User manual

ManualsBrandsBeam ManualsRadioRST825 SatRADIO

Handset Mode Transferred to Radio Mode

It is possible to make a call on the Intelligent Satellite handset and then place the handset back into the cradle to

connect the call through to the Radio network, in order to this you must activate the autodial switch by placing it in the

on position and then returning to the on position.

Using a Radio Handset DTMF Model

Using a DTMF compatible Two-way Radio it is possible to make or receive a call over the satellite network on the Radio device.

To make a call from a Radio handset a PIN is required. This is configurable to protect against unauthorized calling.

Making a call

1. Ensure that the Autodial switch on the main terminal is turned OFF as it is not possible to override autodial status.

2. Ensure the radio handset is on the same frequency as the main unit

3. Ensure the Satellite & Radio units are both powered ON (default PIN is 9876)

4. Whilst pressing the transmit button of the radio enter the PIN to access the system.

A. If PIN accepted a couple of acceptance pips are issued to indicate it is now ok to dial the phone number.

B. If the PIN number fails the handheld user receives a rising crescendo tone.

C.The access (after the PIN has been entered) times out after approx 10 secs, after which the PIN will need to be to be

re-entered.

D. In the event you have trouble entering the correct PIN wait 20 secs between attempts to allow the reset the unit.

E. Remember that it is not possible to transmit DTMF tones whilst another party is transmitting on another radio in

the group.

5. Once the acceptance pips are heard depress the transmit button and enter the full number you wish to call, and then

release the button.

A. Usually the transmit button of the radio needs to be pressed the entire time the number is being entered In order to

transmit the tones to the base unit.

B. If the dialed number seems to be a valid format acceptance pips will be transmitted to the handheld from the

satellite base.

C. If the number is invalid then a FAIL tone is sent; a long, low, beep.

6. Progress calling tones will be heard whilst the call connects, if the number was incorrect or the satellite network is not

available a busy tone will be heard through the radio network.

7. Hanging up the call: If the call was manually dialed or was incoming, it can be hung-up by the handheld user by simply

pressing the transmit button of the radio followed with a DTMF- 0. ( zero ).

System Power up

After installation has been completed, the RST825 system is now ready to be switched on. To turn on the system:

1. Switch on the Radio Component by simply selecting the ON position

2. Switch on the Satellite Component by simply selecting the ON position

3. Ensure that the Autodial switch is off, this will avoid making unnecessary calls when the unit is first powered on

4. Wait for the system to initialise and the DPL Satellite Handset to show registered status. This will typically take 40 to 60

seconds.

5. Once the Signal LED is solid green or orange, a call can be made attempted.

Operating the Two-Way Radio

The RST825 is installed with a Two-way radio interface that will be to the specification when the terminal was purchased. The

Radio component needs to be tuned to your desired channels to ensure that it can communicate with other radios within your

user group. Tone or CTSS squelching schemes can be programmed on the SatRADIO terminal.

To ensure optimum performance check the following

1. Ensure the Radio component is switched on and there is power to the Radio control handset

2. Ensure that the other Radios you want to interface with this unit are on the same frequency as the RST825 main terminal.

3. Test that from the Radio Control handset you can talk to the other radios on the same frequency / Channel. If not ensure

that the correct Channel has been selected and any required CTSS or tone squelch has been set up correctly.

4.There is a speaker control button on the RST825 that allows you to monitor the audio on the Radio. Simply press to switch

on/off

5.If you do not believe that you have communications between your Radio's consult your radio provider to ensure the unit has

been programmed to your required channel set up.

Operating the Satellite Module

The RST825 is installed with an Beam SatRADIO interface. The Satellite module provides the air interface to allow

two-way radio systems to interface to either another Beam SatRADIO terminal or any terrestrial phone service

anywhere on earth. There are three key ways to use the Satellite component of the RST825:

1. Handset Mode

This mode enables you to simply make a satellite telephone call using the Iridium handset of the terminal. Simply take the

handset off the cradle and make a satellite call as though you were using a typical cellular telephone.

Radio Handset DTMF Model

Using a DTMF compatible Two-way Radio it is possible to make or receive a call over the satellite network from the Radio

device. To make a call from a Radio handset a PIN is required. This is configurable, and to protect against unauthorized calling.

2. Autodial Mode

This mode enables the RST825 to continuously keep connected into a preset destination. This is ideal for emergency or

disaster recovery situations when the terminal may be being used as a primary communication tool or a replacement for a

Radio link that is down.

3. Satellite Handset Mode make a satellite telephone call using the Intelligent handset of the terminal, similar to using a

typical cellular telephone.

1. Remove the handset from the cradle by pushing the handset up

2. Enter the phone number you wish to call.

A. Consult your Satellite SIM provider for standard dialing instructions as this may vary depending on the type of

satellite SIM used

3. Once the number has been entered press the OK button to commence calling. To end call simply press C

To adjust the volume in call simply press the arrow up/down on handset

Connecting the Antenna Cable

Plug the antenna cable into the TNC antenna jack located on the front right side of the RST825 case.

Ensure that the specified cable being used does not exceed the Iridium maximum-loss rating of 3dB to

ensure maximum performance of the terminal. Refer to your Service Provider for full details or to purchase

and approved cable if using a cable other than the magnetic mount antenna included.

Connecting the Power Cable (if required)

Make sure the AC power switch supplying the RST825 is OFF. Plug in power cable into the 2-pin power socket

located on front left side of RST825 case. Only use plug pack provided.

Connecting to the Data Port (if required)

Connect a PC/Laptop to the Data port to make dial-up modem calls. The Iridium data speed is 2400bps, and can

be as high as 10kbytes if using Direct Internet compression. A data call cannot be made at the same time as a

voice call.

Connecting to the Config Port (if required)

Connect a PC/Laptop to the Log port to use the Beam Management System. The Config Port should only be used

for configuration and control of the terminal equipment.

Using your BEAM RST825 SatRADIO

Two-way

Antenna

Connector

Config Port

Data Port

Iridium

Antenna

Connector

Power

input

SIM

Socket

If any problems, try the following:

1. Repeat these instructions to ensure

everything has been completed.

2. Is there power to the unit?

> Check all connections and fuses.

3. Is the SIM card active?

> If not, refer to your Service Provider

4. If the antenna signal is not strong you

will need to move location to access

better coverage and re-test.

For additional troubleshooting refer to

your manual or visit us: