Instruction Manual

ManualsBrandsBDI ManualsCabinets & ArmoiresBDI Cosmo 5720 Toasted Walnut Bar

Product Registration

Registering your new BDI product allows us to send you important

product updates, service information and helpful hints related to your

BDI products. Register today, and you will be entered to win free a

BINK table from BDI: www.bdiusa.com/register

Placement and Maintenance

Your Cosmo Bar is designed for indoor use on level floors.

Clean wood, metal, and porcelain surfaces with a damp cloth.

Cosmo is engineered for easy assembly. Carefully follow this procedure

to prevent any damage. Do not use power tools for assembly of this

product.

Step 1

Unpack and identify the parts listed below. The assembly workspace

should be a non-marring surface such as carpet. For missing hardware

pieces, contact BDI Customer Service at:

customerservice@bdiusa.com.

For all other concerns, please contact your BDI retailer.

bdiusa.com

customerservice@bdiusa.com

These distinctive product conﬁgurations are protected by US and international patents, trade dress, and/or

Made in China. 12.05.2019 V3

COSMO

™

5720

BAR

Tool Required:

Slotted Screwdriver

A1 Cabinet x 1

A2 Lower Shelf x 1

C6 Middle Drawer

Liner x 1

C7 Side Drawer

Liner x 2

C5 Anti-skid Pad x 2

T1 Hex Driver x 1

H1 M6 x 12mm Screw

x 26

C3 Bottom Connector

Tube x 2

H5 Micro HDMI/USB

charge cord x 1

C2 Top Connector Tube x 2

C1 Base Frame x 2

T2 Leveler Wrench x 1

H3 Wall Anchor

Strap x 2

H4 Rechargeable

Strip Light

Summary of content (10 pages)

PAGE 1
COSMO™ 5720 BAR Product Registration Registering your new BDI product allows us to send you important product updates, service information and helpful hints related to your BDI products. Register today, and you will be entered to win free a BINK table from BDI: www.bdiusa.com/register Placement and Maintenance Your Cosmo Bar is designed for indoor use on level floors. Clean wood, metal, and porcelain surfaces with a damp cloth. Cosmo is engineered for easy assembly.
PAGE 2
Step 2 - Base Assembly Position base frame C1 on the floor with tabs facing up. Slide both top connector tubes C2 onto the 2 large U shaped tabs of base frame C1 making sure the holes are facing inside. Slide both bottom connector tubes C2 onto the 2 small U shaped tabs of base frame with holes facing down. Attach connector tubes using 8 screws H1. Sleeve the other base frame C1 over the assembly as shown below and tighten all 16 screws H1 with hex wrench T1.
PAGE 3
Step 3 - Base Attachment With help from another person, carefully position the cabinet A1 onto at least two layers of packing material and orient on its back as shown. Note: the packing material creates finger space to lift the cabinet after attaching the base. Position the base as shown and attach with 4 screws H1 and tighten with hex wrench T1. 2 Person Task A1 Cabinet x 1 2 layers of honeycomb packing material H1 H1 H1 H1 T1 3 COSMO 5720 BAR H1 x 4 bdiusa.com customerservice@bdiusa.
PAGE 4
Step 4 - Standing the Unit Position the anti-skid pads C5 under the back legs as indicated with arrow #1 making sure that the pads are centered on the end of the legs. With 2 people (1 person on each side) carefully and slowly lift the cabinet with hands placed along the edges of the cabinet indicated with arrow #2. 2 Person Task Leg centered on Anti-skid pad C5 Lift 1 1 C5 Anti-skid pad x 2 4 COSMO 5720 BAR 2 Recommended hand positions (both sides) 2 bdiusa.com customerservice@bdiusa.
PAGE 5
Step 5 - Wall Preparation CAUTION! DO NOT allow children to swing on the open doors. It is strongly recommended that you anchor your Cosmo Bar cabinet to the wall using two anchor straps H3 included. Determine the desired location of your Cosmo Bar and then position the bar 24" in front of the wall. Mark the wall and insert 2 wall inserts (not included) in the position indicated below. H3 Anchor Strap x 2 wall anchors (not included) 71cm 28" 175cm 69" 61cm 24" 5 COSMO 5720 BAR bdiusa.
PAGE 6
Step 6 - Wall Attachment Attach 1 end of the anchor straps to the wall. Carefully move your Cosmo bar close to the wall and attach the loose end of the anchor straps to the top of the cabinet using screws H1 going into the threaded inserts as shown. Tighten with hex wrench T1. H1 H3 Anchor Strap T1 H1 x 2 Step 7 - Lower Shelf Installation Tilt the lower shelf as shown, insert the shelf into the front opening of the base and rotate carefully down onto the lower cross bars of the frame.
PAGE 7
Step 8 - Light Installation Find the rechargeable strip light H4. Using the Micro HDMI/USB charge cord H5, charge the light for 6 hours. Once charged, install it onto the metal strip (it is held with magnets) located in the angled recess towards the top front of the cabinet. Make sure the proximity sensors are facing forward and the light switch is turned on. The light is designed to turn off automatically when the cabinet doors are closed.
PAGE 8
Step 10 - Shelf Adjustment Adjust the height of the adjustable shelf if needed by moving the positions of the shelf pins. Adjustable Shelf Mirror Bottles and cans Porcelain Surface Wine Bottle Storage 8 COSMO 5720 BAR Wine Glass Storage Reposition Shelf Pins (if needed) bdiusa.com customerservice@bdiusa.
PAGE 9
Step 11 - Leveling and Adjusting the Door Gaps With both doors closed, check to see if the top corners of the doors align. If not, dial out the corresponding front leveler under the door that is sagging. Example: If the door on the right is low, dial out the right front leveler to raise the door back into alignment with the left door. To move the right door up, dial the front, right leveler out. To move the left door up, dial the left, front leveler out.
PAGE 10
Cleaning If a spill occurs, the porcelain surface on your Cosmo Bar may be removed for cleaning. To remove, open the drawer about 8", reach inside and find the 60mm disc just under the front center edge of the porcelain. Rotate the disc 180 degrees. Lift the porcelain out by pushing up from below. Rotate Disc to Unlock Porcelain surface 10 COSMO 5720 BAR Unlocked Position Disc bdiusa.com customerservice@bdiusa.