Inc. Motion Sensor User Guide

ManualsBrandsBEA ManualsHome Safety ProductEagle 10

75.5185.04 20070727 Page 1 of 8

EAGLE

USER GUIDE

NOTE: For mounting heights between 10’ and 16’, use BEA model 10EAGLEHM (high mount).

DESCRIPTION SPECIFICATION

Frequency: 24.125 GHz

Supply voltage:

12 to 24 V AC: ± 10%:

12 to 24 V DC: -10% / +30%:

Mounting height: Normal: 7’; Maximum: 10’-0”

Tilt angle:

0° to 90° vertical

-15° to +15° lateral

Detection area:

Wide

Narrow

13ft (W) x 6.5ft (D)

6.5ft (W) x 8.2ft (D) (supplied as optional)

Minimum detection speed: 2 in/sec. (measured in axis)

Power consumption: < 2 W

Standard output relay:

Max contact voltage

Max contact current

Max switching power

60 VDC / 125 VAC

1 A (resistive)

30W (DC) / 60VA (AC)

Hold time: 0.5 sec. to 9 sec. (adjustable)

Temperature range: -4°F to 131°F

Dimensions: 4.75in (W) x 3.15in (H) x 2.0in (D)

Weight: 0.5lbs

Material: ABS

Housing color: Black. Can be painted with non-metallic paint

Cable length: 6ft

1 Description

2 Technical Specifications

Terminal

Block

Narrow Antenna Storage Manual Set-Up Buttons

Wire Passage Hole Planar Antenna

Lateral and Angle

Adj. For Antenna

Opening Tab

Wire Opening Knockout

(inside the cover)

Front Cover

LED

Summary of content (8 pages)

PAGE 1
EAGLE USER GUIDE 1 Description Terminal Block Narrow Antenna Storage Wire Passage Hole Planar Antenna Manual Set-Up Buttons Lateral and Angle Adj. For Antenna Wire Opening Knockout (inside the cover) Front Cover Opening Tab LED NOTE: For mounting heights between 10’ and 16’, use BEA model 10EAGLEHM (high mount). 2 Technical Specifications DESCRIPTION SPECIFICATION Frequency: Supply voltage: 24.
PAGE 2
3 Installation 1 Tips The sensor must be firmly fastened to prevent vibration. 2 The sensor must not be placed directly behind a panel or any kind of material. The sensor must not have any object likely to move or vibrate in its sensing field. The sensor must not have any fluorescent lighting in its sensing field. Safety Precautions • • • • • • Shut off all power going to the header before attempting any wiring procedures. Maintain a clean & safe environment when working in public areas.
PAGE 3
Mechanical Installation Opening the sensor From behind, before installation From the front, after installation Mounting the sensor or 4 Paste the template at desired location. Insert screws but do not screw them fully in. Drill as instructed. Pass the cable where indicated. Optional cable routing: Notch the cover as shown in the picture.
PAGE 4
5 Mechanical Adjustments A. THE WIDTH OF THE SENSING FIELD IS DETERMINED BY THE CHOICE OF THE PLANAR ANTENNA (OPTION) 6.4’ 3.2’ 0 3.2’ 6.4’ 0 3.2’ Wide sensing field: 6.4’ Narrow sensing field: 3-element antenna 6-element antenna 9.
PAGE 5
6.4’ 3.2’ 3.2’ 6.4’ 0 3-Element Antenna 70º 6-Element Antenna For ceiling mounting, the vertical tilt angle of the antenna must be set at the maximum position of 70-75° and the spherical part of the sensor must be oriented in the opposite direction to the door. C.
PAGE 6
Programming Guide The Eagle is equipped with a Motion Tracking Feature (MTF). The MTF is available when the Eagle is used in the unidirectional mode. The Eagle is factory preset with the MTF ON. MTF is recommended for use in short vestibule areas to help reduce unwanted door hold-open time. Refer to the Programming Guide to alter this setting. BEA recommends keeping the MTF enabled for all applications.
PAGE 7
Sensitivity 0 = Minimum Sensitivity 9 = Maximum Sensitivity Default: 8 Detection Mode Detection mode offers 3 different levels of detection: Relay Hold Time Relay hold time refers to the hold time on the output relay of the Eagle. Values range from 0 to 9. 0 = .5 sec.
PAGE 8
4 Troubleshooting SYMPTOMS PROBABLE CAUSE CORRECTIVE ACTION The door will not open and no red LED lights up. The sensor power is off. Check the wiring and power supply. The door opens and closes constantly. The door control is set to level 3. Set door control to automatic mode (level 1). The sensor “sees” the door moving Increase the tilt angle and/or reduce the sensitivity and/or increase the immunity. Ensure the sensor is correctly fixed. Switch to unidirectional mode. Increase the immunity.