Install Instructions

ManualsBrandsBeacon Morris ManualsHeating SuppliesLouvered Front Panel for W42

Beacon/Morris

INSTALLATION INSTRUCTIONS • TYPES W & F

BWFII-4

Beacon/Morris

TWIN-FLOIII

260 NORTH ELM STREET, WESTFIELD, MASSACHUSETTS 01085

7555 TRANMERE DRIVE, MISSISSAUGA, ONTARIO L5S 1L4 CANADA

www.beacon-morris.com

GENERAL DESCRIPTION

The Twin-Flo III wall kits have been designed to accommodate a Beacon-Morris Twin-Flo III Model K42, K84, or K120

kickspace heater to deliver a comfortable stream of warmed air through the wall by a unit mounted in the wall, or on the

surface of the wall. Kits consist of front grille panels, back panel, and necessary mounting hardware. The kickspace

heater is sold separately.

The recessed (W kits) cabinet for the W42 will ﬁ t between 16" center studs. The W84/W120 will require a small amount of

framing to suit the mounting.

Installation instructions should be read thoroughly IN CONJUNCTION WITH INSTALLATION INSTRUCTIONS AND

WIRING DIAGRAM SUPPLIED WITH TWIN-FLO III HEATER UNITS, prior to starting installation.

WARNING: DISCONNECT POWER BEFORE SERVICING UNIT,

POTENTIAL ELECTRICAL SHOCK HAZARD!

ATTENTION: READ THESE INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO INSTALL, OPERATE, OR SER-

VICE THE BEACON-MORRIS TWIN-FLO III HEATERS! RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.

INSPECT THE SHIPMENT IMMEDIATELY WHEN RECEIVED TO DETERMINE IF ANY DAMAGE HAS OCCURRED

DURING SHIPMENT.

PRIOR TO INSTALL, CHECK FOR ANY VISIBLE DAMAGE.

2/12

RECESSED AND SURFACE MOUNT WALL KITS

RECESSED "W" / SURFACE MOUNT "F" WALL KIT

To be used in conjunction with Twin-FloIII • Type K

Kickspace Heater Installation Instructions

For use with K42/K84/K120 Kickspace Heaters

Summary of content (4 pages)

PAGE 1
BWFII-4 TWIN-FLOIII ® Beacon/Morris INSTALLATION INSTRUCTIONS • TYPES W & F RECESSED AND SURFACE MOUNT WALL KITS RECESSED "W" / SURFACE MOUNT "F" WALL KIT To be used in conjunction with Twin-FloIII • Type K Kickspace Heater Installation Instructions For use with K42/K84/K120 Kickspace Heaters ATTENTION: READ THESE INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO INSTALL, OPERATE, OR SERVICE THE BEACON-MORRIS TWIN-FLO III HEATERS! RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
PAGE 2
INSTALLATION OF TWIN-FLO III WALL MODELS - TYPE "W" AND TYPE "F" Figures D and F show exploded views of the wall models "W" & "F" Twin-Flo III's. Figure E shows the "W" type mounted in a wall with an air outlet at the top of the unit. Figure G shows the "F" type mounted. The louvers of the front panel will direct the air flow as shown. Use the following procedures for installation.
PAGE 3
Type "F" Installation 17 27/32 (453) F42 21 27/32 (555) F84 21 27/32 (555) F120 3 6 5 1F 23 29/32 (607) 24" (610) 7 18" (460) F42 22" (561) F84 22" (561) F120 4F 8 2F 9 CAT-55525A 4 3/8 (111) FIGURE F FIGURE G (Model 42 Shown) Description Figure F Parts List 1F 2F Front Panel Assembly Back Panel Assembly Part No.
PAGE 4
LIMITED WARRANTY Twin–Flo III Heaters The "Manufacturer" warrants to the original owner at the original installation site that the Twin–Flo Kickspace Heaters (the “Product”) will be free from defects in material or workmanship for five (5) years from the date of shipment from the factory.