Instruction Manual

ManualsBrandsBDI ManualsBuffets & SideboardsBDI Cosmo 5729 Toasted Walnut Credenza

Product Registration

Registering your new BDI product allows us to send you important

product updates, service information and helpful hints related to your

BDI products. Register today, and you will be entered to win free a

BINK table from BDI: www.bdiusa.com/register

Placement and Maintenance

Your Cosmo Console is designed for indoor use on level floors.

Clean wood, metal, and porcelain surfaces with a damp cloth.

Cosmo is engineered for easy assembly. Carefully follow this

procedure to prevent any damage. Do not use power tools for

assembly of this product.

Step 1

Unpack and identify the parts listed below. The assembly workspace

should be a non-marring surface such as carpet. For missing

hardware pieces, contact BDI Customer Service at:

customerservice@bdiusa.com.

For all other concerns, please contact your BDI retailer.

bdiusa.com

customerservice@bdiusa.com

These distinctive product conﬁgurations are protected by US and international patents, trade dress,

COSMO

™

5729

CONSOLE

Tool Required:

Phillips Driver x 1

Tool Provided:

T1 Hex Driver x 1

A1 Cabinet x 1

C5 Drawer liner x 2

C2 Front Base Frame x 1

C3 Connector Tube x 3

C1 Back Base Frame x 1

H1 M6 x 12mm

Screw x 10

H2 M6 x 35mm

Screw x 2

Summary of content (7 pages)

PAGE 1
COSMO™ 5729 CONSOLE Product Registration Registering your new BDI product allows us to send you important product updates, service information and helpful hints related to your BDI products. Register today, and you will be entered to win free a BINK table from BDI: www.bdiusa.com/register Placement and Maintenance Your Cosmo Console is designed for indoor use on level floors. Clean wood, metal, and porcelain surfaces with a damp cloth. Cosmo is engineered for easy assembly.
PAGE 2
Step 2 - Base Assembly Position the front and back base frames C1 and C2 as shown. Position the connector tubes C3 as shown (no holes should be visible on the outside ends). Slide the metal tabs into the ends of the connector tubes. Attach base frames to connector tubes using 6 screws H1. Tighten with hex driver T1. C3 C1 H1 C3 C2 Metal tabs C3 No holes here T1 H1 x 6 Step 3 - Base Attachment Make sure the packing material bracing the 2 inner shelves is still in place before rotating the cabinet.
PAGE 3
Step 4 Drawer liner Installation Place one drawer liner C5 into each drawer. Step 5 Cabinet Leveling Check to make sure your Cosmo Console is level. Levelers are located underneath each leg and can be dialed up or down to level the unit if necessary (see below). Step 6 Shelf Positioning The shelves may be positioned at any of the available locations corresponding with threaded inserts inside the cabinet by moving the shelf pins. Use a Phillips driver to loosen, reposition, and re-tighten the shelf pins.
PAGE 4
Fine tuning your new BDI Cosmo Console These steps are to be followed after you have unpacked and completed the simple assembly instructions for your Cosmo Console. Due to jostling in freight or perhaps an uneven floor, the doors on your Cosmo console may not appear to be in perfect alignment. Making a few minor adjustments can rectify this situation. Be aware that depending on your situation, patience and a bit of trial and error are required.
PAGE 5
Porcelain Top Removal Your Cosmo Console features a durable, heat resistant porcelain top. The top may be cleaned with mild soapy water on a damp cloth. If liquid spills into the seam, the porcelain top may be removed for cleaning purposes, or may be replaced in case of damage. To remove the porcelain: 1) open all 4 doors, partially open the upper left drawer. 2) Using a Phillips screwdriver, remove the screw (indicated below) from each front corner of the drawer.
PAGE 6
Porcelain Top Removal (cont.) 4) locate the 4 metal plates that connect the porcelain to the cabinet. 5) Use Hex driver T1 to remove all screws holding the metal plates. 6) Once all four metal plates are removed, the porcelain top may be lifted out by pushing up from below as shown (arrow #2). After cleaning, re-insert the porcelain top and re-attach the 4 metal plates.
PAGE 7
Drawer Adjustment (if needed) The 2 drawers on your Cosmo Console are adjustable as much as 2mm up, down, left, right, back or forward. If the drawers are out of alignment, follow the steps below: Forward Removing this screw allows the drawer to be adjusted (or removed) Backward 1) Rotating the black wheel towards the inside of the drawer moves the drawer backward, deeper into the cabinet. Left Right 2) Rotating the white wheel towards you moves the drawer to the left. Rotating away moves it right.