiusa.
PAGE 4
Step 6 - The shelf pins located inside all three cabinet spaces may be repositioned using Screwdriver T1, allowing you to raise or lower Middle and Side Shelves C3 and C4 to the desired level. C3 C4 T1 4 CORRIDOR 7129 CONSOLE bdiusa.com customerservice@bdiusa.
PAGE 5
Fine tuning your new BDI Corridor Home Theater Furniture These steps are to be followed after you have unpacked and completed the simple assembly instructions for your Corridor AV cabinet. Due to jostling in freight or perhaps an uneven floor, the doors on your Corridor cabinet may not appear to be in perfect alignment. Making a few minor adjustments can rectify this situation. Be aware that depending on your situation, patience and a bit of trial and error are required.