SEQUEL® 20 6101/6103 DESK/COMPACT DESK INSTRUCTION MANUAL LET’S GET STARTED.
Congratulations on the purchase of your Sequel 20 Desk 6101 / Compact Desk 6103 from BDI. Your desk has been designed to provide a lifetime of enjoyment. This manual will provide you with assembly instructions and other helpful information that will ensure that you get the most out of your desk. Please save it for future reference. Your Sequel 20 Desk has been engineered for simple assembly. Please follow these directions carefully to prevent any damage.
HARDWARE AND COMPONENTS Unpack and identify the parts listed below. The assembly workspace should be a non-marring surface such as carpet. For missing hardware pieces, please contact BDI Customer Service at customerservice@bdiusa.com. Do not use power tools for assembly of this product. For all other concerns, please contact your BDI retailer.
HARDWARE AND COMPONENTS PART # DESCRIPTION C5 Upper Horizontal Frame PART # DESCRIPTION C6 Wire Tray QUANTITY 1 QUANTITY 1 PART # C7 PART # C8 DESCRIPTION 6108 Back Panel* see Note in Step 9 DESCRIPTION QUANTITY 1 QUANTITY PART # C9 PART # DESCRIPTION QUANTITY Front Panel 1 NEED ASSISTANCE? customerservice@bdiusa.com DESCRIPTION QUANTITY Top Panel 1 C10 Drawer Liner 1 BDIUSA.
ASSEMBLY STEP 1. INSTALL LEVELERS Install (H2) Levelers into the bottom of (C1) Left and (C2) Right Leg Frames. H2 H2 H2 PART/DESCRIPTION QTY H2 H2-LEVELER 4 C2 C1 ASSEMBLY STEP 2. INSTALL SCREWS (PARTIALLY) With levelers down, partially install (H1) Screws into the upper holes of the paired inserts on the inside edges of (C1) Left and (C2) Right Leg Frames. (H1) Screw heads should be 1/4" (6mm) away from frame. H1 QTY H1-SCREW 8 H1 H1 H1 H1 H1 C1 C2 H1 6 | BDIUSA.
STEP 3. INSTALL DRAWER ASSEMBLY FRAME ASSEMBLY On a soft surface such as a carpet, position (C2) Right Leg Frame as shown and hook (C3) Drawer Assembly Frame onto the partially threaded screws on the top of (C2) Right Leg Frame. Slide the frame down so that the screws go into the keyhole slot. Wood facia facing thinner section of front leg C3 C2 C2 C3 Hook onto partially threaded screw head Insert (H1) Screws into the lower holes and partially tighten with (T1) Hex Wrench.
ASSEMBLY STEP 4. INSTALL DRAWER ASSEMBLY FRAME Lift and hook the (C3) Drawer Assembly Frame onto the 2 partially threaded screws at the top of (C1) Left Leg Frame. Insert (H1) Screws into the lower holes and partially tighten with (T1) Hex Wrench. PART/DESCRIPTION QTY T1-HEX WRENCH 1 H1-SCREW 2 Wood facia facing thinner section of front leg C3 C1 C3 C1 H1 8 | BDIUSA.
STEP 5. INSTALL LOWER HORIZONTAL FRAME ASSEMBLY Lift and hook the (C4) Lower Horizontal Frame onto the partially threaded screws as shown. Insert (H1) Screws into the lower holes and partially tighten with (T1) Hex Wrench. PART/DESCRIPTION QTY T1-HEX WRENCH 1 H1-SCREW 2 C2 C1 C1/C2 C4 C4 C1/C2 C4 H1 NEED ASSISTANCE? customerservice@bdiusa.com BDIUSA.
ASSEMBLY STEP 6. INSTALL UPPER HORIZONTAL FRAME Lift and hook the (C5) Upper Horizontal Frame onto the partially threaded screws as shown. Insert (H1) Screws into the lower holes and partially tighten with (T1) Hex Wrench. PART/DESCRIPTION QTY T1-HEX WRENCH 1 H1-SCREW 2 Including previous steps, fully tighten all screws! C5 C5 C2 C1/C2 C1/C2 C5 H1 C1 ASSEMBLY STEP 7.
STEP 8. ROTATE WIRE TRAY ASSEMBLY Rotate the (C6) Wire Tray down as shown. Position the desk. The wire tray may be used to hold power strips, surge protectors, and power bricks (not provided). Note: If positioning your desk in the middle of a room, power cords may be routed through the holes on the (C4) Lower Horizontal Frame. C6 C4 C6 STEP 9. INSTALL BACK PANEL—OPTIONAL ASSEMBLY If positioning your desk away from a wall, the (C7) Back Panel may be installed.
ASSEMBLY STEP 10. INSTALL TOP PANEL Install the (C8) Top Panel as shown and secure with (H1) Screws going though the metal tabs on the frame and into the inserts in the corners of the guide blocks under the (C8) Top Panel. Tighten using the (T1) Hex Wrench. PART/DESCRIPTION QTY T1-HEX WRENCH 1 H1-SCREW 6 C8 C8 H1 H1 H1 H1 H1 H1 ASSEMBLY STEP 11. INSTALL FRONT PANEL Install the (C9) Front Panel by placing the bottom edge into the channel on the front of the (C4) Lower Horizontal Frame.
STEP 12. INSTALL DRAWER LINER ASSEMBLY Open drawer and install (C10) Drawer Liner. C10 LEVEL DESK FINE TUNING If needed, dial out 1 or more of the levelers using (T2) Leveler Wrench. T2 NEED ASSISTANCE? customerservice@bdiusa.com BDIUSA.
CARE & MAINTENANCE GLASS Glass surface is maintained using household glass cleaner and a paper towel or cloth. SATIN-ETCHED GLASS This uniquely smooth-to-the-touch glass surface can be regularly maintained using household glass cleaner and a paper towel or cloth. Minor scratches or scuffs not eliminated using paper towel or cloth can usually be removed by using a ‘Magic Eraser’. Magic Eraser is a melamine foam product available at any grocery store or home improvement center.
WARRANTY BDI warrants to the original purchaser that for the below stated warranty term, BDI will repair or replace any product, part, or component covered by this warranty which fails under normal use as a result of a defect in material or workmanship. BDI will repair or replace the aforementioned product, part or component with a comparable product, part or component. The decision to repair or replace will be at BDI’s sole discretion.
These distinctive product configurations are protected by US and international patents, trade dress, and/or copyright laws. Sequel & BDI are trademarks of Becker Designed, Inc. All rights reserved. ©2020, BDI | V.03.26.2020 Made in Vietnam.