User manual
IsatDock PRO - Installation & User Manual
2524
Operation of the IsatPhone Pro
Prepare the Inmarsat IsatPhone Pro
Ensure that the IsatPhone Pro Handset has the
latest compatible rmware installed. For more
information visit:
http://www.beamcommunications.com/
support/pro
Starting Up
1. Retract the antenna on the IsatPhone
Pro handset.
2. Place the IsatPhone Pro as per instructions
“Docking & Undocking” on page 23.
3. Turn vehicle ignition on. The IsatPhone
Pro will automatically power and the
handset will then start to initialise followed
by a 3 tone rising beep when a successful
connection has been made between the
docking station and the IsatPhone Pro.
4. Wait for the IsatPhone Pro handset to
register on the Inmarsat network. The
STATUS LED on the docking station will
turn green when a successful registration
has taken place.
5. You are now ready to make and receive calls.
45
o
C upper limit for the handset to charge the
battery whilst docked. If the battery temperature
exceeds this limit, then the IsatPhone Pro may
cease charging until the temperature is reduced.
Placing Voice Calls
Bluetooth® calls via IsatPhone Pro
The IsatDock PRO allows for Bluetooth audio
calls to be placed via the IsatPhone Pro handset
while docked. Consult the IsatPhone Pro manual
for further information on pairing and Bluetooth
discovery setup.
Speakerphone Phone Call Use
Mobile Originating
1. By default the IsatDock PRO will start all
calls in speakerphone mode when dialing
on the keypad without RJ11 or privacy
handset o hook.
2. Dial using the full Inmarsat dialing
sequence eg. 00 country code and
telephone number on the IsatPhone Pro
keypad whilst docked. Press the GREEN
button to start the connection.
3. A message will display on the IsatPhone Pro
handset to indicate the call is progressing.
4. Once the call is connected, the STATUS LED
will ash to indicate a call is in progress.
NOTE:
1. If the IsatPhone Pro is removed from the dock
during a call, the call will drop out during this
transition
2. One common cause for connection failure is
a at IsatPhone Pro battery which prevents
the IsatPhone Pro from turning ON. In these
instances the docking station will attempt to
charge the IsatPhone Pro handset while it is
switched OFF, until enough charge is present
for the IsatPhone Pro to turn ON. This
charging period can take up to 20 minutes
depending on how at the battery.
Pro handset
The IsatDock PRO provides charging power to
the IsatPhone Pro handset via its USB connector.
The IsatPhone Pro battery is a lithium-ion cell
which has a safety temperature range whilst
charging. This range is from 0 to 45 degrees
Celsius (32 to 113 degrees Fahrenheit).
Due to the increased heating eects on the
IsatPhone Pro handset whilst it is docked
and being charged, it is ideal for the ambient
temperature to be at least 18 degrees below the
5. Press the RED key on the IsatPhone Pro
handset or press the speakerphone button
to terminate the call.
Options:
A. During a call, you may use the optional
privacy handset by taking the privacy
handset out of its cup. This automatically
directs the call audio to the privacy handset.
B. To return the call back to “speakerphone”
mode, press the speakerphone button and
return the privacy handset to its cup.
Mobile Terminating
1. Answer the incoming call by pressing the
Speakerphone button or the GREEN key
on the IsatPhone Pro handset.
2. Once the call is in progress, the same options
are available as described in “Speakerphone
Phone Call – Mobile Originating”
3. Press the RED key on the IsatPhone Pro
handset or press the speakerphone button
to terminate the call.
Privacy Handset Use
Mobile Originating
1. Remove the privacy handset from its cup
2. Dial the phone number (using the full
country code) on the IsatPhone Pro
keypad whilst docked. Press the GREEN
button to start the connection.
3. A message is displayed on the IsatPhone
Pro to indicate a call is in progress.
4. Once the call is connected, the STATUS LED
will ash to indicate a call is in progress.
5. Press the RED key on the IsatPhone Pro
handset or return the privacy handset to
its cup to terminate the call.
Options:
A. During a call, you may switch to
“speakerphone” mode by pressing the
speakerphone button on the IsatDock.
Return the privacy handset to its cup.
B. To return the call back to the privacy handset,
remove the privacy handset from its cup.
Mobile Terminating
1. Answer the incoming call by un-cupping
the privacy handset from its cup.
2. Press the RED key on the IsatPhone Pro
handset or return the privacy handset to
its cup to terminate the call.
RJ11 POTS Phone Use
Mobile Originating
1. Lift the RJ11/POTS phone handset
“OFFHOOK” and listen for the dial tone.
The mute LED will ash yellow to indicate
the RJ11/POTS is in use.
2. Dial (using the full country codes) on the
RJ11 telephone keypad.
3. A message will display on the IsatPhone Pro
handset to indicate the call is progressing.
4. Once the call is connected, the STATUS LED
will ash to indicate a call is in progress.
5. Place the RJ11/POTS phone handset “ON
HOOK” to terminate the call.
Mobile Terminating
1. The RJ11/POTS phone will sound its ringer.
2. Lift the RJ11/POTS phone handset
“OFFHOOK” to answer the call.